Hearth and Home Technologies GNBC36, GNBC30, GNBC33 manual Junction BOX Installation Instructions

Page 13

NOVUS B-VENT INSTALLATION INSTRUCTIONS

c.Intermittent Pilot Ignition

This appliance is equipped with an intermittent pilot control valve which operates on a 3 volt system. See wiring diagram, Figure 15.

The appliance is supplied with a battery pack and a 3 volt AC transformer, which requires the installation of the supplied junction box. It is highly recommended that the junction box be installed at this time to avoid reconstruction. The battery pack requires two D cell batteries (not included). Batteries cannot be placed in the battery pack while using the 3 volt AC transformer. Conversely, the transformer must be unplugged if the battery pack is used.

Note: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electric Code, CSA C221.1.

CAUTION:

Battery polarity must be correct or control module damage will occur.

Figure 15 - Intermittent Pilot Ignition Diagram

d.Junction Box Wiring

We recommend you operate the two outlets on separate circuits, one side hot full time, one side switched. This allows independent operation of the appliance and fan. Independent operation is obtained by using minimum 14-3 with ground Romex and separating the two outlets by breking out the tab as shown in Figure 16.

6.JUNCTION BOX INSTALLATION INSTRUCTIONS

a.Remove the junction box assembly from the valve compartment.

b.If the box is being wired from the OUTSIDE of the appliance:

1)Loosen two screws on the Romex connector, feed the necessary length of wire through the connector and tighten the screws.

2)Make all necessary wire connections to the receptacle and assemble the receptacle and cover to the junction box.

Figure 16 - Junction Box Detail

3)Attach the junction box assembly to the outside of the appliance with the two screws provided.

c.If the box is being wired from the INSIDE of the appliance:

1)Pull the electrical wires from outside the appliance through this opening into the valve compartment.

2)Loosen the two screws on the Romex connector, feed the necessary length of wire through the connector and tighten the screws.

3)Make all necessary wire connections to the receptacle and assemble the receptacle and cover to the junction box.

4)Attach the junction box assembly to the inside of the appliance with the two screws provided.

d.If the box is not to be wired at the time of appliance installation, assemble the receptacle and cover to the box and install on the inside of the appliance.

12-02

13

34615 Rev G

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Do not expose appliance to the elements such as rain, etc Novus Series Vent GAS ApplianceTable of Contents Design and Installation Considerations for B-VENTS Typical Vertical Installation Applicance SpecificationsGlass SPECIFICATIONS/CERTIFICATIONS S. and Canada CertificationAppliance Dimensions Installation ComponentLocation and Clearances Novus NomenclatureFraming Wear gloves and safety glasses for protectionAppliance Locations and Space Requirements ClearancesVenting Setting the ApplianceVent Height Attaching VentingCHASE/TERMINATION Installation Firestop SPACER/VENT InstallationInstalling the Firestop Spacer Testing Ventilation Installing AN Outside AIR KIT Strongly RecommendedCheck Venting System Vent Height for Vertical Termination Roof Pitch Min. FtOutside Air Locations Novus UtilitiesWall Switch WiringIntermittent Pilot Ignition Junction BOX Installation InstructionsAppliance Preparation FinishingAppliance Preparation Determining the Ignition TypeLog Set Placing the Rock WoolIntermittent Pilot Ignition Lighting Instructions Lighting InstructionsTo Turn OFF the GAS to the Appliance Intermittent Pilot IgnitionStanding Pilot Ignition To Turn OFF the GAS to ApplianceBefore Operating this Appliance have Qualified Technician Seasonal ChecklistStanding Pilot Ignition Operation Intermittent Pilot Ignition OperationOutside AIR KIT Operation START-UP IssuesCleaning the Burner and Control Compartment Maintenance InstructionsChecking Flame Patterns LOG REMOVAL/REPLACEMENT Cleaning the GlassVenting System Inspection Optional Components Intermittent Pilot Conversion Kits Robertshaw Standing Pilot Conversion KitsBay Door Trim Kit Trim KitsQuick Tile Brass Surround Item # Description Qty Replacement PartsHomeowner’s Notes Index Year Limited Warranty Limited Lifetime WarrantyHow to Obtain Service Conditions, Exclusions, & Limitations of Liability

GNBC33, GNBC36, GNBC30 specifications

Hearth and Home Technologies (HHT) has established itself as a leading manufacturer of innovative and efficient hearth products, and its GNBC series of gas fireplaces – specifically the GNBC30, GNBC33, and GNBC36 – exemplifies this commitment to quality and performance. Each model in this series is designed to combine elegance with cutting-edge technology, ensuring a warm and inviting atmosphere in any home.

One of the main features of the GNBC series is its versatile design. These models are built to be multi-sided, offering a view of the flames from various angles, making them ideal centerpieces for both modern and traditional home interiors. The GNBC30, GNBC33, and GNBC36 showcase a minimalist aesthetic, available in multiple finishes and configurations, allowing homeowners to customize their spaces to reflect their personal style and preferences.

Efficiency is a crucial aspect of these gas fireplaces. The GNBC series utilizes advanced gas technology to provide clean and efficient heating, with a focus on maximizing warmth while minimizing energy consumption. These fireplaces are also equipped with smart electronic ignition systems, which enhance convenience and promote energy efficiency. By utilizing a thermostat, users can maintain their desired temperature effortlessly.

Safety is a top priority for HHT, and the GNBC series incorporates numerous safety features. The models come standard with a glass front and built-in safety screens, significantly reducing the risk of burns and accidents. Additionally, they feature a durable construction designed to last, ensuring that these fireplaces remain a safe and effective source of heat for years to come.

Another notable characteristic of the GNBC series is the ease of installation. Designed with the homeowner in mind, these fireplaces are relatively simple to integrate into a variety of architectural settings. The GNBC models can be vented through either natural ventilation or direct vent systems, allowing for greater flexibility based on the specific needs of the home.

In summary, Hearth and Home Technologies' GNBC30, GNBC33, and GNBC36 gas fireplaces offer a unique blend of style, technology, and safety. With their modern aesthetics, excellent efficiency ratings, and exceptional safety features, these fireplaces are an excellent choice for those seeking to enhance their living spaces while enjoying the benefits of a reliable heating source. Whether for new construction or renovation projects, the GNBC series stands out as a premier option for homeowners looking to elevate their hearth experience.
Top Page Image Contents