Kawasaki J8472PR, K0450 manual Operation of the drive system by raising the rear wheels off

Page 22

PROBLEM

POSSIBLE CAUSE

SOLUTION

Vehicle runs in low speed, but

High speed hook-up not disconnected.

The vehicle was pre-set to run only in low speed. To allow the

does not run in high speed.

 

vehicle to run in low and high speed, you must connect the High

Please note: The vehicle is

 

Speed connectors. Follow the instructions on page 18.

 

Note: The high speed connectors must be joined to use the

designed to operate in low

 

speed only in reverse.

 

high speed grip.

When the foot pedal is pressed

Operation of vehicle in low speed

It is possible that only one rear wheel may spin when both rear

one rear wheel spins

 

wheels are raised off the ground and the vehicle is in low speed.

 

 

This does not necessarily indicate a problem. Check for proper

 

 

operation of the drive system by raising the rear wheels off the

 

 

ground and pressing the foot pedal. If only one rear wheel spins,

 

 

carefully press your hand on the spinning wheel to slow it down.

 

 

The other rear wheel should begin to spin. If the other rear wheel

 

 

does not begin to spin, there may be a problem with the vehicle.

 

 

Contact your local Power Wheels® authorized service center for

 

 

diagnosis and repair.

Sometimes the vehicle doesn’t

Loose wire or connector

Check all wires around the motors and all connectors to make

run, but other times it does

 

sure they are tight.

 

Motor or electrical switch damage

Contact your local Power Wheels® authorized service center for

 

 

diagnosis and repair.

When the foot pedal is

Loose wire or connector

Check all wires around the motors and all connectors to make

pressed, the vehicle won’t run

 

sure they are tight.

without a push

 

 

 

“Dead Spot” on motor

Contact your local Power Wheels® authorized service center for

 

 

diagnosis and repair.

Battery's thermal fuse

Damaged battery

Contact your local Power Wheels® authorized service center for

constantly "trips", but the

 

diagnosis and repair.

vehicle is not overloaded

 

 

nor the driving conditions

 

 

too severe

 

 

 

Child is switching between FORWARD

Teach your child to stop the vehicle before switching direction.

 

and REVERSE without stopping

 

Loud clacking or grinding noise

Broken gears

Contact your local Power Wheels® authorized service center for

from a motor-gearbox

 

diagnosis and repair.

Charger gets warm during use

It is normal for some chargers to get

No action required.

 

warm during use and is not reason for

 

 

concern.

 

 

 

If your charger does not get warm during use, it does not mean

 

 

that it is not working properly.

Battery makes a sizzling or

It is normal for some batteries to make

No action required.

gurgling noise when charging

noise and swell slightly while charging

 

 

and is not reason for concern.

 

 

 

If your battery does not make noise or swell slightly during

 

 

charging, it does not mean that it is not accepting the charge.

22

J8472pr-0920

Page 21 Page 23
Image 22
Page 21 Page 23
Contents With Assembly Instructions For Models J8472 and K0450 Table of Contents Important InformationElectrical Hazard HandlebarSeat Vehicle Steering Column Cap Plate PartsFront Clip Hubcaps Wheel Covers Bushings Rear Axle Volt BatteryFor your convenience, we included extra fasteners Parts Picture Battery Charging Or callBattery Charger Connector AssemblyRear Axle Cotter Pin Slots Up Motor Assembly Wheel RMotor Assembly Rear Axle Assembly BushingTurn the vehicle upright Steering Column ConnectorsSteering Column Cotter Pin Front Axle Wheel LWasher Front Axle Bushing Fit a cotter pin into the hole on the end of the front axleFit both hand grips on the ends of the handlebar Brush GuardHand Grip Locate the opening under the drive buttonsDecoration Seat Drive ButtonsFor Model J8472 For Model K0450 Power Wheels Battery InstallationSeat Battery Retainer Seat Drive Buttons Motor Harness ConnectorBattery Care and Disposal CareAlways sit on the seat Always wear shoes Safe Driving RulesTo disconnect the motor harness Press the Drive button on the tank Vehicle OperationDrive ReverseVehicle Care Charge IndicatorButton Problems and Solutions Problem Possible Cause SolutionShort run time Less than Undercharged battery Operation of the drive system by raising the rear wheels off Limited Warranty Bumper-to-Bumper Limited WarrantyBefore first-time use You must charge the battery Hours

J8472, J8472PR, K0450 specifications

The Kawasaki K0450, J8472PR, and J8472 are characterized by advanced engineering and impressive technological features aimed at optimizing performance and enhancing user experience. These models are backed by Kawasaki’s commitment to innovation and reliability, making them a standout choice in their respective categories.

The Kawasaki K0450 is a powerhouse that offers a combination of robust performance and fuel efficiency. It is equipped with a cutting-edge, high-torque engine designed for optimal power delivery, making it suitable for a variety of applications, from landscaping to construction tasks. The K0450’s compact design ensures ease of maneuverability, while its durable construction promises longevity, even under heavy use in challenging environments.

The J8472PR model, on the other hand, is known for its innovative technology that emphasizes precision and efficiency. It features an advanced control system that allows users to tailor performance settings according to specific needs. This model comes with eco-friendly technology, significantly reducing emissions without compromising power. Additionally, the ergonomic design ensures user comfort, reducing fatigue during extended use.

With the J8472 model, Kawasaki continues its tradition of excellence by integrating modern features that enhance productivity. Notable characteristics include its high-grade materials that ensure longevity and resilience, as well as a user-friendly interface that simplifies operation. Its cutting-edge safety features provide assurance to users, making it a reliable choice in demanding conditions.

All three models showcase Kawasaki's dedication to quality and technological advancement. The incorporation of advanced diagnostics systems allows for easy maintenance and timely troubleshooting, thereby minimizing downtime. Furthermore, these models are backed by Kawasaki's extensive support network, ensuring users have access to assistance whenever required.

In summary, the Kawasaki K0450, J8472PR, and J8472 exemplify what modern engineering can achieve. With their impressive blend of performance, efficiency, and user-oriented features, they stand as premier choices for anyone seeking reliable, high-quality machinery. Whether for professional applications or personal projects, these models are designed to deliver unparalleled results.
Top Page Image Contents