Zanussi ZBG 861 manual Installation Solid Pipe Installation

Page 41

INSTALLATION Solid Pipe Installation

FITTING THE APPLIANCE AND CABINET.

1Make suitable arrangements for gas and electrical supplies into the installation site. Preferably a junction box or a 3 pin earthed socket should be situated at the back of the cabinet below the oven.

2Fit cabinet as Fig. 1, making sure that it is level.

3When unpacking the oven keep it on it's polystyrene base until it is put into the cabinet to avoid damage. Do not allow young children to play with any part of the packaging. After installation, please dispose of the packaging with due regard to the environment, your local authority can arrange this.

NOTE: It is imperative that the appliance is left in the base to protect both the appliance and the floor.

4Open Oven door fully.

5Rotate hinge stirrups to there forward position see Fig.2.

6To remove the door, clear the hinges by raising the door slightly whilst pulling towards you.

7Solid gas pipe installation:

i)Remove the gas control knobs, springs, bezels and timer control knobs.

ii)Remove the four screws (two each side) which are visible on the underside of the fascia. Fig. 3.

iii)Tilt the bottom of the fascia panel out over. Withdraw the fascia panel by moving it down over to disengage it from the top fixing lugs. Take care not to lose the two rubber grommets from the timer.

GAS INLET SUPPLY BLOCK

Fig.5

430

120

120

NOTE: The thermostat and grill discs will remain attached to the fascia panel. When refitting the control knobs and bezels, the

drive pins on the rear of the bezel must first be located in the disc carrier. The knob and spring can now be fitted onto the control

spindle. To prevent the top of the fascia panel mounts becoming slack, it may be necessary to adjust the top fixing lugs.

iv)Slacken and remove the union nut on the gas supply elbow on the right hand side of the control panel see Fig.9.

v)Remove the two screws on the gas inlet block Fig.5.

vi)Withdraw the gas inlet block and pipe assembly from the back of the appliance

vii)Remove the union elbow from the inlet block and pipe assembly. The elbow will be required in the final installation.

viii)The union elbow should be connected to the gas supply pipe via a standard ¼"B.S.P. straight connector.

8Install the gas supply pipe on site complete with the union elbow (See Fig.6). Note the orientation of the elbow.

9Position the appliance in front of the cabinet and run the supply cable (See Section 2) through the cabinet and connect to the junction box or socket. Ensure that the supply is isolated at this stage.

41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Operatinginstructions G 8 6 For your safetyIntroduction Contents Location Installing the oven For your safetyCabinet Dimensions Cooling fan for the controls General informationPlease note IgnitionOven light Grill Lighting the oven/grillOven To lightLighting the oven/grill G 8 6 To turn off any burnerHeat control GrillPreheating Cooking positionsPutting food on the grid Grill shelfFor your safety Grill pan is supplied with a removable handle Grill pan and handlePlate warming Heat zones Oven For your safetyOven shelves Condensation Baking trays and dishes For your safetyRoasting Put the dishes in the centre of the shelf Oven cooking chartMins. per ½ kg 1 lb and 25 mins Bread 0.45kg 1lb loaves Joints of meat and poultry Slow cookingFood preparation slow cooking Vegetables G 8 6 Soups, casseroles and stewsMilk puddings Frozen foodsReheating G 8 6 Milk and milk products, for example creamElectronic timer Electronic timerTo set the time of day To use the countdownAutomatic control Setting the controls for automatic useElectronic timer G 8 6 To cancel an automatic programme Hints and tips for automatic cooking Care and cleaning For your safety Oven To remove the outer glass Oven cleaning cycleCleaning between the outer and inner door glass Rust removers Bath/Sink stain removers Cleaning The Door GlassProblem What is wrong and why?Check LCheckG 8 6 Problem Replacing an oven light bulb Replacing an oven light bulbHelp us to help you Service and spare parts For your safetyService Gas Consumers Council Customer care departmentDimensions Technical DataConnections GeneralProvision for Ventilation Important Safety RequirementsOven 560 Hinge Stirrup Fitting the Appliance and CabinetFixing Points Installation Solid Pipe Installation Connection to Electricity Supply 225Green AMP Blue Checking the Grill Pressure TestingRE-ASSEMBLE the Appliance Automatic Operation Checking the Main Oven ControlsChecking the Main Oven Standard guarantee conditions Guarantee Conditions

ZBG 861 specifications

The Zanussi ZBG 861 is a versatile built-in oven that combines modern design with advanced cooking technologies, catering to both novice cooks and culinary enthusiasts. This appliance stands out not only for its functionality but also for its sleek and streamlined appearance, seamlessly blending into any contemporary kitchen.

One of the main features of the ZBG 861 is its generous cooking capacity. With a net volume of around 73 liters, it provides ample space to cook multiple dishes simultaneously. This is particularly useful for large families or when entertaining guests. The oven's interior is designed with a smooth enamel coating, making it easy to clean and maintain, which is a significant advantage for busy households.

The ZBG 861 incorporates a variety of cooking functions to accommodate various culinary needs. With options such as traditional baking, grilling, and even steaming, this oven allows users to explore different cooking methods. One standout feature is the fan-assisted cooking function, which ensures even heat distribution throughout the cavity. This technology not only speeds up cooking time but also helps achieve consistent results, whether baking pastries or roasting meats.

Another noteworthy characteristic of the ZBG 861 is its energy efficiency. This oven is designed with a high energy rating, making it an environmentally friendly choice. It operates on less energy without compromising on performance, reflecting Zanussi's commitment to sustainability.

Safety is also a priority in the design of the ZBG 861. The oven is equipped with an advanced cooling fan system that prevents the exterior from overheating, protecting users from burns. Additionally, the oven includes a child lock feature, providing peace of mind for families with young children.

The digital display and intuitive control panel make managing cooking settings straightforward and user-friendly. Users can easily select cooking programs, adjust temperatures, and set timers, ensuring optimal results every time.

In conclusion, the Zanussi ZBG 861 is a reliable and feature-rich built-in oven that enhances kitchen functionality. With its spacious capacity, diverse cooking functions, energy efficiency, and safety features, it is an excellent addition to any modern kitchen, promising delicious results with every meal.
Top Page Image Contents