Sherwood R-872 manual Remote Control Operation Range

Page 20

ENGLISH

OPERATING COMPONENTS WITH REMOTE CONTROL

1. Enter the setup code for each component other

than this receiver. For details, refer to "Entering a setup code" on page 21.

2. Turn on the component you want to operate.

3. Press the DEVICE button on the remote control

corresponding to the component you wish to operate.

4. Aim the remote control at the REMOTE

SENSOR of the component you wish to control and press the button corresponding to the operation you want.

■Notes :

•When you cannot operate any component, check if the transmission signal mode is set to "RF". (For details, refer to "Changing the transmission signal" on page 29.)

•In this case, to operate the component, connect the IR emitter to the IR OUT jack and use the remote control toward this receiver. (For details, refer to "CONNECTING RF REMOTE ANTENNA" and "CONNECTING MULTI- ROOM SYSTEM KIT" on page 14.)

REMOTE CONTROL OPERATION RANGE

■In case that this remote control emits the infrared beams

•Use the remote control within a range of about 7 meters (23 feet) and angles of up to 30 degrees aiming at the remote sensor.

■In case that this remote control emits the RF beams

•Use the remote control within a distance of about 15 meters (50 feet) toward this receiver.

LOADING BATTERIES

•When the remote control does not operate, the old batteries should be replaced. In this case, load new batteries within several minutes after removing old batteries.

•If the batteries are removed or have been exhausted for a longer period of time, memorized contents will be cleared. Should this happen, you should memorize them again.

1. Remove the cover.

+

2. Load four alkaline batteries ("AAA" size, 1.5V) matching the polarity.

+

+

•Remove the batteries when they are not used for a long time.

•Do not use the rechargeable batteries (Ni-Cd type).

•Be sure to use alkaline batteries.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Page Safety Instructions Introduction Read this Before Operating Your UnitContents Connecting Antennas System ConnectionsConnecting Video Components Hdmi High Definition Multimedia Interface connection *1Video conversion Component video input default settings *2Flow of the video signals Flow of the audio signals Audio conversionConnecting Audio Components Connecting External INSDigital input default settings Connecting Digital INS and OUTConnecting PRE Outs Front Bi-Amp Connections Connecting SpeakersSurround back speakers Speaker placement Front left and right speakers and center speakerSurround left and right speakers Surround back left and right speakersConnecting Room 2 Outs Connecting XM only for North AmericaConnecting RF Remote Antenna Connecting MULTI-ROOM System KITConnecting DC Trigger OUT Connecting PC for UpgradesSwitched AC Outlets AC InputFront Panel Controls Fluorescent DisplaySetup MIC Jack AUX in JackUniversal Remote Controls About the transmission signalFunction Table of the Numbered Buttons Remote Control Operation Range Using Functions of Remote Control Entering a setup codeSearching a setup code English Erasing the programmed command from one button Erasing all the commands programmed under a device modeTo change a macro program Programming a macro functionTo erase a macro program Operating a macro function Programming a punch-through functionOperating a punch-through function Erasing the programmed punch-through functionThen VOL is displayed on the LCD screen for several seconds Changing the transmission signal When RF is set toLoading Battery Room 2 Remote ControlsRemote Control Operation Range When selecting the External in as desired OperationsListening to a Program Source Before operationWhen CD, AUX, Video 1~ 4 is selected as an input source Muting the soundListening with headphones Achieving higher purity of sound qualitySurround modes Neural Surround Dolby Virtual SpeakerDolby Headphone Enjoying Surround Sound Dolby Digital +Listening in Dolby Headphone mode Adjusting each channel level with test toneTo cancel the surround mode for stereo operation 2CH downmix modeAdjusting the current channel level Channel levelMemorizing the adjusted channel levels Recalling the memorized channel levelsAuto tuning Manual tuningAuto presetting Listening to Radio BroadcastsManual presetting Tuning to preset stationsXM Satellite Radio only for North America Signing up for XM Satellite RadioCategory search Channel searchDirect search Presetting channels Preset search Signal strength display modeError message and status Displaying XM informationVideo RecordingDubbing from video components onto Digital Audio Recording with MD Recorder Operating the sleep timer Adjusting the brightness of the fluorescent displayOther Functions Displaying the audio informationRoom 2 Source Playback When using the buttons on the remote control unitWhen selecting the tuner as a Room 2 source When using the buttons on the front panel When selecting the Room 2 modeWhen selecting the Room 2 input When selecting the Room 2 volumeOSD Menu Settings MultiConfirm your selection When selecting the AMP Assign Setting the System SetupWhen selecting the items other than OSD Position Adjust When selecting the Tone Control When selecting the Subwoofer ModeWhen selecting the Hdmi Audio OUT When selecting the Cinema EQ When selecting the Momentary OSDWhen selecting the OSD Position Adjust When selecting the menu of page 2 or Setting the Input SetupWhen selecting the items other than Name When selecting the Hdmi Assign When selecting the Video AssignWhen selecting the Video Mode When selecting the Audio AssignWhen selecting the Audio Mode When selecting the Video ScalingWhen selecting the Auto Surround When selecting the AV SyncWhen selecting the DC Trigger When selecting the HD AudioWhen selecting the Name To resume its factory input source namePreparations Setting the Speaker / Room EQ SetupWhen selecting the Auto Setup When the auto setup has been completed When selecting the Speaker Configuration When selecting the Speaker Distance About the speaker distanceWhen selecting the Speaker Crossover When selecting the Room EQ Setup Setting the CH Level Setup Memorizing the adjusted channel levels Setting the Sound Parameter When selecting the Night ModeWhen selecting the Dolby Plii Music When selecting the Panorama modeWhen selecting the Center Width control When selecting the Dimension controlWhen selecting the Dolby Headphone When selecting the Dolby Virtual Speaker When selecting the Dolby Virtual Speaker Wide modeSetting the Multi Room Setup When selecting the Room When selecting the InputWhen selecting the Volume When adjusting the tone Bass and TrebleTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier SectionSetup Code Table AOCVCR VCR TV/VCR DVD SAT AUX-MD DKK

R-872 specifications

The Sherwood R-872 is a high-performance stereo receiver that offers an impressive combination of features, sound quality, and versatility, making it a valuable addition to any home audio system. Designed with an emphasis on audio fidelity and user convenience, the R-872 stands out as a reliable choice for both audiophiles and casual listeners alike.

One of the main features of the Sherwood R-872 is its robust power output, capable of delivering 100 watts per channel into 8 ohms. This level of power ensures that it can drive a wide range of speakers, from bookshelf models to larger floor-standing units, providing a rich and immersive listening experience. The receiver's built-in amplifier also supports low total harmonic distortion (THD) levels, which guarantees clear and accurate sound reproduction, even at high volumes.

The R-872 is equipped with a variety of connectivity options, making it easy to integrate into modern home entertainment setups. It includes multiple analog inputs for connecting various audio sources, such as CD players, turntables, and streaming devices. Additionally, it features built-in Bluetooth, allowing users to wirelessly stream music from smartphones, tablets, and computers, enhancing its versatility as a central component of any audio system.

Another noteworthy characteristic of the Sherwood R-872 is its sophisticated digital signal processing (DSP) capabilities. With multiple sound presets and adjustable equalization settings, users can tailor the audio output to their preferences, whether they are enjoying music, movies, or gaming. The receiver also offers a convenient headphone output, catering to those who prefer a private listening experience.

In terms of design, the R-872 boasts a sleek and modern aesthetic with an intuitive interface. The front panel features a clear display that provides essential information about the current audio source, volume level, and other settings. The included remote control allows for easy operation from a distance, adding to the overall user-friendly experience.

In summary, the Sherwood R-872 is a versatile and powerful stereo receiver that excels in delivering high-quality audio while accommodating a range of input sources and personal preferences. With its solid performance, modern features, and elegant design, the R-872 is an excellent choice for anyone looking to enhance their home audio setup. Whether you're listening to your favorite albums or enjoying a thrilling movie soundtrack, the R-872 ensures an engaging and enjoyable audio experience.
Top Page Image Contents