Kawasaki J8472PR, K0450 manual Battery Charging, Or call

Page 7

BATTERY CHARGING

ELECTRICAL HAZARD

WARNING

•Battery can fall out and injure a child if vehicle tips over. Always use battery retainer.

•PREVENT FIRE

-Never modify the electrical system. Alterations could cause a fire resulting in serious injury and could also ruin the electrical system.

-Use of the wrong type battery or charger could cause a fire or explosion resulting in serious injury.

-Use of Power Wheels® components in products other than Power Wheels® vehicles could cause overheating, fire or explosion.

•The battery must be handled by adults only. The battery is heavy and contains sulfuric acid (electrolyte). Dropping the battery could result in serious injury.

•Never allow children to charge the battery. Battery charging must be done by adults only. A child could be injured by the elec- tricity involved in charging the battery.

•Read the safety instructions on the battery.

•Examine the battery, charger and their connectors for excessive wear or damage each time you charge the battery. If damage or excessive wear is detected, do not use the charger or the battery until you have replaced the worn or damaged part.

CAUTION

Use the charger in dry locations only.

About Thermal Fuses

Your Power Wheels® 12 volt battery is equipped with a built-in thermal fuse. The thermal fuse is a self-resetting safety device which automatically “trips” and shuts down operation of the vehicle if the vehicle is overloaded or the driving conditions too severe. Once

a fuse has "tripped", remove your foot from the pedal and wait approximately 25 seconds before operating the vehicle again. To avoid repeated automatic shut-downs, do not overload the vehicle by exceeding the 65 lb. (29.5 kg) maximum weight capacity or by towing anything behind the vehicle. Avoid severe driving conditions, such as driving up slopes or running into fixed objects, which can cause the wheels to stop spinning while power is still being supplied to the motors and make sure your child stops the vehicle before switching direction.

If a thermal fuse in a battery continually trips under normal driving conditions, please contact your local Power Wheels® Authorized Service Center. For the location of the Authorized Service Center nearest to you, visit us on-line at www.powerwheels.com,

or call 1-800-348-0751.

Important Notes

•Your new battery must be charged for at least 18 hours before you use it in your vehicle for the first time.

•We recommend that you start charging your battery before beginning assembly of your new vehicle.

•The battery must be upright while charging.

•The charger is not a toy.

•Do not short circuit the battery.

•You do not need to remove the battery from your vehicle to recharge it.

•Before charging the battery, examine the battery case for cracks and other damage which may cause sulfuric acid (electrolyte) to leak during the charging process. If damage is detected, do not charge the battery or use it in your vehicle. Battery acid is very corrosive and can cause severe damage to surfaces it contacts.

•Do not charge the battery on a surface (such as a kitchen counter top) which could be damaged by the acid contained inside the battery. Take precautions to protect the surface on which you charge your battery.

•Use only a Power Wheels® 12 volt charger with "12 V" connector (120 VAC, 60 Hz, 28W with an output of 12 VDC, 1200 mA)

to charge your Power Wheels® 12 volt battery.

Adults Note: Regularly examine the charger for damage to the cord, plug, housing or other parts that may result in the risk of fire, electric shock or injury. In the event of any damage, do not use the charger until the damage has been properly repaired. Please call 1-800-348-0751.

•If your battery is old and will not accept a charge, do not leave it in the vehicle. Always remove a dead battery from the vehicle.

7

J8472pr-0920

Page 6 Page 8
Image 7
Page 6 Page 8
Contents With Assembly Instructions For Models J8472 and K0450 Important Information Table of ContentsElectrical Hazard HandlebarSeat Vehicle Steering Column Cap Plate PartsFront Clip Hubcaps Wheel Covers Bushings Rear Axle Volt BatteryFor your convenience, we included extra fasteners Parts Picture Or call Battery ChargingBattery Charger Connector AssemblyRear Axle Cotter Pin Bushing Motor Assembly Wheel RMotor Assembly Rear Axle Assembly Slots UpTurn the vehicle upright Steering Column ConnectorsSteering Column Fit a cotter pin into the hole on the end of the front axle Wheel LWasher Front Axle Bushing Cotter Pin Front AxleLocate the opening under the drive buttons Brush GuardHand Grip Fit both hand grips on the ends of the handlebarSeat Drive Buttons DecorationFor Model J8472 For Model K0450 Seat Drive Buttons Motor Harness Connector Battery InstallationSeat Battery Retainer Power WheelsCare Battery Care and DisposalAlways sit on the seat Always wear shoes Safe Driving RulesTo disconnect the motor harness Reverse Vehicle OperationDrive Press the Drive button on the tankVehicle Care Charge IndicatorButton Problem Possible Cause Solution Problems and SolutionsShort run time Less than Undercharged battery Operation of the drive system by raising the rear wheels off Bumper-to-Bumper Limited Warranty Limited WarrantyBefore first-time use You must charge the battery Hours

J8472, J8472PR, K0450 specifications

The Kawasaki K0450, J8472PR, and J8472 are characterized by advanced engineering and impressive technological features aimed at optimizing performance and enhancing user experience. These models are backed by Kawasaki’s commitment to innovation and reliability, making them a standout choice in their respective categories.

The Kawasaki K0450 is a powerhouse that offers a combination of robust performance and fuel efficiency. It is equipped with a cutting-edge, high-torque engine designed for optimal power delivery, making it suitable for a variety of applications, from landscaping to construction tasks. The K0450’s compact design ensures ease of maneuverability, while its durable construction promises longevity, even under heavy use in challenging environments.

The J8472PR model, on the other hand, is known for its innovative technology that emphasizes precision and efficiency. It features an advanced control system that allows users to tailor performance settings according to specific needs. This model comes with eco-friendly technology, significantly reducing emissions without compromising power. Additionally, the ergonomic design ensures user comfort, reducing fatigue during extended use.

With the J8472 model, Kawasaki continues its tradition of excellence by integrating modern features that enhance productivity. Notable characteristics include its high-grade materials that ensure longevity and resilience, as well as a user-friendly interface that simplifies operation. Its cutting-edge safety features provide assurance to users, making it a reliable choice in demanding conditions.

All three models showcase Kawasaki's dedication to quality and technological advancement. The incorporation of advanced diagnostics systems allows for easy maintenance and timely troubleshooting, thereby minimizing downtime. Furthermore, these models are backed by Kawasaki's extensive support network, ensuring users have access to assistance whenever required.

In summary, the Kawasaki K0450, J8472PR, and J8472 exemplify what modern engineering can achieve. With their impressive blend of performance, efficiency, and user-oriented features, they stand as premier choices for anyone seeking reliable, high-quality machinery. Whether for professional applications or personal projects, these models are designed to deliver unparalleled results.
Top Page Image Contents