Multiquip QP2TH manual Basic Engine, Initial Servicing, Muffler Used to reduce noise and emissions

Page 15

BASIC ENGINE

Figure 4. Engine Controls and Components

INITIAL SERVICING

The engine (See Figure 4) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturers engine manual for instructions and details of operation and servicing. The engine shown above is a HONDA engine, operation for other types of engines may vary somewhat.

1.Fuel Filler Cap — Remove this cap to add unleaded gasoline to the fuel tank. Make sure cap is tightened securely. DO NOT over fill.

DANGER

Adding fuel to the tank should be done only when the engine is stopped and has had an opportunity to cool down. In the event of a fuel spill, DO NOT attempt to start the engine until the fuel residue has been completely wiped up, and the area surrounding the engine is dry.

2.Throttle Lever — Used to adjust engine RPM speed (lever advanced forward SLOW, lever back toward operator FAST).

3.Engine ON/OFF Switch — ON position permits engine starting, OFF position stops engine operations.

4.Recoil Starter (pull rope) — Manual-starting method. Pull the starter grip until resistance is felt, then pull briskly and smoothly.

5.Fuel Valve Lever — OPEN to let fuel flow, CLOSE to stop the flow of fuel.

6.Choke Lever — Used in the starting of a cold engine, or in cold weather conditions. The choke enriches the fuel mixture.

7.Air Cleaner — Prevents dirt and other debris from entering the fuel system. Remove wing-nut on top of air filter cannister to gain access to filter element.

NOTICE

Operating the engine without an air filter, with a damaged air filter, or a filter in need of replacement will allow dirt to enter the engine, causing rapid engine wear.

WARNING

Engine components can generate extreme heat. To prevent burns, DO NOT touch these areas while the engine is running or immediately after operating. NEVER operate the engine with the muffler removed.

8.Spark Plug — Provides spark to the ignition system. Set spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch). Clean spark plug once a week.

9.Muffler — Used to reduce noise and emissions.

10.Fuel Tank — Holds unleaded gasoline. For additional information refer to engine owner's manual.

QP2TH TRASH PUMP • OPERATION AND PARTS MANUAL — REV. #5 (01/29/14) — PAGE 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents This Manual Must Accompany the Equipment AT ALL Times Model QP2THProposition 65 Warning QP2TH Trash Pump Operation and Parts Manual REV. #5 01/29/14 QP2TH Trash Pump Table of ContentsOrdering parts has never been easier Parts Ordering ProceduresSafety Messages Safety InformationSerious damage to the equipment or engine General SafetyPump Safety „ Never open the priming plug when pumpEngine Safety Fuel SafetyBefore servicing equipment Battery Safety Electric Start only Transporting Safety„ Use well-insulated gloves when picking up the battery Label must remain with the engine for its entire life Emissions InformationModel Specifications PumpSpecifications Pump Dry Net WeightEngine Specifications EngineSpecifications Engines DimensionGeneral Information QP2TH Pump Application Pump ComponentsBasic Engine Initial ServicingMuffler Used to reduce noise and emissions Season Inspection EngineBefore Starting Oil TypeSetup Place the engine fuel valve lever See to the on position Place the engine ON/OFF switch See in the on positionOperation Starting the EngineStopping the Engine Always run engine at full speed while pumpingPlace the fuel shut-off lever See in the OFF position Pump Vacuum Test Maintenance PumpAdjusting Impeller Clearance Pump CleaningPump Vacuum Tester First Every Maintenance EngineEngine Maintenance Engine Maintenance ScheduleEngine OIL Engine AIR CleanerDaily WeeklySpark Arrester Removal Spark Arrester CleaningPump Storage StorageOperation not satisfactory Troubleshooting EngineEngine Troubleshooting Symptom Possible Problem Solution Difficult to startTroubleshooting ENGINE/PUMP Pump TroubleshootingSymptom Possible Problem Solution Explanation of Code in Remarks Column Sample Parts ListQty Description Suggested Spare PartsPump Assembly 1889000132 18891000111889100020 1889100171Pump Assembly 0205490080 0151191257M12 X 57 X15 X 39# 0520030310 0204490060Engine Service Parts 28462ZH8003 17620ZH702317620Z4M000 28462ZE2W11Freight Policy Terms and Conditions of Sale PartsQP2TH Trash Pump Operation and Parts Manual REV. #5 01/29/14 HERE’S HOW to GET Help

QP2TH specifications

The Multiquip QP2TH is a versatile and efficient piece of equipment tailored for various applications, including construction, landscaping, and roadwork. This powerful equipment is designed to provide robust performance, easy maneuverability, and a range of features that make it a valuable addition to any job site.

One of the standout features of the QP2TH is its robust construction, which includes a heavy-duty frame designed to withstand the rigors of demanding work environments. The equipment is built with high-quality materials, ensuring longevity and reliability. The QP2TH is equipped with a reliable engine, offering sufficient power to tackle tough tasks while maintaining efficiency. This engine not only provides excellent performance but also ensures lower fuel consumption, making it an economic choice for operators.

The QP2TH boasts advanced technology that enhances its usability, including automated features that simplify operation. Its intuitive control panel allows operators to easily select settings, monitor performance, and troubleshoot issues with minimal downtime. Additionally, the machine features ergonomic controls designed to reduce operator fatigue, enabling longer working hours without compromising comfort.

Maneuverability is another defining characteristic of the Multiquip QP2TH. The compact design coupled with robust wheels allows for easy navigation across various terrains, including rugged landscapes and tight urban spaces. This versatility ensures that the QP2TH can perform effectively in a range of job applications, from grading and trenching to compacting and leveling.

Another noteworthy feature is the machine's ability to accommodate a variety of attachments and accessories. This adaptability makes the QP2TH suitable for multiple tasks, enhancing its effectiveness as a multifunctional tool on the job site. Whether operators need to switch from a compactor to a grader, the QP2TH can meet those needs swiftly and efficiently.

In conclusion, the Multiquip QP2TH is a powerful and adaptable machine equipped with significant features and technologies that enhance its performance and usability. With its durable construction, efficient engine, ergonomic controls, and versatility in attachments, the QP2TH stands out as an essential asset for professionals in the construction and landscaping industries.
Top Page Image Contents