Rotel RSX-1056 owner manual Zone 2 Setup, Default Setup, To change the Front Redirect setting

Page 43

43

English

Change settings on the OTHER OPTIONS menu by highlighting the desired line using the UP/ DOWN buttons and using the +/– buttons to step through the available settings. To return to the MAIN menu, press the ENTER button. Press the MENU/OSD button on the remote to cancel the display and return to normal operation.

Zone 2 Setup

ZONE2 SETUP

SOURCE:Off

VOLUME SETUP:Variable

VOLUME:60

TURN ON VOL:Last

MAX VOL:Max

12V TRIGGER:Off

MAIN MENU

The ZONE 2 SETUP menu provides settings and configuration options related to the op- eration of Zone 2. This menu is reached by highlighting the ZONE 2 line on the MAIN menu and pressing ENTER.

SOURCE: Specifies a source for listening in Zone 2. Options are CD, TUNER, TAPE, VIDEO 1–5, SOURCE, and OFF. Selecting the SOURCE option links the Zone 2 source to the source selected for the main zone so that Zone 2 will hear the same source as the main zone. Selecting the OFF option turns Zone 2 off.

VOLUME SETUP: configures the Zone 2 outputs for VARIABLE or FIXED volume levels. VARIABLE allows control of the volume settings in Zone 2 from the RSX-1056 front panel or from a remote control/IR repeater in Zone 2. FIXED output disables the Zone 2 volume control. In this mode, the Zone 2 level can be fixed at the level specified on the next line, thus optimizing system performance when send- ing a fixed level signal to a preamp or ampli- fier with its own volume adjustment.

VOLUME: In VARIABLE output mode, this line shows the current volume setting for Zone 2. In FIXED output mode, this volume setting es- tablishes a permanent fixed output level for Zone 2.

Move the highlight to the desired line using the UP/DOWN buttons and use the +/– but- tons to adjust the volume level. To return to the MAIN menu, press the ENTER button. Press the MENU/OSD button on the remote to cancel the display and return to normal operation.

TURN ON VOL: Specifies a default volume level to be used each time Zone 2 is activated. You can select LAST to have Zone 2 activate with the last previously used volume setting. Or, you specify a volume from MIN (full mute) to MAX, in 1dB increments. Note that this setting cannot exceed the MAX VOL established in the next line of the menu.

MAX VOL: Specifies the maximum volume level for Zone 2. The volume cannot be ad- justed above this level. Settings range from MIN to MAX, in 1dB increments.

12V TRIGGER: The RSX-1056 has three12V trigger outputs that supply a 12V DC signal to turn on Rotel components and other com- ponents as needed. The 12V Trigger labeled ZONE 2 is assigned to Zone 2 and can send a turn-on signal to remote components when- ever Zone 2 is activated. Select the appropri- ate setting from eight options to have the ZONE 2 trigger output send the turn-on signal. The options that will activate the Zone 2 trigger are: zone, 1+zone, 2+zone, and ALL. The options that will disable the Zone 2 trigger are: 1, 2, 1+2, and No.

Default Setup

DEFAULT SETUP

TUNER SETTING:N.America

FRONT REDIRECT:Front

FACTORY DEFAULT:No

USER DEFAULT:No

SET USER DEFAULT:No

MAIN MENU

The DEFAULT SETUP menu provides access to six functions:

•Set the tuning function for North American or European frequencies.

•Redirect the front channel amplifiers to power center back speakers or speakers in Zone 2 speakers.

•Restore all features and settings to the origi- nal FACTORY DEFAULT settings.

•Memorize a custom group of settings as a USER DEFAULT.

•Activate the memorized USER DEFAULT set- tings.

To change the TUNER setting: Place the highlight on the TUNER SETTING line using the UP/DOWN buttons and use the +/– but- tons to change the setting to N. AMERICA or EUROPE. Then, move the highlight to the FAC- TORY DEFAULT line and change the setting to YES as described above. The screen will change to a confirmation screen. Press the EN- TER button to proceed with resetting the FAC- TORY DEFAULT settings and changing the TUNER SETTING. To return to the MAIN menu without resetting the FACTORY DEFAULT and TUNER settings, change the entry to NO and press the ENTER button.

To change the FRONT REDIRECT setting:

Place the highlight on the FRONT REDIRECT line using the UP/DOWN buttons and use the +/– buttons to change the setting to FRONT SP (for powering front speakers), CB SP (for powering center back speakers), or ZONE SP (for powering speakers in zone 2). If you re- direct the internal amplifiers, then you will need a separate stereo amplifier to drive your front speakers.

NOTE: Changing the default TUNER SETTING or REDIRECT SETTING can only done at the same time as restoring the FACTORY DEFAULT settings. Therefore, we recommend selecting your default TUNER and REDIRECT settings and resetting to the FACTORY DEFAULT set- tings as the first step in configuring the unit, before you change or memorize any other configuration settings.

To restore the FACTORY DEFAULT set-

tings: Place the highlight on the FACTORY DEFAULT line using the UP/DOWN buttons and use the +/– buttons to change the setting to YES. Press the ENTER button to proceed with resetting the FACTORY DEFAULT settings. The unit will power off and then on, with the fac- tory settings restored. To return to the MAIN menu without resetting the FACTORY DEFAULT settings, change the entry to NO and press the ENTER button.

NOTE: Resetting to factory default settings will erase all stored settings including delay set- tings, speaker settings, balance settings, in- put settings and more. You will lose ALL system configuration settings. Be certain that you wish to do so before resetting the factory defaults.

Page 42 Page 44
Image 43
Page 42 Page 44
Contents RSX-1056 10 cm FCC Information Important Safety InstructionsControls and Connections RSX-1056Surround Sound ReceiverRR-1050 Remote EnglishRSX-1056 Surround Sound Receiver Connecting the SpeakersConnecting Cable, Satellite, or Hdtv Connecting the TVConnecting a CD Player/CDR Recorder Connecting a VCRConnecting a DVD Player Connecting an Audio RecorderConnecting AM and FM antennae Connecting a DVD-A or Sacd PlayerHF CONTOUR+5 LF Contour Main Menu On-Screen MenusContents Menu Basics SpecificationsUnpacking Key FeaturesTape Outputs PlacementCD Inputs Tape InputsMulti Inputs Video 1-5 Audio InputsVideo 1-3 Audio Outputs Speaker OutputsDigital Audio Input & Outputs Other Connections Audio Recorder DVD PlayerDVD-A or Sacd Player Speakers Connecting a SubwooferRedirect Feature TV MonitorFront-panel Display Front Panel OverviewAM Antenna FM AntennaSLT Button Standby Button Power ButtonUsing the RR-1050 Audio Button Volume Knob Volume ButtonBasic Operations Selecting Inputs DTS DTS 96/24 Overview Surround FormatsDolby Surround Dolby Pro Logic Dolby DigitalDolby Pro Logic 7.1 Channel Surround DTS Neo6Dolby Digital Surround EX 7.1 Channel SurroundManually Selecting Surround Modes ModesDolby Digital 2.0 discs Dolby Digital 5.1 discs Dolby Digital Surround EX discsDTS 5.1 discs DTS 96/24 discs DTS-ES 6.1 discs Digital Stereo discs PCM, MP3, and Hdcd Mpeg Multichannel discsAnalog Stereo Dynamic Range Other SettingsGroup Delay Speaker LevelTuner Controls Contour/Tone SettingsTo adjust the contour settings from the remote Normal Frequency tuningNumeric Buttons Station Presets TA Button Disp ButtonPTY Button TP ButtonControlling Zone 2 from the Remote Location Zone 2 Power On/OffZone 2 Operation Controlling Zone 2 from the Main RoomNavigation Buttons Menu BasicsSystem Status Input Setup Configuring InputsMain Menu Dolby Pro Logic II Multi Input SetupUnderstanding Speaker Configuration ConfiguringAdvance Speaker Setup Speaker SetupCrossover 40Hz/60Hz/80Hz/ 100Hz/120Hz/150Hz/200Hz/OFF Subwoofer SetupTest Tone Delay SetupCalibration with an SPL meter Other Options Contour SetupSpeaker front/center/surround/cen To restore the Factory Default set Zone 2 SetupDefault Setup To change the Front Redirect settingTroubleshooting Specifications Rotel Europe Rotel of AmericaRotel Deutschland
Top Page Image Contents