Zanussi ZDT 5053 manual Water outlet hose connection, Electrical connection, Proceed as follows

Page 19

Water outlet hose connection

The end of the drain hose can be connected in the following ways:

1.To the sink outlet spigot, securing it to the underside of the work surface. This will prevent waste water from the sink running into the machine.

2.Hooked over the edge of the sink using the special curved plastic guide (if provided with the machine).

3.To a stand pipe provided with vent-hole, minimum internal diameter 4 cm.

The waste connection must be at a height of between 30 cm (minimum) and 100 cm (maximum) from the bottom of the dishwasher.

The drain hose can face either to the right or left of the dishwasher

Ensure the hose is not bent or squashed as this could prevent or slow down the discharge of water.

The sink plug must not be in place when the machine is draining as this could cause the water to syphon back into the machine.

If you use a drain hose extension it must be no longer than 2 metres and its internal diameter must be no smaller than the diameter of the hose provided.

Likewise the internal diameter of the couplings used for connections to the waste outlet must be no smaller than the diameter of the hose provided.

Attention!

Our appliances are supplied with a security device to protect against the return of dirty water back into the machine.

If the spigot of your sink has a "no return valve" incorporated this can prevent the correct draining of your dishwasher. We advise you therefore to remove it.

Electrical connection

This appliance must be earthed.

The manufacturer declines any responsibility should this safety measure not be observed.

If the plug that is fitted to your appliance is not suitable for the socket, it must be cut off and the appropriate plug fitted.

Important

The wires on the mains lead are coloured in accordance with the following code:

Green and Yellow - Earth

Blue- Neutral

Brown- Live

If you fit your own plug, the colours of the wires in the mains lead of your appliance may not correspond with the markings identifying the terminals in your plug.

Proceed as follows:

1.Connect the Green and Yellow (earth) wire to the terminal

in the plug which is marked with the letter "E" or the earth

symbol or coloured green and yellow.

2.Connect the Blue (neutral) wire to the terminal in the plug which is marked with the letter "N" or coloured black.

3.Connect the Brown (live) wire to the terminal in the plug which is marked with the letter "L" or coloured red.

The plug moulded onto the lead incorporates a 13amp BSI362 fuse. Only ASTA or BSI fuses should be used.

The plug must not be used if the fuse cover/carrier is lost. The cover/carrier is indicated by the coloured insert at the base of the plug.

A replacement cover/carrier must be obtained from your local Service Force Centre.

To isolate the dishwasher from mains, remove the mains plug.

Important!

The plug must still be accessible after the appliance has been installed.

The appliance should not be connected to the electrical supply by means of an extension cable.

In case that the electrical cable has to be replaced, please contact your local Service Force Centre.

Warning!

A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that it is disposed of safely.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Dishwasher Contents Disposal Safety instructionsInstallation Child safetyDescription of the appliance Programme indicator lights Audible signalsDeactivation/activation of the audible signals Water softener Prior to using for the first timeSetting manually Setting electronicallyFilling with rinse aid Adjusting the doseFilling with dishwasher salt Rinse aidCutlery basket Daily useLoading cutlery and dishes Lower basketTo move to the higher position proceed as follows Adjusting the height of the upper basketUpper basket Use of detergentConcentrated detergent Different kinds of detergentDetergent tablets Use of 3 in 1 combi detergentsQuick 30 MIN Washing programmesDegree of soil Cycle description Consumption values Type of loadUnloading the dishwasher To interrupt or cancel a washing programme in progressStarting a washing programme End of the washing programmeProlonged periods of non-operation Maintenance and cleaningCleaning the filters Frost precautionsMalfunction Possible cause Solutions Fault code appearsThere are problems when operating the dishwasher Fault code / malfunction Possible cause SolutionsWater drops have dried onto glasses and dishes Dishes are not cleanWash results are not satisfactory Dishes are wet and dullCustomer Care Department Service and Spare PartsExclusions Guarantee ConditionsStandard guarantee conditions European GuaranteeFixing to the adjacent units Installation instructionsBuilding-in LevellingProceed as follows Water outlet hose connectionElectrical connection Green and Yellow Earth Blue- Neutral Brown- LiveCup racks position a Hints for test centresPage Page Page From the Electrolux Group. The World’s No.1 choice

ZDT 5053 specifications

The Zanussi ZDT 5053 is a modern and efficient integrated dishwasher designed to elevate your kitchen experience. With its sleek design and innovative technology, it seamlessly blends into any kitchen décor while providing superior cleaning performance.

One of the standout features of the ZDT 5053 is its generous capacity. With room for up to 13 place settings, it is ideal for families or those who frequently entertain guests. The adjustable racks and tines provide flexible loading options, accommodating larger items such as pots, pans, and baking sheets without difficulty. This thoughtful design ensures that every dish, cutlery, and glass comes out sparkling clean.

Another key aspect of the Zanussi ZDT 5053 is its A+ energy efficiency rating. This not only helps to reduce your carbon footprint but also lowers energy bills, making it an environmentally friendly choice for conscientious consumers. The dishwasher combines performance with eco-friendly technology, ensuring that it uses water and electricity efficiently. The Eco Programme is specifically designed to reduce water and energy consumption, ensuring that you can maintain a sustainable kitchen without sacrificing performance.

The ZDT 5053 also boasts various wash programs tailored to meet different cleaning needs. Among these options are intensive wash cycles for heavily soiled pots and dishes, as well as quick wash settings for those times when you need clean dishes in a hurry. The quick 30-minute wash is particularly convenient for busy households, ensuring that you never run out of clean cutlery and plates during meal preparations or gatherings.

In terms of noise level, the Zanussi ZDT 5053 operates quietly, making it suitable for open-plan living spaces. The low noise output ensures that you can run the dishwasher at any time without disturbing your household activities.

Additionally, the dishwasher features a delay start option, allowing you to set the cleaning cycle to begin at a more convenient time. This adds flexibility to your daily routine, so you can take advantage of cheaper energy rates during off-peak hours if desired.

Overall, the Zanussi ZDT 5053 combines space, efficiency, and performance, making it an excellent choice for anyone looking to enhance their kitchen with a reliable dishwasher. Its combination of innovative features and energy-efficient operation ensures that it stands out in its class, bringing convenience and cleanliness to your home.
Top Page Image Contents