GE JGBS19GEP, JGSS05GES, JGSS05GER, JGBS15GER Leveling the Range, Installing IHEAHII.IIP Device

Page 39

❑LEVELING THE RANGE

1.Remove the storage drawer, broiler drawer or kick panel.

2.Use a 3/16” open-end or socket wrench to back out both rear leveling legs approximately two turns.

3.Use a 1’%” open-end or adjustable wrench to back out the front leveling legs two turns.

4.Install the oven shelves in

the oven and position the range where it will be installed.

5.Check for levelness by placing a spirit level or a cup, partially filled with water, on one of the oven racks. If using a spirit level, take two readings—with the level placed diagonally first in one direction and then the other.

6.Adjust the leveling legs until the range is level.

7.After the range is level, slide the range away from the wall so that the Anti-Tip device can be installed.

❑11 INSTALLING IHEAHII.IIP DEVICE

WARNING:

●Range must be secured with an approved Anti-Tip device.

s Unless properly installed, the range could be tipped by you or a child standing, sitting or leaning on an open door.

. After installing the Anti-Tip device, verify that it is in place by carefully attempting to tilt the range forward.

●This range has been designed to meet all recognized industry tip standards for all normal conditions.

. The use of this device does not preclude tipping of the range when not properly installed.

. If the Anti-Tip device supplied with the range does not fit this application, use the universal Anti-Tip device WB02X7909.

1.Mark the wall where the NGHT EDGE of the range is to be located. Be sure to allow for the countertop overhang if you intend to install the range next to cabinets.

toward the center of the range from the marked edge of the range.

3.Using the device as a template, mark the position of the hole for the screw.

4.For wood construction, drill a pilot hole at an angle of 20 degrees from the horizontal. A nail or awl maybe used if a drill is not available.

Mount the Anti-Tip device with the screw provided.

For cement or concrete construction, you will need a 1/4” x 1%” lag bolt and a 1/2” O.D. sleeve anchor, which are not provided. Drill the recommended size hole for the hardware.

Install the sleeve anchor into the drilled hole and then install the lag bolt through the device. The bolts must be properly tightened as recommended for the hardware.

5.Slide the range against the wall, and check for proper instillation by grasping the front edges of the rear surface unit openings and carefully attempting to tilt the range forward.

WHEN ALL HOOKUPS ARE COMPLETED:

~KE SURE ALL CONTROLS ARE LEFT IN THE OFF POSITION.

~KE SURE THE FLOW OF COMBUSTION AND VENTILATION AIR TO THE MNGE IS UNOBSTRUCTED.

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Xl#TM Gas Range ~LP US ~LP YOU YOU NED ServiceLoeat~ the range out of kitchen tra~ic path Fluorescent Eght btibs and safety valves onMen You Get Your Range Usbg Your RangeExcessive flame is hazardous Wortant Safety ~STRUCTIONSSutiace Cooking Make sure the burners have ignitedCleating Your Range When a pilot goes out on a model with standingSave T~SE ~STRUCTIONS5 Baking, Brofiing and RoastingFEATu~s of Your Range Page Surface Burner Controls SU~ACE COO~GElectric Ignition Models Standing Pilot ModelsAfter Lighting a Burner Before Lighting a BurnerStanding Pilot Model Use of Stove Top Grills How to Select Flame SizeTop-of-Range Cookware Wok CookingClock Am TMR To Set the TimerTo Change or Cancel the Timer Setting To Display the Time of Day While the Timer Is OperatingUSmG Your OWN TimerBefore Using Your Oven Power OutageTo replace, place Shelf on Shelf support with Oven VentsOven Shelves To light the oven pilotOven Moisture Do It Yourse~-Adjust the Oven ThermostatUS~G Your Oven Shelf PositionsOven Shelves How To Set Your Range For BakingPan Placement PreheatingBA~G ROASTmG Frozen RoasbDual Shelf Cooking ROAST~G GU~E Questions and AnswersQuestions & Answers How to BroilBROmmGw Use of Aluminum FoilBROmmG G~E Sealed Burner Assemblies on some models ~Gra’eCAm Am CLEA~G Burner Heads on sealed burners only~dishwasherm ‘illedscoufingpadi fnecessq Oven bottom has a porcelain enamel finish Cooktop SurfaceOven Bottom Burner GratesControl Panel and Knobs CA~ Am CLEA~GOven Light Bulb on some models Broiler Pan and RackOven Door Oven Air VentsNever block the vents air openings of the range Painted Surfaces CAm Am CLEAN~GGlass Surfaces Metal PartsRemovable Kick Panel on some models Air Adjustment Shutters for Oven BurnersRemovable Broiler Drawer on some models Removable Storage Drawer on some modelsFor Your Safety Imwrtant Safety Instructions General Confect the Range to GAS Provide Adequate GAS SupplyConnect the Whge to GM Circuit IMPORTN-Please read carefillyShould have Wall receptacleELECTRl~L Connections Light the Oven Pilot Seal the OpeningsNormal for LP gas Sofi blue tie~ Normal for natural gas Outer conesCheck Ignition of Surface Burners YeMow tips onPage To remove tie burner btifle on some models Leveling the Range Installing IHEAHII.IIP DevicePrepare Range for Conversion ~~G Do not remove the pressure regulator from the rangeIt is this regulator Tools RequiredBurnercap~ Straight outOpposite the burner electrode in each burner base For Models Equipped with Standing PilotsThermostat shaft. Turn Screwfull open position. With To convert to U gasTo convert to natird gas Loosen the spud about 2 turnsConvert TOP Burner Valves HOW to Convert the Range for USEOven controls not properly set Yellow flamesAluminum foil being used improperly in oven Oven bottom not securely seated in positionQUESTIONS? USE this Problem Solver We’ll Be There Warranty

JGBS02EM, JGBS02PN, JGBS16GEP, JGBS04GPR, JGBS04PR specifications

General Electric (GE) has long been a leader in the home appliance sector, known for producing reliable and innovative products. The models JGSS05GES, JGSS05GER, JGBS15GER, JGBS12GER, and JGBS06ES exemplify their commitment to quality, efficiency, and advanced technology in the realm of gas cooking appliances.

The JGSS05GES and JGSS05GER are part of GE’s freestanding gas ranges, offering a combination of style and functionality. These models feature a modern stainless steel finish, providing a sleek and robust aesthetic that complements various kitchen designs. Equipped with powerful gas burners, they deliver precise heat control for various cooking methods, from simmering sauces to boiling water. Both models come with a large oven capacity, perfect for accommodating family meals or holiday gatherings. One of the standout features is the self-cleaning option, making maintenance easier for busy households.

The JGBS15GER and JGBS12GER models take versatility a step further with their continuous grates that allow for seamless movement of pots and pans across burners. This thoughtful design enhances stability and ease of use for cooks who frequently switch pans during meal preparation. Moreover, both models are designed with an electronic ignition system, ensuring reliable and quick startup without the ongoing hassle of matches or lighters.

Finally, the JGBS06ES model integrates additional energy-saving technologies that cater to environmentally conscious consumers. With its high-efficiency burners and insulation, the gas range minimizes energy consumption while maximizing performance.

All five ranges are equipped with easy-to-use controls, allowing users to fine-tune temperatures with precision. Furthermore, they incorporate GE’s commitment to safety, featuring child lock options and oven sensors that help prevent overheating.

These GE gas ranges exemplify a blend of modern features and classic reliability, making them ideal choices for any kitchen setting. Whether cooking for a crowd or preparing a simple meal, these models ensure both efficiency and quality, solidifying GE’s reputation as a trusted name in home cooking appliances.
Top Page Image Contents