15 TROUBLESHOOTING

MELSEC-Q

 

Related buffer memory

Set range

 

 

 

 

address

 

 

 

Remedy

 

 

 

 

 

 

(Setting with sequence program)

 

Axis 1

Axis 2

Axis 3

Axis 4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

20

170

320

470

• [mm] [inch] [pulse]

• Bring the setting into the setting range.

 

21

171

321

471

–2147483648 to 2147483647

• In a unit other than degree, set so that the lower limit

 

 

 

• [degree] 0 to 35999999

value is smaller than the upper limit value.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

22

172

322

472

0, 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

23

173

323

473

0, 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

24

174

324

474

1 to 2147483647

 

 

25

175

325

475

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

26

176

326

476

1 to 500

 

 

 

 

 

 

 

 

 

 

 

 

 

With the setting brought into the setting range, turn the

 

27

177

327

477

0, 1

 

PLC READY signal [Y0] from OFF to ON.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

28

178

328

478

0, 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

29

179

329

479

0, 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30

180

330

480

0, 1, 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

33

 

 

 

 

 

 

 

 

 

0, 1, 2, 3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Speed-position switching control (ABS mode) should

 

 

 

 

 

 

 

 

 

 

 

 

satisfy the conditions 1) to 3) given on the left. When

 

34

184

334

484

0, 2

speed-position switching control (ABS mode) is not to

 

 

 

 

 

 

 

 

 

 

 

 

be exercised, set 0 to speed-position function selection

 

 

 

 

 

 

 

 

 

 

 

 

and turn the PLC READY signal (Y0) from OFF to ON.

 

 

 

 

 

 

 

 

36

186

336

486

1 to 8388608

 

 

37

187

337

487

 

 

 

 

 

 

 

 

 

 

 

 

38

188

338

488

1 to 8388608

 

 

39

189

339

489

 

 

 

With the setting brought into the setting range, turn the

 

 

 

 

 

 

 

 

 

 

 

 

 

40

190

340

490

 

PLC READY signal [Y0] from OFF to ON.

 

1 to 8388608

 

 

41

191

341

491

 

 

 

 

 

 

 

 

 

 

 

 

42

192

342

492

1 to 8388608

 

 

43

193

343

493

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

15 - 27

Page 631
Image 631
Mitsubishi Electronics QD75D, QD75P user manual Mm inch pulse Bring the setting into the setting range