Elitair PN-36 manual Englishgb, General, Safety Precaution, Installation Instructions

ENGLISHGB

GENERAL

Carefully read the following important information regarding installation safety and maintenance. Keep this information booklet accessible for further consultations.

The appliance has been designed for use in the ducting version (air exhaust to the outside), filtering version (air circulation on the inside).

SAFETY PRECAUTION

1.Take care when the cooker hood is operating simultaneously with an open fireplace or burner that depend on the air in the environment and are supplied by other than electrical energy, as the cooker hood removes the air from the environment which a burner or fireplace need for combustion. The negative pressure in the environment must not exceed 4Pa (4x10-5 bar). Provide adequate ventilation in the environment for a safe operation of the cooker hood.

Follow the local laws applicable for external air evacuation.

2.WARNING !

In certain circumstances electrical appliances may be a danger hazard.

A)Do not check the status of the filters while the cooker hood is operating

B)Do not touch the light bulbs after appliance use

C)Flambè cooking is prohibited underneath the cooker hood

D)Avoid free flame, as it is damaging for the filters and a fire hazard

E)Constantly check food frying to avoid that the overheated oil may become a fire hazard

F)Disconnect the electrical plug prior to any maintenance.

G)This appliance is not intended for use by young children or infirm persons without supervision

H)Young children should be supervised to ensure they do not play with the appliance

I)There shall be adequate ventilation of the room when the rangehood is used at the same time as

appliances burning gas or other fuels

L)There is a risk of fire if cleaning is not carried out in accordance with the instructions

INSTALLATION INSTRUCTIONS

• Electric Connection

The appliance has been manufactured as a class II, therefore no earth cable is necessary.

The connection to the mains is carried out as follows: BROWN = L line

BLUE = N neutral

If not provided, connect a plug for the electrical load indicated on the description label. Where a plug is provided, the cooker hood must be installed in order that the plug is easily accessible.

An omnipolar switch with a minimum aperture of 3mm

between contacts, in line with the electrical load and local standards, must be placed between the appliance and the network in the case of direct connection to the electrical network.

•The appliance must be installed at a minimum height of 650 mm from an cooker stove in case of a gashob or an electrical hob.

If a connection tube composed of two parts is used, the upper part must be placed outside the lower part.

Do not connect the cooker hood exhaust to the same conductor used to circulate hot air or for evacuating fumes from other appliances generated by other than an electrical source.

•MOUNTINGOFTHEHOODINTHELOWERPARTOFAN HANGINGCUPBOARD

Drill 4 holes of 6 mm. diameter at the bottom of the hanging cupboard as showed in the drawing fig.3.

Fit the hood in the cabinet with 4 screws, which are appropriate to that kind of cupboard.

The appliance is provided with 2 air outlets, one which is in the upper part and the other on the back. Both of them can be used according to your requirements. A connecting ring (C), which to join the connecting pipe to,and a cover

(A)to close the air outlet, which is not used, are supplied.

•MOUNTING OF THE HOOD IN THE WALL

Make 4 holes (B-P) according to the measurements indicated in fig. 2.

For the various assembly operations, use screws and anchors suitable for the type of wall (eg., concrete, plasterboard, etc.)

Hang the hood on the wall using the two holes (B) fig. 2. Secure the hood to the wall using the two lower safety holes

(P).

•MOUNTING OF THE HOOD ON THE WALL

Drill 2 holes on the wall, which correspond to the position

(B) of the drawing fig. 1.

Hang the hood on the 2 holes by using the screws and dowels with expanding plug ,which are aprropriate for that kind of wall (ex. concrete, plasterboard etc.)

Fix definitely the hood through the 2 security holes (Z).

•FITTING THE PIPES (OPTIONAL)

Make four holes (G-H) according to the measurements indicated in fig. 2

For the various assembly operations, use screws and anchors suitable for the type of wall (eg., concrete, plasterboard, etc.)

Secure the bracket (Z) to the wall fig. 2 Position the two pipes vertically on the hood. Hang the pipe fitting (F) using the 2 holes (H) fig. 2 Remove pipe fitting (E) from fitting (F) and secure to the side of the bracket (Z) with the screws provided.

•FITTING THE GLASS SECTION (OPTIONAL) Position the glass section complete with supports (V) as indicated in fig. 1 and secure to the hood using the screws provided.

- 7 -