Faber TRATTO installation instructions USE and Care Information, Warranty & Service

Page 9

FOR ALL INSTALLATIONS

1.Install the grease filters using two hands by first pulling and turning the knob to the left so that the locking lever does not protrude from the filter (as in FIGURE 12). Insert the opposite end of the filter into the retaining channel. Insert the knob end next, then turn knob to the right to lock the filter into place.

FIGURE 12

2.Turn the power supply on. Turn on blower and lights. If the rangehood does not operate, check that the circuit breaker is not tripped or the house fuse blown. If the unit still does not operate, disconnect the power supply and check that the wiring connec- tions have been made properly.

WIRING DIAGRAM

•This rangehood uses 20 watt halogen lamps.

USE AND CARE INFORMATION

This rangehood system is designed to remove smoke, cooking vapors and odors from the cooktop area.

For Best Results

Starttherangehoodseveralminutesbeforecookingtodevelopproper airflow. Allow the unit to operate for several minutes after cooking is complete to clear all smoke and odors from the kitchen.

Rangehood Control Panel

The control panel is located on the front edge of the rangehood canopy. The position and function of each control button are indicated in FIGURE 13.

Light On/Off Button ( L )

On/Off switch for the halogen lights. Push the button in to turn the light ON, push again to turn the light OFF.

FIGURE 13

Blower Indicator

Light ( I )

Lights up to indicate blower is ON.

Blower On/Off and Speed Buttons ( 1, 2, 3 )

Push button (1) to turn ON and OFF the blower. This button must be pushed in for the blower to operate regardless of speed chosen. Button (1) operates the blower on LOW speed. Push button (2) for MEDIUM speed. Push button (3) for HIGH speed.

Cleaning

Thestainlesssteelgreasefiltersshouldbecleanedfrequentlyin hot detergent solution or washed in the dishwasher. Stainless steel cleaner should be used on stainless rangehoods. Abrasives and scouring agents can scratch stainless steel finishes and should not be used to clean finished surfaces.

Replacing the Lamps

Remove the snap-on lamp cover (as indicated in figure 16) by levering it from under the metal ring, supporting it with one hand. Remove the halogen lamp from the lamp holder by pulling gently. Replace the lamp with a new one of the same type, making sure that you insert the two pins properly into the housings on the lamp holder. Replace the snap-on lamp cover.

FIGURE 16

WARRANTY & SERVICE

All Faber products are warranteed against any defect in ma- terials or workmanship for the original purchaser for a period of 1 year from the date of original purchase. This warranty covers labor and replacement parts. The warranty does not cover consumable parts such as filters and light bulbs. This warranty does not apply if this product has been subjected to faulty installation, misuse, or neglect. This warranty excludes any consequential expense or damage resulting from any use or malfunction of the product. All implied warranties are limited to the duration of this warranty.

To obtain warranty service, contact the dealer from whom you purchased the rangehood, or the local Faber distributor. If you cannot identify a local Faber distributor, contact us at (508) 358-5353 for the name of a distributor in your area.

Version 04/05 - Page 9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Tratto Lisez Bien Cette Fiche Avant Dinstaller LA HotteFor More Specific Ductwork INFORMATION, GO Venting RequirementsElectrical Requirements For residential use onlyFiche Technique Électrique Règlements DévacuationAvertissement Pour Minimiser LES Risques CORPORELS, Observer LES PrescriptionsPersonal Injury Hazard Plan the InstallationHardware Package Literature Package Feet8 min Upper Vented to the outsideCanopy Cabinet baseNot vented to the outside 10 minHood and the cooktop distance Prepare the Wall Proceed to for ALL Installations on NextFor Ductless Installations For ALL InstallationsDiverter Extension USE and Care Information Warranty & ServiceRisque DE Blessure Plan DE LʼINSTALLATIONCheminée Plafond Haut Dimensions DʼINSTALLATION Avec ConduitCouvercle cheminée HotteDextension Pour La Cheminée Plafond Haut Dimensions DʼINSTALLATION Sans ConduitProcéder À Pour Tout LES Installations Installation DE LA HottePréparation DU MUR VIS DE FixationsPour Tout LES Installations Installations Sans ConduitInstaller le Filtre AU Charbon 6 de la Figure Ductless DiverterUtilisation ET Entretien

TRATTO specifications

Faber TRATTO is a modern kitchen hood that combines cutting-edge technology with sleek design, aimed at enhancing the cooking experience while maintaining a stylish aesthetic. This appliance is not just a functional necessity but also a design statement in contemporary kitchens.

One of the standout features of Faber TRATTO is its advanced filtration system. It utilizes a combination of aluminum filters and a high-performance motor to efficiently capture grease, smoke, and odors produced during cooking. The multi-layered filtration aids in maintaining indoor air quality, ensuring that your kitchen remains fresh and inviting.

Faber TRATTO is equipped with a powerful ventilation system that can handle high-volume cooking with ease. The hood's powerful extraction rates mean it can quickly clear the air, making it particularly beneficial for those who love to cook elaborate meals or use strong spices. With noise reduction technology, the TRATTO operates quietly, allowing for comfortable conversation even during meal preparation.

Another remarkable feature of the TRATTO is its energy efficiency. Designed to be environmentally friendly, it includes LED lighting that not only illuminates the cooking area but also consumes significantly less energy compared to traditional light fixtures. This results in cost savings on electricity bills and a lower carbon footprint.

The user-friendly controls of the Faber TRATTO further enhance its appeal. It features intuitive touch controls that allow for easy operation of the hood's settings, including speed adjustments and lighting. Additionally, many models offer smart connectivity, enabling users to control the hood remotely via a smartphone app.

The design of Faber TRATTO stands out with its minimalist aesthetic, available in various finishes that blend seamlessly with any kitchen décor. Whether you opt for a stainless steel finish or a more contemporary black model, the TRATTO adds a touch of elegance to your space.

In summary, Faber TRATTO is an exceptional kitchen hood that combines powerful performance, energy efficiency, and a modern design. With its advanced filtration system, quiet operation, user-friendly controls, and stylish appearance, it is an indispensable addition to any kitchen, enhancing both functionality and style.
Top Page Image Contents