Faber TRATTO For Ductless Installations, For ALL Installations, Diverter Extension

Page 8

1.LOWER CHIMNEY DUCTLESS

2.LEFT VENT GRID

3.RIGHT VENT GRID

4.DIVERTER EXTENSION HORIZONTAL (2 PIECES)

5.DUCTLESS DIVERTER

6.CHARCOAL FILTER

FIGURE 8

FOR DUCTLESS INSTALLATIONS

Ductless installations require a Ductless Conversion Kit whose components are pictured in FIGURE 8. Do not use the DAMPER (H in FIGURE 1) for ductless installations. The LOWER CHIMNEY COVER (B in FIGURE 1) should be discarded and replaced by a new one with holes (1 in FIGURE 8).

1.As indicated in FIGURE 8, fit the DUCTLESS DIVERTER

(5) over the duct outlet. Fit the 2 DIVERTER EXTENSION HORIZONTAL pieces (4) on either side of the DUCTLESS DIVERTER.

2. Install the CHARCOALFILTER (6) behind the center grease filter opening by inserting and locking into place, as indicated in FIGURE 9.

FIGURE 9

FOR ALL INSTALLATIONS

1.Remove the cover from the Field Wiring Compartment with a phillips screwdriver. Feed the Power Supply Cable through the electrical knockout. Connect the Power Supply Cable to the range- hood cable. Attach the Power Supply Cable grounding lead to the green screw provided. Attach the White lead of the power supply to the White lead of the rangehood with a twist-on type wire con- nector. Attach the Black lead of the power supply to the Black lead of the rangehood with a twist-on type wire connector. Using the 4 holes provided screw the Field Wiring Compartment to the wall as dictated by your Power Supply Cable location (screws not provided). Replace the cover.

2.Install the UPPER CHIMNEYCOVER (CinFIGURE10)by slightly widening the two sides and hooking them behind the CHIMNEY MOUNTING BRACKETS (E). Secure the sides to the CHIMNEY MOUNTING BRACKETS with the 4 CHIMNEY SCREWS (G).

3.Install the LOWER CHIMNEY COVER (B) by slightly widening the two sides of the LOWER CHIMNEY COVER and hooking them between the UPPER CHIMNEY COVER and the wall making sure that it fits snugly. Secure the LOWER CHIMNEY COVER to the CANOPY SECTION (A) with 2 CHIMNEY SCREWS (G).

FIGURE 10

FOR DUCTLESS

 

INSTALLATIONS

 

Fit the LEFT AND RIGHT

 

VENT GRIDS (2 and 3)

 

into the LOWER CHIMNEY

 

DUCTLESS holes, making

 

sure that the directional

 

symbols are towards the top

 

andfrontofthehoodandthat

 

they connect snugly to the

 

DIVERTER EXTENSION

FIGURE 11

HORIZONTAL pieces.

 

Version 04/05 - Page 8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Lisez Bien Cette Fiche Avant Dinstaller LA Hotte TrattoVenting Requirements For More Specific Ductwork INFORMATION, GOElectrical Requirements For residential use onlyRèglements Dévacuation Fiche Technique ÉlectriqueAvertissement Pour Minimiser LES Risques CORPORELS, Observer LES PrescriptionsPlan the Installation Personal Injury HazardHardware Package Literature Package FeetVented to the outside 8 min UpperCanopy Cabinet baseHood and the cooktop distance Not vented to the outside10 min Proceed to for ALL Installations on Next Prepare the WallDiverter Extension For Ductless InstallationsFor ALL Installations Warranty & Service USE and Care InformationPlan DE LʼINSTALLATION Risque DE BlessureDimensions DʼINSTALLATION Avec Conduit Cheminée Plafond HautCouvercle cheminée HotteDimensions DʼINSTALLATION Sans Conduit Dextension Pour La Cheminée Plafond HautInstallation DE LA Hotte Procéder À Pour Tout LES InstallationsPréparation DU MUR VIS DE FixationsInstallations Sans Conduit Pour Tout LES InstallationsInstaller le Filtre AU Charbon 6 de la Figure Ductless DiverterUtilisation ET Entretien

TRATTO specifications

Faber TRATTO is a modern kitchen hood that combines cutting-edge technology with sleek design, aimed at enhancing the cooking experience while maintaining a stylish aesthetic. This appliance is not just a functional necessity but also a design statement in contemporary kitchens.

One of the standout features of Faber TRATTO is its advanced filtration system. It utilizes a combination of aluminum filters and a high-performance motor to efficiently capture grease, smoke, and odors produced during cooking. The multi-layered filtration aids in maintaining indoor air quality, ensuring that your kitchen remains fresh and inviting.

Faber TRATTO is equipped with a powerful ventilation system that can handle high-volume cooking with ease. The hood's powerful extraction rates mean it can quickly clear the air, making it particularly beneficial for those who love to cook elaborate meals or use strong spices. With noise reduction technology, the TRATTO operates quietly, allowing for comfortable conversation even during meal preparation.

Another remarkable feature of the TRATTO is its energy efficiency. Designed to be environmentally friendly, it includes LED lighting that not only illuminates the cooking area but also consumes significantly less energy compared to traditional light fixtures. This results in cost savings on electricity bills and a lower carbon footprint.

The user-friendly controls of the Faber TRATTO further enhance its appeal. It features intuitive touch controls that allow for easy operation of the hood's settings, including speed adjustments and lighting. Additionally, many models offer smart connectivity, enabling users to control the hood remotely via a smartphone app.

The design of Faber TRATTO stands out with its minimalist aesthetic, available in various finishes that blend seamlessly with any kitchen décor. Whether you opt for a stainless steel finish or a more contemporary black model, the TRATTO adds a touch of elegance to your space.

In summary, Faber TRATTO is an exceptional kitchen hood that combines powerful performance, energy efficiency, and a modern design. With its advanced filtration system, quiet operation, user-friendly controls, and stylish appearance, it is an indispensable addition to any kitchen, enhancing both functionality and style.
Top Page Image Contents