Sherwood R-872 manual Using Functions of Remote Control, Entering a setup code

Page 21

USING FUNCTIONS OF REMOTE CONTROL

•This remote control can control up to 8 different components.

•Before operating audio and video components other than this receiver with using this remote control, the setup code for each component should be entered.

•For system remote control operation, "000" was stored previously in the memory of the device button "CD" for Sherwood CD player, "DVD" for Sherwood DVD player, "AUX" for Sherwood tape deck and "TV" for Sherwood TV respectively as its factory setup code. So, you don’t need to enter its code for each Sherwood component except in such a case that its code does not work.

■Note :

•If the transmission signal which this remote control emits is changed into "RF"(Radio Frequency), this remote control cannot control other audio and video components. (For details, refer to "Changing the transmission signal" on page 29.)

Entering a setup code

4. While "LEARN" is displayed, press the CURSOR

• Setup code entry is the easiest way to program

UP(▲)/DOWN(▼) buttons to select the setup

code mode ("CODE"), then press the ENTER

this remote control for operating audio and video

button.

components.

 

1. Turn on the component you want to operate.

 

2. Find the setup codes according to the type and

 

the brand name of your component, referring to

 

"Setup Code Table" on page 77.

 

 

• Each time the CURSOR UP(▲)/DOWN(▼)

 

buttons are pressed, the mode changes as

3. Press and hold down both the ENTER button

follows :

LEARN RF-IR DELETE MACRO

and the desired one of the DEVICE buttons for

CODE PUNCH

more than 2 seconds.

• Then "PRESET" and 3 digit number are

 

displayed.

 

• If "PRESET", etc. go off, start again from the

 

above step 3.

 

5. While "PRESET", etc. are displayed, enter a 3

 

digit code and press the ENTER button.

 

Example: When entering "001".

• Then "LEARN" is displayed on the LCD screen for

 

several seconds.

• Then "OK" is displayed on the LCD screen.

 

• To be sure that the setup code is correct, press

■Notes :

the POWER ON (or STANDBY) button, aiming

• The AUDIO button is unavailable for the audio

the remote sensor on the component.

components other than this receiver.

• If the setup code is correct, your component will

• During setting operation, to exit from the setting

be turned off.

• When your component is not turned off, repeat

mode, press any of the DEVICE buttons.

the above steps 2 to 5, trying entering each code

 

 

for your component until you find one that works.

 

• If "NG" is displayed, retry entering the correct

 

setup code while "PRESET" and 3 digit number

 

are displayed.

ENGLISH

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Page Safety Instructions Read this Before Operating Your Unit IntroductionContents System Connections Connecting AntennasHdmi High Definition Multimedia Interface connection *1 Connecting Video ComponentsComponent video input default settings *2 Flow of the video signalsVideo conversion Audio conversion Flow of the audio signalsConnecting External INS Connecting Audio ComponentsConnecting Digital INS and OUT Connecting PRE OutsDigital input default settings Connecting Speakers Surround back speakersFront Bi-Amp Connections Front left and right speakers and center speaker Speaker placementSurround left and right speakers Surround back left and right speakersConnecting XM only for North America Connecting Room 2 OutsConnecting MULTI-ROOM System KIT Connecting RF Remote AntennaConnecting PC for Upgrades Connecting DC Trigger OUTSwitched AC Outlets AC InputFluorescent Display Front Panel ControlsAUX in Jack Setup MIC JackAbout the transmission signal Universal Remote ControlsFunction Table of the Numbered Buttons Remote Control Operation Range Entering a setup code Using Functions of Remote ControlSearching a setup code English Erasing all the commands programmed under a device mode Erasing the programmed command from one buttonProgramming a macro function To erase a macro programTo change a macro program Programming a punch-through function Operating a macro functionErasing the programmed punch-through function Operating a punch-through functionThen VOL is displayed on the LCD screen for several seconds When RF is set to Changing the transmission signalRoom 2 Remote Controls Remote Control Operation RangeLoading Battery Operations When selecting the External in as desiredListening to a Program Source Before operationMuting the sound When CD, AUX, Video 1~ 4 is selected as an input sourceAchieving higher purity of sound quality Listening with headphonesSurround modes Dolby Virtual Speaker Dolby HeadphoneNeural Surround Dolby Digital + Enjoying Surround SoundAdjusting each channel level with test tone Listening in Dolby Headphone modeTo cancel the surround mode for stereo operation 2CH downmix modeChannel level Adjusting the current channel levelRecalling the memorized channel levels Memorizing the adjusted channel levelsManual tuning Auto tuningAuto presetting Listening to Radio BroadcastsTuning to preset stations Manual presettingSigning up for XM Satellite Radio XM Satellite Radio only for North AmericaChannel search Direct searchCategory search Signal strength display mode Presetting channels Preset searchError message and status Displaying XM informationRecording Dubbing from video components ontoVideo Digital Audio Recording with MD Recorder Adjusting the brightness of the fluorescent display Operating the sleep timerOther Functions Displaying the audio informationWhen using the buttons on the remote control unit When selecting the tuner as a Room 2 sourceRoom 2 Source Playback When selecting the Room 2 mode When using the buttons on the front panelWhen selecting the Room 2 input When selecting the Room 2 volumeMulti OSD Menu SettingsConfirm your selection Setting the System Setup When selecting the items other than OSD Position AdjustWhen selecting the AMP Assign When selecting the Subwoofer Mode When selecting the Hdmi Audio OUTWhen selecting the Tone Control When selecting the Momentary OSD When selecting the Cinema EQWhen selecting the OSD Position Adjust Setting the Input Setup When selecting the items other than NameWhen selecting the menu of page 2 or When selecting the Video Assign When selecting the Hdmi AssignWhen selecting the Video Mode When selecting the Audio AssignWhen selecting the Video Scaling When selecting the Audio ModeWhen selecting the AV Sync When selecting the Auto SurroundWhen selecting the DC Trigger When selecting the HD AudioTo resume its factory input source name When selecting the NameSetting the Speaker / Room EQ Setup When selecting the Auto SetupPreparations When the auto setup has been completed When selecting the Speaker Configuration About the speaker distance When selecting the Speaker DistanceWhen selecting the Speaker Crossover When selecting the Room EQ Setup Setting the CH Level Setup Memorizing the adjusted channel levels When selecting the Night Mode Setting the Sound ParameterWhen selecting the Panorama mode When selecting the Dolby Plii MusicWhen selecting the Center Width control When selecting the Dimension controlWhen selecting the Dolby Headphone When selecting the Dolby Virtual Speaker Wide mode When selecting the Dolby Virtual SpeakerSetting the Multi Room Setup When selecting the Input When selecting the RoomWhen selecting the Volume When adjusting the tone Bass and TrebleProblem Possible Cause Remedy Troubleshooting GuideAmplifier Section SpecificationsAOC Setup Code TableVCR VCR TV/VCR DVD SAT AUX-MD DKK

R-872 specifications

The Sherwood R-872 is a high-performance stereo receiver that offers an impressive combination of features, sound quality, and versatility, making it a valuable addition to any home audio system. Designed with an emphasis on audio fidelity and user convenience, the R-872 stands out as a reliable choice for both audiophiles and casual listeners alike.

One of the main features of the Sherwood R-872 is its robust power output, capable of delivering 100 watts per channel into 8 ohms. This level of power ensures that it can drive a wide range of speakers, from bookshelf models to larger floor-standing units, providing a rich and immersive listening experience. The receiver's built-in amplifier also supports low total harmonic distortion (THD) levels, which guarantees clear and accurate sound reproduction, even at high volumes.

The R-872 is equipped with a variety of connectivity options, making it easy to integrate into modern home entertainment setups. It includes multiple analog inputs for connecting various audio sources, such as CD players, turntables, and streaming devices. Additionally, it features built-in Bluetooth, allowing users to wirelessly stream music from smartphones, tablets, and computers, enhancing its versatility as a central component of any audio system.

Another noteworthy characteristic of the Sherwood R-872 is its sophisticated digital signal processing (DSP) capabilities. With multiple sound presets and adjustable equalization settings, users can tailor the audio output to their preferences, whether they are enjoying music, movies, or gaming. The receiver also offers a convenient headphone output, catering to those who prefer a private listening experience.

In terms of design, the R-872 boasts a sleek and modern aesthetic with an intuitive interface. The front panel features a clear display that provides essential information about the current audio source, volume level, and other settings. The included remote control allows for easy operation from a distance, adding to the overall user-friendly experience.

In summary, the Sherwood R-872 is a versatile and powerful stereo receiver that excels in delivering high-quality audio while accommodating a range of input sources and personal preferences. With its solid performance, modern features, and elegant design, the R-872 is an excellent choice for anyone looking to enhance their home audio setup. Whether you're listening to your favorite albums or enjoying a thrilling movie soundtrack, the R-872 ensures an engaging and enjoyable audio experience.
Top Page Image Contents