15 TROUBLESHOOTING

MELSEC-Q

Classification

Error

Error name

 

Error

Operation status at error occurrence

 

of errors

code

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

At start: The system will not operate.

 

 

 

 

 

 

During operation:

 

 

 

 

The setting value of ABS direction in

The system decelerates to a

 

 

 

Illegal setting of ABS

the unit of degree is as follows.

stop.

 

Positioning

 

(Note that, in the continuous

 

546

direction in unit of

• Set outside the setting range.

 

operation

 

 

degree

• A figure other than "0" is set when

positioning control and continuous

 

 

 

 

 

 

 

path control, the system continues

 

 

 

 

the software stroke limit is valid.

operating with the setting set at the

 

 

 

 

 

 

 

 

 

 

 

 

time of start even if the setting is

 

 

 

 

 

 

changed during the operation.)

 

 

 

 

 

 

 

 

 

 

 

 

 

At start: The system will not operate.

 

 

 

 

 

 

During operation:

 

 

 

 

 

 

The system stops with the

 

 

 

 

In the PLC CPU unit parameter

setting (deceleration

 

 

 

 

stop/sudden stop) of the

 

 

800

Hold error

"Output at error stop", the setting for

detailed parameter 2 sudden

 

 

 

 

QD75 is "Hold".

 

stop selection

 

 

 

 

 

 

(stop group 3).

 

 

 

 

 

 

(Note that the deceleration stop only

 

 

 

 

 

 

occurs during the manual pulse

 

 

 

 

 

 

generator operation.)

 

 

801

Flash ROM write

Data is not written to the flash ROM.

 

 

 

 

error

 

 

 

 

 

 

 

 

 

At start: The system will not operate.

 

 

802

Flash ROM sum

While data is written to the flash

 

 

 

 

 

check error

ROM, the power is turned OFF.

 

 

 

 

 

 

 

 

 

803

PLC CPU error

The PLC CPU resulted in an error.

 

 

 

 

 

• The ABRST

instruction is

 

 

 

 

 

executed with the status set to

At start: The system will not operate.

 

 

 

 

other than 0.

 

 

 

 

 

 

 

 

I/F

 

 

• The PSTRT

instruction is

During operation:

 

 

 

 

executed with the start No. set to

The system stops with the

 

 

 

 

other than 10 to 600, 7000 to 7004

setting (deceleration

 

 

 

 

and 9001 to 9004.

stop/sudden stop) of the

 

 

804

Dedicated instruction

• The TEACH

instruction is

detailed parameter 2 sudden

 

 

error

executed with the teaching data

stop selection

 

 

 

 

selection set to other than 0 and 1.

(stop group 3).

 

 

 

 

• The TEACH

instruction is

(Note that the deceleration stop only

 

 

 

 

executed with the positioning data

occurs during the manual pulse

 

 

 

 

No. set to other than 1 to 600.

generator operation.)

 

 

 

 

• The instruction of a non-existent

 

 

 

 

 

axis is specified by the ABRST ,

 

 

 

 

 

PSTRT or TEACH instruction.

 

 

 

 

 

 

 

 

 

 

Flash ROM write

Data is written to the flash ROM

 

 

 

805

continuously 25 times or more from

 

 

 

number error

At start: The system will not operate.

 

 

 

 

the sequence program.

 

 

 

 

 

 

 

 

806

Dedicated instruction

Mismatching occurs between the

 

 

 

 

I/F error

PLC CPU and QD75.

 

 

15 - 22

Page 626
Image 626
Mitsubishi Electronics QD75P At start The system will not operate During operation, Unit of degree is as follows Stop