Maytag 110 Gas Connection, Pressure testing, Electrical Connection, Pressures

Page 27

INSTALLATION

Check the appliance is electrically safe and gas sound when you have finished.

1.Place the cooker in its intended position and level the appliance.

2.Draw a pencil line 100mm from the front edge of the levelling feet.

3.Mark the centre line for the bracket by measuring 550mm from the L.H. side of the cooker.

4.Remove the cooker.

5.Measure back from the pencil line 535mm to locate the front edge of the bracket. Fix bracket to floor.

6.Measure height from floor level to engagement edge in back of cooker. Add 3mm to this dimension and assemble stability bracket to this height. (i.e. from floor level to underside of top member) and ensure bracket does not foul oven burner assembly.

Gas Connection

Bappliance gas inlet

Because the height of the cooker can be adjusted and each connection is different it is difficult to give precise dimensions. Ideally the house supply bayonet should be in the shaded area shown in the diagram. Although a 900mm hose can be used, a 1250mm hose will allow slightly more flexibility in the positioning of the bayonet and make moving the cooker easier. The hose should be fitted so that both inlet and outlet connections are vertical so that the hose hangs downwards.

The connector is located just below the hotplate level at the rear of the cooker.

For Natural Gas the flexible hose must be in accordance with B.S.669.

If in doubt contact, your supplier.

Screw connect the threaded end of the hose into the gas inlet in the underside of the connector block on the back of the cooker.

After completing the gas connection, check the cooker is gas sound with a pressure test.

Pressure testing

The gas pressure can be measured at one of the hotplate burner jets (NOT a Wok burner). Make sure that the cooker is not connected to the electricity supply. Lift off

a burner head. Fit the pressure gauge to the jet. Turn on one of the other burners and light it with a match. Turn on the control for the hotplate burner to which the pressure gauge is fitted. Press in the knob to allow the gas through and register the pressure on the gauge.

Pressures

Natural Gas

LP Gas cookers

20mbar.

Butane 29mbar

 

Propane 37mbar

 

 

A hose is not supplied by with the cooker. Hoses may be purchased at most builders’ merchants.

The Gas supply needs to terminate with a down facing bayonet. The rear cover boxes limit the position of the supply point.

Reassemble burner top, making sure it is reassembled in the correct way on the burner body.

Electrical Connection

This appliance must be installed by a qualified electrician to comply with the relevant Institute of Electrical Engineers (I.E.E.) regulations and also the local electricity supply company requirements.

WARNING: THIS APPLIANCE MUST BE EARTHED

Note

The cooker must be connected to the correct electrical supply as stated on the voltage label on the cooker, through a suitable cooker control unit incorporating a double pole switch having a contact separation of at least 3mm in all poles. This cooker must not be connected to an ordinary domestic power point.

view from the rear

A position for gas supply connector

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Dual Fuel Range Cooker Users Guide Installation InstructionsPeculiar smells InstallationBe safe Gas and Electricity onContents Hotplate Burners Griddle Care and Cleaning Wok cradleGrill Use only heat resistant dishes WarmerPlate Warming Holding of ‘Hot Food’Left Hand Oven The Right Hand Oven OvensClock To turn off the key lock Auto is showing, you want to reset to manual cookingClock Special Features Key Lock To activate the key lockCooking using the timer Multi-function ovenBoth Ovens Defrost Multi-function oven functionsOven shelves Oven lightSteam Multi-function Oven cooking guide Ensure meat and poultry is fully cooked before servingFood Roast Meats Oven Cooking chart Conventional and full Fan oven functionsWok burners Cleaning your cookerHotplate burners Central hotplateOven and Grill Cleaning Table HotplatePart Finish Recommended Cleaning Method Outside of cookerOvens GriddleGrill Control Panel and DoorsTroubleshooting Turn off the power supply Oven light is not workingHotplate burners will not light General Safety Instructions If you smell gas0800 111 This appliance is heavy, take care when moving it Installation Dear InstallerThank you These are not supplied by with the cooker but Provision of VentilationLocation of Cooker ConversionPositioning the Cooker Checking the partsFitting a stability bracket Unpacking the CookerMoving the Cooker LevellingPressures Pressure testingGas Connection Electrical ConnectionThank you Oven checkFitting the plinth Customer careTap Bypas screws Conversion to LP gasJets Stick on labelServicing To Remove the Hotplate Spark Generator To Adjust the Oven Door Catch KeeperTo Remove a Hotplate Burner Spark Electrode To Remove an Oven DoorTo Remove the LH Oven Bottom and Top Elements To Remove Oven Inner BackTo Replace an Oven Fan To Remove an Oven fan ElementCircuit Diagram Connections Technical DataDimensions This cooker is category II2H3+Ratings Maytag UK
Related manuals
Manual 2 pages 17.4 Kb

110 specifications

The Maytag 110 series is a line of high-efficiency washing machines known for their robust performance, reliability, and user-friendly features. Designed to meet the demands of modern households, the Maytag 110 stands out due to its powerful cleaning capabilities and advanced technology.

One of the key features of the Maytag 110 is its impressive capacity. With its spacious drum, this washer can accommodate large loads of laundry, making it ideal for families or individuals who require frequent washing. Its efficient design allows users to clean more clothes in fewer cycles, ultimately saving time and energy.

In terms of performance, the Maytag 110 employs a commercial-grade motor which provides consistent and powerful agitation. This motor reduces vibrations and noise during the wash cycle, ensuring a quiet operation. Additionally, the machine features a unique PowerWash cycle that combines extra cleaning action and heated water to tackle tough stains and ensure an impeccable clean.

The Maytag 110 also incorporates advanced washing technology. The Precision Clean wash system optimizes water usage while ensuring maximum cleaning efficiency. This system manages the water levels based on the size of the load, which helps to conserve water while ensuring that each item is thoroughly cleaned.

Moreover, the Maytag 110 is equipped with a variety of wash cycles and settings to accommodate different fabric types and soil levels. Options like Delicate, Heavy Duty, and Quick Wash allow users to customize their washing experience, ensuring the best care for every garment.

Durability is another hallmark of the Maytag brand, and the 110 series is no exception. Constructed with a solid metal frame and a stainless steel wash basket, the unit is designed to withstand the rigors of daily use. The robust build quality is further complemented by a 10-year limited parts warranty, reassuring users of the machine's longevity.

Additional thoughtful features include a lid lock system for safety, LED cycle status indicators, and a large, easy-to-use control panel that simplifies operation. The Maytag 110 also adheres to energy efficiency standards, making it an environmentally friendly choice that can help reduce utility bills.

In summary, the Maytag 110 series offers a powerful, efficient, and durable washing solution. With its combination of advanced technology, user-friendly design, and effective cleaning capabilities, it represents a reliable option for anyone seeking a high-performance washing machine.
Top Page Image Contents