Sherwood R-872 manual OSD Menu Settings, Multi

Page 50

ENGLISH

OSD Menu Settings

•The OSD (On-Screen Display) menu is a setting menu that is displayed on the monitor TV and allows you to perform the setup procedures easily. In most situations, you will only need to set this once during the installation and layout of your home theater, and it rarely needs to be changed later.

The OSD menu consists of 6 main menus ; system setup, input setup, speaker / room EQ setup, CH level setup, sound parameter and multi room setup. These menus are then divided up into various sub-menus.

■Note:

•When the component video signals or the HDMI video signals are input and these signals are output from the MONITOR OUTs, the momentary OSD cannot be displayed.

■Navigating through the OSD menu

•The explanations here assume you are using the buttons on the remote control when performing the OSD menu operation. However, you can use the buttons on the front panel as well.

The buttons on the front panel correspond to those on the remote control as shown below.

1. Turn the menu screen on.

MULTI

•The main menu will be shown.

•To turn the menu screen off, press this button again.

2. Select the desired menu using the CURSOR UP(▲)/DOWN(▼) buttons.

50

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Page Safety Instructions Introduction Read this Before Operating Your UnitContents Connecting Antennas System ConnectionsConnecting Video Components Hdmi High Definition Multimedia Interface connection *1Video conversion Component video input default settings *2Flow of the video signals Flow of the audio signals Audio conversionConnecting Audio Components Connecting External INSDigital input default settings Connecting Digital INS and OUTConnecting PRE Outs Front Bi-Amp Connections Connecting SpeakersSurround back speakers Surround left and right speakers Speaker placementFront left and right speakers and center speaker Surround back left and right speakersConnecting Room 2 Outs Connecting XM only for North AmericaConnecting RF Remote Antenna Connecting MULTI-ROOM System KITSwitched AC Outlets Connecting DC Trigger OUTConnecting PC for Upgrades AC InputFront Panel Controls Fluorescent DisplaySetup MIC Jack AUX in JackUniversal Remote Controls About the transmission signalFunction Table of the Numbered Buttons Remote Control Operation Range Using Functions of Remote Control Entering a setup codeSearching a setup code English Erasing the programmed command from one button Erasing all the commands programmed under a device modeTo change a macro program Programming a macro functionTo erase a macro program Operating a macro function Programming a punch-through functionOperating a punch-through function Erasing the programmed punch-through functionThen VOL is displayed on the LCD screen for several seconds Changing the transmission signal When RF is set toLoading Battery Room 2 Remote ControlsRemote Control Operation Range Listening to a Program Source When selecting the External in as desiredOperations Before operationWhen CD, AUX, Video 1~ 4 is selected as an input source Muting the soundListening with headphones Achieving higher purity of sound qualitySurround modes Neural Surround Dolby Virtual SpeakerDolby Headphone Enjoying Surround Sound Dolby Digital +To cancel the surround mode for stereo operation Listening in Dolby Headphone modeAdjusting each channel level with test tone 2CH downmix modeAdjusting the current channel level Channel levelMemorizing the adjusted channel levels Recalling the memorized channel levelsAuto presetting Auto tuningManual tuning Listening to Radio BroadcastsManual presetting Tuning to preset stationsXM Satellite Radio only for North America Signing up for XM Satellite RadioCategory search Channel searchDirect search Error message and status Presetting channels Preset searchSignal strength display mode Displaying XM informationVideo RecordingDubbing from video components onto Digital Audio Recording with MD Recorder Other Functions Operating the sleep timerAdjusting the brightness of the fluorescent display Displaying the audio informationRoom 2 Source Playback When using the buttons on the remote control unitWhen selecting the tuner as a Room 2 source When selecting the Room 2 input When using the buttons on the front panelWhen selecting the Room 2 mode When selecting the Room 2 volumeOSD Menu Settings MultiConfirm your selection When selecting the AMP Assign Setting the System SetupWhen selecting the items other than OSD Position Adjust When selecting the Tone Control When selecting the Subwoofer ModeWhen selecting the Hdmi Audio OUT When selecting the Cinema EQ When selecting the Momentary OSDWhen selecting the OSD Position Adjust When selecting the menu of page 2 or Setting the Input SetupWhen selecting the items other than Name When selecting the Video Mode When selecting the Hdmi AssignWhen selecting the Video Assign When selecting the Audio AssignWhen selecting the Audio Mode When selecting the Video ScalingWhen selecting the DC Trigger When selecting the Auto SurroundWhen selecting the AV Sync When selecting the HD AudioWhen selecting the Name To resume its factory input source namePreparations Setting the Speaker / Room EQ SetupWhen selecting the Auto Setup When the auto setup has been completed When selecting the Speaker Configuration When selecting the Speaker Distance About the speaker distanceWhen selecting the Speaker Crossover When selecting the Room EQ Setup Setting the CH Level Setup Memorizing the adjusted channel levels Setting the Sound Parameter When selecting the Night ModeWhen selecting the Center Width control When selecting the Dolby Plii MusicWhen selecting the Panorama mode When selecting the Dimension controlWhen selecting the Dolby Headphone When selecting the Dolby Virtual Speaker When selecting the Dolby Virtual Speaker Wide modeSetting the Multi Room Setup When selecting the Volume When selecting the RoomWhen selecting the Input When adjusting the tone Bass and TrebleTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier SectionSetup Code Table AOCVCR VCR TV/VCR DVD SAT AUX-MD DKK

R-872 specifications

The Sherwood R-872 is a high-performance stereo receiver that offers an impressive combination of features, sound quality, and versatility, making it a valuable addition to any home audio system. Designed with an emphasis on audio fidelity and user convenience, the R-872 stands out as a reliable choice for both audiophiles and casual listeners alike.

One of the main features of the Sherwood R-872 is its robust power output, capable of delivering 100 watts per channel into 8 ohms. This level of power ensures that it can drive a wide range of speakers, from bookshelf models to larger floor-standing units, providing a rich and immersive listening experience. The receiver's built-in amplifier also supports low total harmonic distortion (THD) levels, which guarantees clear and accurate sound reproduction, even at high volumes.

The R-872 is equipped with a variety of connectivity options, making it easy to integrate into modern home entertainment setups. It includes multiple analog inputs for connecting various audio sources, such as CD players, turntables, and streaming devices. Additionally, it features built-in Bluetooth, allowing users to wirelessly stream music from smartphones, tablets, and computers, enhancing its versatility as a central component of any audio system.

Another noteworthy characteristic of the Sherwood R-872 is its sophisticated digital signal processing (DSP) capabilities. With multiple sound presets and adjustable equalization settings, users can tailor the audio output to their preferences, whether they are enjoying music, movies, or gaming. The receiver also offers a convenient headphone output, catering to those who prefer a private listening experience.

In terms of design, the R-872 boasts a sleek and modern aesthetic with an intuitive interface. The front panel features a clear display that provides essential information about the current audio source, volume level, and other settings. The included remote control allows for easy operation from a distance, adding to the overall user-friendly experience.

In summary, the Sherwood R-872 is a versatile and powerful stereo receiver that excels in delivering high-quality audio while accommodating a range of input sources and personal preferences. With its solid performance, modern features, and elegant design, the R-872 is an excellent choice for anyone looking to enhance their home audio setup. Whether you're listening to your favorite albums or enjoying a thrilling movie soundtrack, the R-872 ensures an engaging and enjoyable audio experience.
Top Page Image Contents