Kawasaki J8472PR, K0450 manual Battery Care and Disposal

Page 16

BATTERY CARE AND DISPOSAL

Care

If a battery leak develops, avoid contact with the leaking acid and place the damaged battery in a plastic bag. See information below for proper disposal.

If acid comes in contact with skin or eyes, flush with cool water for at least 15 minutes and call a physician.

If acid is internally ingested, give water, milk of magnesia or egg whites immediately. Never give emetics or induce vomiting. Call

a physician.

•Charge a new battery for at least 18 hours before first use. Never charge the battery longer than 30 hours. Overcharging or undercharging the battery may shorten battery life and decrease vehicle running time.

•After the first charge, recharge the battery for at least 14 hours after each use. Never charge the battery longer than 30 hours. Charge the battery after each use, regardless of how long the vehicle was used.

•The battery must be upright while charging.

•Do not allow the battery to run down completely before charging.

•Charge the battery before storing the vehicle.

•Charge the battery at least once per month, even if the vehicle has not been used.

•Leaving the battery in a discharged condition will ruin it.

•Always remove an exhausted battery from the vehicle. Battery leakage and corrosion can damage the vehicle.

•Do not store the battery on a surface (such as a kitchen counter top) which could be damaged by the acid contained inside the battery. Take precautions to protect the surface on which you store the battery.

•Do not store the battery in temperatures above 75° F or below -10° F.

•Use only a Power Wheels® 12 volt battery. Remember to charge the new battery for at least 18 hours before first use.

•Prevent the battery from moving freely inside the battery compart- ment. Always use the battery retainer to secure the battery in the battery compartment.

•Examine the battery, charger and their connectors for excessive wear or damage each time you charge the battery. If damage is detected, do not use the charger or the battery until you have replaced the worn or damaged part.

Disposal

•Your Power Wheels® battery is a non-spillable, sealed lead-acid battery. It must be recycled or disposed of in an environmentally sound manner.

•Do not dispose of a lead-acid battery in a fire. The battery may explode or leak.

•Do not dispose of a lead-acid battery in your regular, household trash. The incineration, landfilling or mixing of sealed lead-acid batteries with household trash is prohibited by law in most areas.

•Protect the environment by not disposing of this product with household waste (2002/96/EC). Check your local authority for recycling advice and facilities (Europe only).

•Return an exhausted battery to a federal or state approved lead- acid battery recycler, such as a Power Wheels® authorized service center or a local seller of automotive batteries. For the authorized service center location nearest to you, please visit us on-line at www.powerwheels.com or call 1-800-348-0751. Contact your local waste management officials for other information regarding the environmentally sound collection, recycling and disposal of lead-acid batteries. If you live in the State of Florida or the State of Minnesota, it is prohibited by law for anyone to throw away lead-acid batteries in the municipal waste stream.

16

J8472pr-0920

Page 15 Page 17
Image 16
Page 15 Page 17
Contents With Assembly Instructions For Models J8472 and K0450 Table of Contents Important InformationElectrical Hazard HandlebarSeat Vehicle Steering Column Cap Plate PartsFront Clip Hubcaps Wheel Covers Bushings Rear Axle Volt BatteryFor your convenience, we included extra fasteners Parts Picture Battery Charging Or callBattery Charger Connector AssemblyRear Axle Cotter Pin Motor Assembly Wheel R Motor Assembly Rear Axle AssemblySlots Up BushingTurn the vehicle upright Steering Column ConnectorsSteering Column Wheel L Washer Front Axle BushingCotter Pin Front Axle Fit a cotter pin into the hole on the end of the front axleBrush Guard Hand GripFit both hand grips on the ends of the handlebar Locate the opening under the drive buttonsDecoration Seat Drive ButtonsFor Model J8472 For Model K0450 Battery Installation Seat Battery RetainerPower Wheels Seat Drive Buttons Motor Harness ConnectorBattery Care and Disposal CareAlways sit on the seat Always wear shoes Safe Driving RulesTo disconnect the motor harness Vehicle Operation DrivePress the Drive button on the tank ReverseVehicle Care Charge IndicatorButton Problems and Solutions Problem Possible Cause SolutionShort run time Less than Undercharged battery Operation of the drive system by raising the rear wheels off Limited Warranty Bumper-to-Bumper Limited WarrantyBefore first-time use You must charge the battery Hours

J8472, J8472PR, K0450 specifications

The Kawasaki K0450, J8472PR, and J8472 are characterized by advanced engineering and impressive technological features aimed at optimizing performance and enhancing user experience. These models are backed by Kawasaki’s commitment to innovation and reliability, making them a standout choice in their respective categories.

The Kawasaki K0450 is a powerhouse that offers a combination of robust performance and fuel efficiency. It is equipped with a cutting-edge, high-torque engine designed for optimal power delivery, making it suitable for a variety of applications, from landscaping to construction tasks. The K0450’s compact design ensures ease of maneuverability, while its durable construction promises longevity, even under heavy use in challenging environments.

The J8472PR model, on the other hand, is known for its innovative technology that emphasizes precision and efficiency. It features an advanced control system that allows users to tailor performance settings according to specific needs. This model comes with eco-friendly technology, significantly reducing emissions without compromising power. Additionally, the ergonomic design ensures user comfort, reducing fatigue during extended use.

With the J8472 model, Kawasaki continues its tradition of excellence by integrating modern features that enhance productivity. Notable characteristics include its high-grade materials that ensure longevity and resilience, as well as a user-friendly interface that simplifies operation. Its cutting-edge safety features provide assurance to users, making it a reliable choice in demanding conditions.

All three models showcase Kawasaki's dedication to quality and technological advancement. The incorporation of advanced diagnostics systems allows for easy maintenance and timely troubleshooting, thereby minimizing downtime. Furthermore, these models are backed by Kawasaki's extensive support network, ensuring users have access to assistance whenever required.

In summary, the Kawasaki K0450, J8472PR, and J8472 exemplify what modern engineering can achieve. With their impressive blend of performance, efficiency, and user-oriented features, they stand as premier choices for anyone seeking reliable, high-quality machinery. Whether for professional applications or personal projects, these models are designed to deliver unparalleled results.
Top Page Image Contents