Basic Operations

Surround Mode Buttons

Five buttons on the remote (2CH, PLC, PLM, 5CH, 7CH) and four buttons on the front panel (2CH, DOLBY PLII/3ST, DTS/Neo 6, DSP) allow direct selection of certain surround modes. The function of these buttons varies depending on the type of recording being played. See the Manually Selecting Surround Modes section for detailed information.

SUR+ Button

This button on the remote is used in conjunc- tion with the +/– buttons for manual selection of surround modes and features. See the Manu- ally Selecting Surround Modes section for in- formation.

DYN Button

Used the DYN button on the remote to select the dynamic range control setting in Dolby Digi- tal surround mode.

MENU/OSD Button

Push this button on the remote to turn on the OSD menu system. If the menu system is al- ready visible, push this button to cancel the display. Press and hold the button to turn off the front panel display.

ENTER Button

The ENTER button is used to confirm and memorize various settings in the setup and operation of the RSX-1056. Its use is described in detail in the relevant sections.

BAND Buttons

Press either of the BAND buttons to toggle be- tween AM and FM reception.

TUNING Buttons

The TUNING buttons (labeled CH UP/DOWN on the remote control) provide three different tuning functions, depending on the mode of operation: frequency tuning, preset tuning, or selection of an RDS/RBDS program type.

MEMORY Button

The front panel MEMORY button is used with the NUMERIC buttons to store station presets.

NUMERIC Buttons

The NUMERIC buttons on the front panel or the remote are used to enter the number of a memorized station preset or for direct entry of a station frequency.

DIRECT Button

FRQ DIRECT Button

The front panel DIRECT and remote control FRQ DIRECT buttons are used in conjunction with the NUMERIC buttons for direct entry of a sta- tion frequency in AM/FM tuning.

MONO Button

FM MONO Button

The front panel MONO and remote control FM MONO buttons change the FM mode from stereo reception to mono reception.

TUNE Button

PRESET Button

P-TUN Button

The TUNE, PRESET, and P-TUN buttons on the remote are used to select FREQUENCY tun- ing or PRESET tuning modes. The TUNE and PRESET buttons select the modes directly. The P-TUN button toggles between the two modes.

SCAN Button

Preset scan tuning automatically scans through the memorized station presets, playing each for 5 seconds. Press the SCAN button on the remote to begin preset scanning. Press the but- ton again to stop the scanning and listen to the desired preset.

RDS/RBDS Buttons

Four remote control buttons (DISP, PTY, TP, TA) are used to activate various RDS/RBDS tun- ing features. See the RDB/RBDS Tuning sec- tion of the manual for detailed information.

English

This section covers the basic operating con- trols of the RSX-1056 and the remote.

Power and Standby On/Off

The rear panel POWER switch on the RSX-1056 is a master power switch. The button must be in the ON position for the unit to operate. When it is in the OFF position, the unit is fully off and cannot be activated from the front panel or remote control.

In normal operation, the rear panel POWER switch is always left in the ON position. The RSX-1056 is activated and deactivated using the front panel STANDBY button, the remote control POWER button, or the remote ON/ OFF buttons. When activated, the RSX-1056 is fully functional and the front panel display illuminated. When deactivated, the unit goes into a standby mode, with minimal power applied to the microprocessor.

NOTE: When the unit has AC power applied and the rear panel POWER switch is on, the front panel STANDBY LED lights, regardless of whether the unit is in standby mode or activated.

The front panel STANDBY button and the re- mote control POWER button function as toggle switches. Press either button to activate the unit. Press either button again to put the unit in standby mode.

The ON/OFF buttons on the remote serve the same function, but provide discrete ON (ac- tive) or OFF (standby) commands.

When using the Zone 2 capability of the RSX-1056, the standby activation is com- pletely independent for the main room and Zone 2. ON/OFF commands sent from the remote in the main room will not affect Zone

2.Pressing the ON/OFF buttons on a remote located in Zone 2 will only affect that zone and not the main room. When the unit is ac- tivated in ZONE 2, the ZONE 2 LED on the front panel is lit.

There are three available power mode options, which may be useful in configuring the RSX-1056 for special system configurations. See the Other Options menu in the Setup section of this manual for additional details on changing the default standby behavior.