GE JSP40, JSP38 warranty ANTI-TIP Device, 9II

Page 34

ANTI-TIP DEVICE

1.Before placing range in the counter, notice the location of the stability bracket which is already attached to the back of the range. This location should work for most installations. However, it may be more convenient to hook the stability chain to the unit when the stability bracket is attached to the upper set of holes in the back of range. See Fig. A. The upper level set of holes are intended for use with a backsplash kit. If the backsplash is not being used, make sure that there are no structural supports for the countertop which will interfere with the stability bracket when located in the upper set of holes.

—

9II

 

 

‘s,

Chain

 

 

 

 

 

Wall Plate

Long Screw\ --..,

 

 

 

Washer <

 

 

 

 

 

)\ , ~

 

 

 

\\\\\\\

 

 

 

 

3.

Temporarily attach the loose end of the chain

 

to the rear of the countertop with the tape from

 

the packaging. See Fig. D.

4.

Place the range in the counter cutout leaving just

 

enough room between the back of the range and

o

Bracket

Optional

Location

Bracket

Location

c

2.Fasten one end of the stability chain to the floor or wall with the lomz screw and

guard

ainback

@Chain —

the wall to reach the stability bracket.

5. Hook the loose end of the chain onto the bracket

by slipping the nearest link of the chain into the

slot in the bracket. See Fig. A and make sure the

chain is pulled as tight as possible and that there

is no excess slack in the chain after the chain is

attached to the bracket.

r

CAUTION: Excessive slack in the chain A could allow the range to tip over.

6.Slide the range all the way back into the counter.

Once the range is pushed back in place, there will — be a small amount of slack in the chain. This

is normal.

‘ig’;”akecertainwasher supplied. See ‘%*

the screw is going

into the wall-plat= at the base of the wall or one of the studs in the base of the wall. See Fig. C. Whether you attach the chain to the wall or floor, be certain that the screw is in at least 3/4 inch thickness of wood other than baseboard and that there are no electrical wires or plumbing in the area which the screw could penetrate. Attach the stability chain in a location which will allow the chain to be in line with the bracket side to aid as much as possible when attached to the unit. Test to see if the chain is securely fastened by tugging on the chain.

NOTE:

●If attaching to masonry, you can buy suitable screws and anchors at hardware stores. Use a masonry drill to drill the required holes.

●If range is removed for cleaning or any other reason, make sure chain is reattached.

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents IiliiH If YOU Need Service Help US Help YOUAwarning @ORTANT Safety NoticeResult in tipping of the range and injury Important Safety Instructions OvenUse care when touching the cooktop Save These InstructionsFeatures of Your Range Explained on 15, 16 Leveling InstallingPreparation Removing Packaging MaterialsSurface Controls How totheS t ControlsDual Surface Unit Switch Cooking Guide for Using Heat Settings~.o, # Gqj ‘?,-+ ‘e,, titi’’% ’’ Ogfl \ How to Check Pan Performance Ypes of CookwareDeep Fat Frying Surface Cookware TipsWok Cooking Observe the Following Points in Canning Flat-bottomed canners are recommendedFor heavy, burned on soil Surface CleaningGlass Ceramic Cooktop Cleaning General InformationFeatures of Your Oven Control WwwOven CONTROL, Clock and Timer Oven Light Using Your Oven~fore Using Your Oven Shelf PositionsPreheating How to Set Your Range for BakingBaking \ Type of Food \ Shelf PositionBaking Guides Pan PlacementJaking Pans CookiesTimed Baking How to Time BakeHow to Set Immediate Start and Automatic Stop Aluminum FoilOW to Set Delay Start and Automatic Stop Quick ReminderAdjust the Oven Thermostat To Adjust the ThermostatRoasting Use of Aluminum FoilQuestions and Answers Frozen Roasts‘se of Aluminum Foil Why are my meats not turning out as brown as they should?Should I salt the meat before broiling? Broiling Guide Operating the SELF-CLEANING Oven Before a Clean CycleHow to Set Oven for Cleaning To Stop a Clean CycleIter Self-Cleaning How to Set Delay Start of CleaningWhy do I have ash left in my oven after cleaning? Should there be any odor during the cleaning?My oven shelves do not slide easily. What is the matter? Control Panel and Knobs Oven Shelves Clean the shelves with an abrasive cleanser orSure Grip Handle Inside of the door Broiler Pan and RackLift-Off Oven Door Outside of the doorOven Vent Duct ~.emovable Storage DrawerOven Light Bulb Glass WindowANTI-TIP Device 9IIUSE this Problem Solver TElProblem Solver Problem Possible CausePage Page We’ll Be There Warranty
Related manuals
Manual 36 pages 9.21 Kb

JSP38, JSP40 specifications

The GE JSP40 and JSP38 are advanced gas turbine models developed by General Electric, renowned for their efficiency, reliability, and cutting-edge technology in power generation. These turbines are designed to meet the demanding requirements of modern energy markets, providing flexible solutions for various applications, including peaking power and baseload generation.

One of the main features of the JSP40 and JSP38 is their advanced aerodynamics, which contribute to high thermal efficiency and reduced emissions. The innovative design of the turbine blades enhances airflow and maximizes energy extraction from the combustion process, leading to improved overall performance. With a base load efficiency exceeding 40 percent, these turbines are positioned as leaders in their class, offering significant fuel savings for operators.

The JSP40 and JSP38 utilize advanced materials and coatings that enhance durability and resistance to high temperatures. This enables them to operate at higher pressure ratios and temperatures compared to earlier models, thereby increasing power output. The use of advanced nickel-based superalloys in the manufacturing of turbine components ensures long service life even under harsh operational conditions.

Additionally, these turbines are equipped with GE’s proprietary DLN (Dry Low NOx) combustion technology. This technology minimizes nitrogen oxide emissions, making the JSP40 and JSP38 compliant with stringent environmental regulations. The DLN systems achieve stable combustion across a wide range of loads, providing operators with the flexibility to efficiently manage varying demand levels while maintaining low emissions.

Both models feature integrated digital controls that provide real-time monitoring and analytics, improving operational efficiency and reducing downtime. GE's sophisticated control systems enable predictive maintenance, ensuring that potential issues are identified before they escalate, thus optimizing maintenance schedules and maximizing turbine availability.

Furthermore, the JSP40 and JSP38 are designed with adaptability in mind. They can be configured to burn a variety of fuels, including natural gas and distillate fuels, allowing fleets to respond to market changes and regulatory requirements seamlessly. This versatility empowers operators to take advantage of different fuel prices while maintaining a reliable power supply.

In summary, the GE JSP40 and JSP38 gas turbines represent a significant advancement in energy technology, combining high efficiency, reliability, and environmental performance. Their innovative features and advanced technologies make them an excellent choice for energy producers looking to meet the challenges of today’s dynamic energy landscape. With continued investment in research and development, GE is poised to maintain its position as a leader in the global power generation market.
Top Page Image Contents