Kawasaki K0450, J8472PR manual Safe Driving Rules, Always sit on the seat Always wear shoes

Page 17

SAFE DRIVING RULES

RIDING HAZARD

WARNING

Prevent Injuries and Deaths

Direct Adult Supervision Required.

Never Ride at Night.

Keep Children Within Safe Riding Areas. These areas must be:

-away from swimming pools and other bodies of water to prevent drownings

-generally level to prevent tipovers

-away from steps, steep inclines, cars, roads and alleys.

Riding Rules

Make sure children know and follow these rules for safe driving and riding.

-Always sit on the seat.

-Always wear shoes.

-Only 1 (one) rider at a time.

Restrict your child's driving to areas that are generally level.

Teach Safety Rules to Children

While children can quickly develop the skill necessary to drive this vehicle, it is important to remember that their judgment skills are still very immature. Unsupervised driving by children can lead to serious injury. Before children use this vehicle, an adult should carefully evaluate the driving area as well as the children’s skill level and ability to drive this vehicle safely. Children are not always able to recognize or anticipate hazards, even when they have been taught about them. There is no acceptable substitute for direct adult supervision.

Teach appropriate safety rules to your child before allowing operation of this vehicle. These rules should also be reviewed with neighborhood children or other playmates who want to drive this vehicle.

Riding Rules

Make sure children know and follow these rules for safe driving:

1.Always sit on the seat.

2.Always wear shoes.

3.Only 1 (one) rider at a time. A child who is not sitting on the seat or who is standing on the vehicle could fall off, cause a tip-over or block the driver’s view. A child could be seriously injured.

4.Do not allow any child to drive the vehicle in the street or near moving (motorized) vehicles.

5.Do not allow any child to drive near bodies of water (such as pools or creeks), obstructions (such as furniture, low tree limbs or play equipment), or drop-offs (such as stairs or decks).

6.Do not allow any child to drive the vehicle in the dark. A child could encounter unexpected obstacles and have an accident. Operate the vehicle only in the daytime or a well-lit area.

7.Restrict your child's driving to areas that are generally level with gentle inclines or slopes.

8.Do not allow your child to drive down or across a steep slope.

-The vehicle may gain unsafe speed, even if the pedal is released to stop.

-The vehicle may tilt and tip over.

-The wheels could lose traction, causing the vehicle to slip.

9.Do not allow your child to drive up steep inclines. The motor may stop and the vehicle could roll backwards at an unsafe speed.

10.Never put anything near any moving parts. Rotating parts such as motors, gear boxes and wheels can snag fingers, hair, etc., causing serious injury. Do not allow operation of the vehicle when it is on its side or in an upside-down position.

11.Do not operate the vehicle near flammable vapors (gasoline, paint thinner, acetone, liquid wax, etc.). The vehicle’s electrical switches, like most electrical switches, emit an internal spark when first turned on or turned off. The presence of flammable liquids or vapors could cause an explosion or a fire. Keep all flammable products in tightly sealed containers and away from the vehicle.

12.Do not allow a child to operate the vehicle without direct adult supervision. To prevent unsupervised use of the vehicle, disconnect the motor harness from the battery when the vehicle is not in use.

To disconnect the motor harness:

-Press the rear tab on the seat and lift to remove.

-Lift the battery retainer to access the battery compartment.

-Pull the motor harness connector from the battery.

-Lift the battery retainer and slowly lower the battery into the compartment.

-Replace the seat on the vehicle.

17

J8472pr-0920

Image 17
Contents With Assembly Instructions For Models J8472 and K0450 Important Information Table of ContentsElectrical Hazard Front Clip PartsHandlebarSeat Vehicle Steering Column Cap Plate For your convenience, we included extra fasteners Rear Axle Volt BatteryHubcaps Wheel Covers Bushings Parts Picture Or call Battery ChargingRear Axle Cotter Pin AssemblyBattery Charger Connector Motor Assembly Rear Axle Assembly Motor Assembly Wheel RSlots Up BushingSteering Column Steering Column ConnectorsTurn the vehicle upright Washer Front Axle Bushing Wheel LCotter Pin Front Axle Fit a cotter pin into the hole on the end of the front axleHand Grip Brush GuardFit both hand grips on the ends of the handlebar Locate the opening under the drive buttonsSeat Drive Buttons DecorationFor Model J8472 For Model K0450 Seat Battery Retainer Battery InstallationPower Wheels Seat Drive Buttons Motor Harness ConnectorCare Battery Care and DisposalTo disconnect the motor harness Safe Driving RulesAlways sit on the seat Always wear shoes Drive Vehicle OperationPress the Drive button on the tank ReverseButton Charge IndicatorVehicle Care Problem Possible Cause Solution Problems and SolutionsShort run time Less than Undercharged battery Operation of the drive system by raising the rear wheels off Bumper-to-Bumper Limited Warranty Limited WarrantyBefore first-time use You must charge the battery Hours

J8472, J8472PR, K0450 specifications

The Kawasaki K0450, J8472PR, and J8472 are characterized by advanced engineering and impressive technological features aimed at optimizing performance and enhancing user experience. These models are backed by Kawasaki’s commitment to innovation and reliability, making them a standout choice in their respective categories.

The Kawasaki K0450 is a powerhouse that offers a combination of robust performance and fuel efficiency. It is equipped with a cutting-edge, high-torque engine designed for optimal power delivery, making it suitable for a variety of applications, from landscaping to construction tasks. The K0450’s compact design ensures ease of maneuverability, while its durable construction promises longevity, even under heavy use in challenging environments.

The J8472PR model, on the other hand, is known for its innovative technology that emphasizes precision and efficiency. It features an advanced control system that allows users to tailor performance settings according to specific needs. This model comes with eco-friendly technology, significantly reducing emissions without compromising power. Additionally, the ergonomic design ensures user comfort, reducing fatigue during extended use.

With the J8472 model, Kawasaki continues its tradition of excellence by integrating modern features that enhance productivity. Notable characteristics include its high-grade materials that ensure longevity and resilience, as well as a user-friendly interface that simplifies operation. Its cutting-edge safety features provide assurance to users, making it a reliable choice in demanding conditions.

All three models showcase Kawasaki's dedication to quality and technological advancement. The incorporation of advanced diagnostics systems allows for easy maintenance and timely troubleshooting, thereby minimizing downtime. Furthermore, these models are backed by Kawasaki's extensive support network, ensuring users have access to assistance whenever required.

In summary, the Kawasaki K0450, J8472PR, and J8472 exemplify what modern engineering can achieve. With their impressive blend of performance, efficiency, and user-oriented features, they stand as premier choices for anyone seeking reliable, high-quality machinery. Whether for professional applications or personal projects, these models are designed to deliver unparalleled results.