FoodSaver 18-0163 user manual Air Was Removed From the Bag, But Has Come Back Into the Bag

Page 18

T H E F O O D S AV E R U S E R M A N U A L

Troubleshooting

Air Was Removed From the Bag, But Has Come Back Into the Bag:

1Check the seal of the bag. There may be a wrinkle in the bag along the seal, which caused leakage and allowed air to come back into the bag. Cut the bag open and vacuum package it again.

2Moisture or food material (i.e. juices, grease, crumbs, powders, etc.) along the seal may have caused leakage and allowed air to come back into the bag. Cut the bag open, wipe the top inside of the bag material to clear away any moisture or food residue, then vacuum package the bag again. See the “Food Preparation and Storage Guide” in this User Manual for guidelines for specific foods.

3Food items with sharp edges may have punctured the bag. If you find a puncture hole, you will need to use a new FoodSaver Bag. Make sure to protect the bag from puncture holes by wrapping the items in cushioning material such as a paper towel.

4If you find none of these conditions identified in 1-3 (above), and the bag appears to have air inside, fermentation or the release of natural gases from inside the foods may have occurred. This could indicate that the food may have begun to spoil and should be discarded.

The Bag Melts:

1The Sealing Strip may have become too hot. Always wait at least 20 seconds for the Vac 1200 to cool down before vacuuming and/or sealing another bag.

T H E F O O D S AV E R U S E R M A N U A L

The Bag Will Not Seal:

1Wait 20 minutes to allow the Vac 1075 to cool off, then try using it again. The appliance will shut off automatically if it becomes too hot. To help prevent the appliance from becoming too hot:

a.Wait at least 20 seconds for the appliance to cool down after vacuum packaging and/or sealing before attempting to vacuum and/or seal another bag.

b.Keep the lid open before vacuuming and/or sealing another bag.

The Mason Jar Will Not Vacuum:

1Make sure the Jar Sealer is centered and pressed firmly over the lid on the mason jar.

2Make sure the rubber gasket on the mason jar lid is free from food materials, crumbs, etc.

3Make sure the rim of the mason jar does not have any cracks or scratches. Any gaps can prevent a vacuum from forming.

4Make sure you aren’t filling the mason jar too full prior to vacuum packaging. Always leave at least one inch (1") between the contents and the lid.

5Make sure the metal lid of the mason jar is not bent.

32

33

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Vac1200 Table of Contents WelcomeFoodSaver Vac FoodSaver Accessories Important Safeguards Important TipsHow to Make a Custom-Made Bag with FoodSaver Rolls Close the lidClose the lid How to Use the Sealing Time Adjustment Switch How to Use the Extended Vacuum ButtonHow to Use the Instant Seal Button How to Vacuum Package Using FoodSaver Designer Canisters Place the lid on top of the canisterHow to Open the FoodSaver Bulk Storage or Square Canister How To Vacuum Package Using FoodSaver Universal Lids Wash bags in warm water using a mild dishwashing soap How to Vacuum Package Using FoodSaver Bottle StoppersCare and Cleaning Instructions Allow bags to dry thoroughly before reusingFood Preparation and Storage Guide Stops the enzyme action, which Vegetables should be blanchedPlace baking sheet in the freezer Color and textureInto the vacuum pump and help guarantee a good seal Each time the bag will be opened and repackagedMaterial, like a paper towel. This Troubleshooting Vacuum Packaging Non-Food ItemsAir Was Removed From the Bag, But Has Come Back Into the Bag FoodSaver Designer Canister Will Not Vacuum Warranty and Service Information
Top Page Image Contents