Problem
Possible solution
The grill, ovens and timer do not work. | • Check that the appliance has been wired in to the |
|
| appliance supply and is switched on at the wall. |
|
| • Check that the main appliance fuse is working. |
|
| • If you have checked the above: Allow the appliance |
|
| to cool for a couple of hours. The appliance should |
|
| now be working normally. |
|
|
|
|
The grill and top oven work but the main oven does not. | • Check that the time of day has been set on the clock. |
|
|
|
|
The timer does not work. | • Check that the instructions for the operation of the |
|
| timer are being closely followed. |
|
The oven is not cooking evenly. | • Check that the appliance is correctly installed and |
|
| is level. |
|
| • Check that the recommended temperatures and |
|
| shelf positions are being used. |
|
|
|
|
The indicator neons are not working correctly. | • Check that you have selected only the function you |
|
| require. Ensure all other controls are in the off position. |
|
The oven fan is noisy. | • Check that the oven is level. |
|
| • Check that the shelves and bakeware are not vibrating |
|
| in contact with the oven back panel. |
|
| m |
|
| ||
|
| |
The oven temperature is too high or too low. | • Check that the recommended temperatures and | |
| shelf positions are being used. Be prepared to adjust | |
| the temperature up or down to achieve the | |
| results you want. | |
|
|
|
Installation |
|
|
| |||
Installation instructions |
| freestanding and can be fitted with cabinets on one | ||||
| ||||||
| ! WARNING! |
|
| or both sides. | ||
|
|
|
|
| • | Sidewalls, which are above hob level, should be |
This appliance must be earthed. |
| |||||
|
| protected by heat resistant | ||||
|
|
|
|
|
| |
• If your appliance has been damaged in transit, |
|
| material and must not be nearer than 40mm to the | |||
| contact your supplier immediately. Do not attempt |
|
| hob side. | ||
| to install it. |
| • A nominal air gap of 5mm at either side of the | |||
|
|
| appliance is required to enable the appliance to be | |||
• Your appliance left the factory fully packaged to |
|
| ||||
| protect it from damage. If it is delivered without |
| • | moved into position. | ||
| packaging and damage has occurred, the |
| Always ensure an air gap is maintained at hotplate | |||
|
|
| level. Tiles or other forms of deep wall covering | |||
| manufacturer cannot accept responsibility. Contact |
|
| |||
|
|
| should not obscure this gap. | |||
| your supplier for advice. |
|
| |||
• | Once the packaging has been removed the |
| • | Overhanging surfaces or a cooker hood should be | ||
|
| a minimum of 685mm above the hob. | ||||
| appliance should only be moved by hand. Do not |
|
| |||
|
| • | It is important to ensure that the appliance is level | |||
| use a sack barrow or any other aid to lift the |
| ||||
|
|
| after installation. Levelling feet are fitted to the | |||
| appliance as damage may occur. Do not carry the |
|
| |||
|
|
| appliance to accommodate uneven floors. | |||
| appliances at the doorhandle. |
|
| |||
• | To move the appliance, open the oven door and lift |
| Adjustment of levelling feet | |||
| the appliance by holding inside the top of the |
| ||||
|
| The cooker stands on 4 levelling feet. It is required to | ||||
| compartment. |
| ||||
• | This is a type X appliance, which means it is |
| confirm the appliance is correctly levelled before | |||
|
|
|
|
|
|
|
19