Kawasaki K0450, J8472PR manual Short run time Less than Undercharged battery

Page 21

PROBLEM

POSSIBLE CAUSE

SOLUTION

Short run time (Less than

Undercharged battery

Charge the battery. A new battery should have been charged for at

1 - 3 hours per charge)

 

least 18 hours before using the vehicle for the first time. After first-

 

 

time use, recharge the battery for at least 14 hours after each use.

 

 

Never charge the battery longer than 30 hours.

 

 

Check all wires and connectors. Make sure the charger connector

 

 

is plugged into the battery, and that the charger is plugged into

 

 

the wall.

 

 

Make sure power flow to the wall outlet is “ON”.

 

Overcharged battery

Do not charge the battery longer than 30 hours. If you suspect

 

 

that your battery is damaged as a result of overcharging, contact

 

 

your local Power Wheels® authorized service center. They can test

 

 

your battery for you.

 

Battery is old and will not accept

Even with proper care, a rechargeable battery does not last

 

full charge

forever. Average battery life is 1 to 3 years depending on vehicle

 

 

use and use conditions. Replace the battery with a new Power

 

 

Wheels® 12 volt rechargeable battery. Do not substitute parts.

 

Tripped thermal fuse

The built-in thermal fuse may “trip” and shut down operation of the

 

 

vehicle if the vehicle is overloaded or the driving conditions too

 

 

severe. Once a fuse has “tripped”, remove your foot from the pedal

 

 

and wait approximately 25 seconds before operating the vehicle

 

 

again. To avoid repeated automatic shutdowns, do not overload

 

 

the vehicle by exceeding the 65 lbs (29.5 kg) maximum weight

 

 

capacity or by towing anything behind the vehicle. Do not drive

 

 

up hills or run into fixed objects, which can cause the wheels to

 

 

stop spinning while power is still being supplied to the motors. If

 

 

a thermal fuse continually trips, contact your local Power Wheels®

 

 

authorized service center.

Vehicle runs sluggishly

Undercharged battery

Charge the battery. A new battery should have been charged for at

 

 

least 18 hours before using the vehicle for the first time. After first-

 

 

time use, recharge the battery for at least 14 hours after each use.

 

 

Never charge the battery longer than 30 hours.

 

 

Check all connectors. Make sure the charger connector is plugged

 

 

into the battery, and that the charger is plugged into the wall.

 

 

Make sure power flow to the wall outlet is “ON”.

 

Battery needs charging

Be sure to charge the battery after each use.

 

Battery is old and will not accept

Even with proper care, a rechargeable battery does not last forever.

 

full charge

Average battery life is 1 to 3 years depending on the vehicle use

 

 

and use conditions. Replace the battery with a new Power Wheels®

 

 

12 volt rechargable battery. Do not substitute parts.

 

Vehicle is overloaded

Make sure you do not overload the vehicle by allowing more than

 

 

one rider at one time, by exceeding the 65 lbs (29.5 kg) maximum

 

 

weight capacity, or by towing objects behind the vehicle.

 

Driving conditions are too stressful

Restrict your child's driving to areas that are generally level with

 

 

gentle inclines or slopes.

21

J8472pr-0920

Page 20 Page 22
Image 21
Page 20 Page 22
Contents With Assembly Instructions For Models J8472 and K0450 Important Information Table of ContentsElectrical Hazard Parts HandlebarSeat Vehicle Steering Column Cap PlateFront Clip Rear Axle Volt Battery Hubcaps Wheel Covers BushingsFor your convenience, we included extra fasteners Parts Picture Or call Battery ChargingAssembly Battery Charger ConnectorRear Axle Cotter Pin Motor Assembly Rear Axle Assembly Motor Assembly Wheel RSlots Up BushingSteering Column Connectors Turn the vehicle uprightSteering Column Washer Front Axle Bushing Wheel LCotter Pin Front Axle Fit a cotter pin into the hole on the end of the front axleHand Grip Brush GuardFit both hand grips on the ends of the handlebar Locate the opening under the drive buttonsSeat Drive Buttons DecorationFor Model J8472 For Model K0450 Seat Battery Retainer Battery InstallationPower Wheels Seat Drive Buttons Motor Harness ConnectorCare Battery Care and DisposalSafe Driving Rules Always sit on the seat Always wear shoesTo disconnect the motor harness Drive Vehicle OperationPress the Drive button on the tank ReverseCharge Indicator Vehicle CareButton Problem Possible Cause Solution Problems and SolutionsShort run time Less than Undercharged battery Operation of the drive system by raising the rear wheels off Bumper-to-Bumper Limited Warranty Limited WarrantyBefore first-time use You must charge the battery Hours

J8472, J8472PR, K0450 specifications

The Kawasaki K0450, J8472PR, and J8472 are characterized by advanced engineering and impressive technological features aimed at optimizing performance and enhancing user experience. These models are backed by Kawasaki’s commitment to innovation and reliability, making them a standout choice in their respective categories.

The Kawasaki K0450 is a powerhouse that offers a combination of robust performance and fuel efficiency. It is equipped with a cutting-edge, high-torque engine designed for optimal power delivery, making it suitable for a variety of applications, from landscaping to construction tasks. The K0450’s compact design ensures ease of maneuverability, while its durable construction promises longevity, even under heavy use in challenging environments.

The J8472PR model, on the other hand, is known for its innovative technology that emphasizes precision and efficiency. It features an advanced control system that allows users to tailor performance settings according to specific needs. This model comes with eco-friendly technology, significantly reducing emissions without compromising power. Additionally, the ergonomic design ensures user comfort, reducing fatigue during extended use.

With the J8472 model, Kawasaki continues its tradition of excellence by integrating modern features that enhance productivity. Notable characteristics include its high-grade materials that ensure longevity and resilience, as well as a user-friendly interface that simplifies operation. Its cutting-edge safety features provide assurance to users, making it a reliable choice in demanding conditions.

All three models showcase Kawasaki's dedication to quality and technological advancement. The incorporation of advanced diagnostics systems allows for easy maintenance and timely troubleshooting, thereby minimizing downtime. Furthermore, these models are backed by Kawasaki's extensive support network, ensuring users have access to assistance whenever required.

In summary, the Kawasaki K0450, J8472PR, and J8472 exemplify what modern engineering can achieve. With their impressive blend of performance, efficiency, and user-oriented features, they stand as premier choices for anyone seeking reliable, high-quality machinery. Whether for professional applications or personal projects, these models are designed to deliver unparalleled results.
Top Page Image Contents