Zanussi ZDG 58 manual Fitting the Appliance and Cabinet

Page 40

INSTALLATION Flexible Pipe Installation.

1. FITTING THE APPLIANCE AND CABINET

It is recommended that a 3/8, 1100mm long angled bayonet flexible hose (BFS) and a ½" straight socket (BFS) be used for the installation. However any approved hose of the right length can be used. IMPORTANT: Flexible tubing used must comply with B.S. 669 current editions L.P.G. flexible connections must be of a type suitable for L.P.G. and capable of operation up to 50mbar and carry a red stripe, band or lable.

NOTE:Only liquid sealants can be used in threaded gas connections. Do not use P.T.F.E. tape.

1Make suitable arrangements for gas and electric supplies into the installation site. Preferably a junction box or 3 pin earth socket should be situated at the back of the cabinet below the oven.

2The electrical connection to the appliance is at the rear bottom right hand side, the junction box or socket should be positioned accordingly.

3Fit the cabinet as Fig.1, making sure that it is level.

4When unpacking the appliance keep it on it's polystyrene base until it is put into the cabinet to avoid damage.

5Remove the oven and grill doors

i)Open door fully.

ii)Engage both hinge locking pins (See Fig. 2).

iii)To remove the door, clear the hinges by raising the door slightly whilst pulling towards you.

Fig.2

HINGE

LOCKING PIN

6Remove the fascia panel .

i)Remove the gas control knobs, springs, bezels and timer control knobs.

ii)Remove the four screw (two each side) which are visible on the underside of the fascia. Fig.3.

iii)Tilt the bottom of the fascia panel out over. Withdraw the fascia panel by moving it down over to disengage it from the top fixing lugs. Take care not to lose the two rubber grommets from the timer.

NOTE:The thermostat and grill discs will remain attached to the fascia panel. When refitting the control knobs and bezels, the drive pins on the rear of the bezel must first be located in the disc carrier. The knob and spring can now be fitted onto the control

spindle. To prevent the top fascia panel mounts becoming slack, itFig.3 may be necessary to adjust the top fixing lugs.

5

Page 39 Page 41
Image 40
Page 39 Page 41
Contents
Operatinginstructions Introduction For your safetyG 5 Contents Cabinet Dimensions Installing the oven For your safetyLocation General information Cooling fan for the controlsConnecting to the electricity supply IgnitionOven lights Please noteLighting the oven and grill GrillOven To lightTo turn off any burner Lighting the oven and grill G 5Grill Heat controlPreheating Cooking positionsPutting food on the grid Grill shelf Grill pan and handle Plate warming Oven Heat zonesOven shelves Baking trays and dishes For your safety CondensationThis page has been intentionally left blank Oven cooking chart Put the dishes in the centre of the shelfMins. per ½ kg 1 lb and 25 mins Bread 0.45kg 1 lb loaves Food preparation-slow cooking Slow cookingJoints of meat and poultry G 5 Soups, casseroles and stews VegetablesMilk puddings General points for slow cooking Frozen foodsMilk and milk products, for example cream G 5 LiquidReheating Electronic timer Electronic timer G 5To set the time of day To use the minute minderElectronic timer Setting the controls for automatic useAutomatic control To cancel an automatic programme Hints and tips for automatic cooking Care and cleaning For your safety Oven Oven cleaning cycle Cleaning between the outer and inner door glass To remove the outer glassProblem What is wrong and why?Check G 5 Problem Replacing an oven light bulb Replacing an oven light bulb G 5Service Service and spare parts For your safetyHelp us to help you Customer care department Gas Consumers CouncilZanussi standard guarantee conditions Peace of mind for twenty-four monthsOven 600min Fitting the Appliance and Cabinet Fixing Points Fitting the Appliance and Cabinet Connection to Electricity Supply FIT a 3 AMP Fuse to the Plug Fuse Holder RE-ASSEMBLE the Appliance
Top Page Image Contents