Faber TRATTO Venting Requirements, For More Specific Ductwork INFORMATION, GO

Page 2

VENTING REQUIREMENTS

Determine which venting method is best for your application. Ductwork can extend either through the wall or the roof.

The length of the ductwork and the number of elbows should be kept to a minimum to provide efficient performance. The size of the ductwork should be uniform. Do not install two elbows together. Use duct tape to seal all joints in the ductwork system. Use caulking to seal exterior wall or floor opening around the cap.

Flexibleductworkisnotrecommended. Flexibleductwork creates back pressure and air turbulence that greatly reduces performance.

Make sure there is proper clearance within the wall or floor for exhaust duct before making cutouts. Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be constructed

FOR MORE SPECIFIC DUCTWORK INFORMATION, GO

TO PAGE 4.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

!WARNING

•Venting system MUST terminate outside the home.

•DO NOT terminate the ductwork in an attic or other enclosed space.

•DO NOT use 4" laundry-type wall caps.

•Flexible-type ductwork is not recommended.

•DO NOT obstruct the flow of combustion and ventilation air.

•Failure to follow venting requirements may result in a fire.

ELECTRICAL REQUIREMENTS

A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit. A time-delay fuse or circuit breaker is recommended. The fuse must be sized per local codes in accordance with the electrical rating of this unit as specified on the serial/rating plate located inside the unit near the field wiring compartment. THIS UNIT MUST BE CONNECTED WITH COPPER WIRE ONLY. Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 - latest edition, and all local codes and ordinances. Wire size and connections must conform with the rating of the appliance. Copies of the standard listed above may be obtained from:

National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

For residential use only.

This appliance should be connected directly to the fused disconnect (or circuit breaker) through flexible, armored or nonmetallic sheathed copper cable. Allow some slack in the cable so the appliance can be moved if servicing is ever nec- essary. A UL Listed, 1/2" conduit connector must be provided at each end of the power supply cable (at the appliance and at the junction box).

When making the electrical connection, cut a 1 1/4" hole in the wall. A hole cut through wood must be sanded until smooth. A hole through metal must have a grommet.

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this fan with any solid-state speed control device.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRI- CAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.

Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or Explosive Materials and Vapors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRI- CAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:InstallationWorkAndElectricalWiringMust Be Done By Qualified Person(s) In Accordance With All Applicable Codes And Standards, Including Fire-Rated Construction.

Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer's guideline and safety standards such as those published by the National Fire ProtectionAssociation (NFPA), and theAmerican Society for Heating, Refrigeration andAir Conditioning Engineers (ASHRAE), and the local code authorities.

When cutting or drilling into wall or ceiling, do not dam- age electrical wiring and other hidden utilities.

Ducted fans must always be vented to the outdoors.

!WARNING

•Electrical ground is required on this rangehood.

•If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO NOT use for grounding.

•DO NOT ground to a gas pipe.

•DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding circuit could result in electrical shock.

•Check with a qualified electrician if you are in doubt as to whether the rangehood is properly grounded.

•Failure to follow electrical requirements may result in a fire.

Version 04/05 - Page 2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Lisez Bien Cette Fiche Avant Dinstaller LA Hotte TrattoElectrical Requirements Venting RequirementsFor More Specific Ductwork INFORMATION, GO For residential use onlyAvertissement Pour Minimiser LES Risques Règlements DévacuationFiche Technique Électrique CORPORELS, Observer LES PrescriptionsHardware Package Literature Package Plan the InstallationPersonal Injury Hazard FeetCanopy Vented to the outside8 min Upper Cabinet baseHood and the cooktop distance Not vented to the outside10 min Proceed to for ALL Installations on Next Prepare the WallDiverter Extension For Ductless InstallationsFor ALL Installations Warranty & Service USE and Care InformationPlan DE LʼINSTALLATION Risque DE BlessureCouvercle cheminée Dimensions DʼINSTALLATION Avec ConduitCheminée Plafond Haut HotteDimensions DʼINSTALLATION Sans Conduit Dextension Pour La Cheminée Plafond HautPréparation DU MUR Installation DE LA HotteProcéder À Pour Tout LES Installations VIS DE FixationsInstaller le Filtre AU Charbon 6 de la Figure Installations Sans ConduitPour Tout LES Installations Ductless DiverterUtilisation ET Entretien

TRATTO specifications

Faber TRATTO is a modern kitchen hood that combines cutting-edge technology with sleek design, aimed at enhancing the cooking experience while maintaining a stylish aesthetic. This appliance is not just a functional necessity but also a design statement in contemporary kitchens.

One of the standout features of Faber TRATTO is its advanced filtration system. It utilizes a combination of aluminum filters and a high-performance motor to efficiently capture grease, smoke, and odors produced during cooking. The multi-layered filtration aids in maintaining indoor air quality, ensuring that your kitchen remains fresh and inviting.

Faber TRATTO is equipped with a powerful ventilation system that can handle high-volume cooking with ease. The hood's powerful extraction rates mean it can quickly clear the air, making it particularly beneficial for those who love to cook elaborate meals or use strong spices. With noise reduction technology, the TRATTO operates quietly, allowing for comfortable conversation even during meal preparation.

Another remarkable feature of the TRATTO is its energy efficiency. Designed to be environmentally friendly, it includes LED lighting that not only illuminates the cooking area but also consumes significantly less energy compared to traditional light fixtures. This results in cost savings on electricity bills and a lower carbon footprint.

The user-friendly controls of the Faber TRATTO further enhance its appeal. It features intuitive touch controls that allow for easy operation of the hood's settings, including speed adjustments and lighting. Additionally, many models offer smart connectivity, enabling users to control the hood remotely via a smartphone app.

The design of Faber TRATTO stands out with its minimalist aesthetic, available in various finishes that blend seamlessly with any kitchen décor. Whether you opt for a stainless steel finish or a more contemporary black model, the TRATTO adds a touch of elegance to your space.

In summary, Faber TRATTO is an exceptional kitchen hood that combines powerful performance, energy efficiency, and a modern design. With its advanced filtration system, quiet operation, user-friendly controls, and stylish appearance, it is an indispensable addition to any kitchen, enhancing both functionality and style.
Top Page Image Contents