Locke RS-5100 manual Indexing The Ratchet Wheel, RPM Setting, Engaging Traverse

Page 18

RPM Setting

Figure 3-11

13. Start the wheel head.

16.Start the coolant pump, using only a “trickle” of coolant for spin grinding.

17.Begin the spin grinding operation. Grind the reel until the leading edge has a square and sharp edge. For best results, infeed the wheel at 0.001” (one tooth per stroke). See the following instructions to set the auto infeed indexing ratchet wheel.

Indexing The Ratchet Wheel

The ratchet wheel, located just behind the hand wheel, is used to automatically index the amount of “in-feed” of the wheel head. Figure 3-12

CAUTION

PROLONGED CONTACT BETWEEN THE STONE AND REEL MAY CAUSE THE STONE TO CHIP OR BREAK APART, CAUSING SERIOUS INJURY TO THE OPERATOR. DAMAGE TO THE REEL MAY ALSO RESULT.

14.With the carriage in the center of the reel, care- fully adjust wheel head “in” toward reel until slight contact is made. Manually move grinding car- riage left and right. If excessive vibrations or loud grinding sounds occur, quickly adjust wheel head “out,” away from the reel or press the “master kill” button. Check mounting brackets, reel bearings, etc., to make sure all are secure.

NOTE

Sometimes reels wear in either a concave or convex fashion. If the grinding wheel makes contact with the reel only in the center it indicates convex wear. Set limit stops so wheel head travels just beyond points of contact. Read through the following steps, then grind reel until contact is make throughout wheel head’s range of travel. Repeat step 15. If no contact is made beyond points just ground, move limit stops out slightly and regrind. Continue this procedure until contact is make throughout entire length of reel. If wear is concave, reel will have to be ground at each end. Set limit stops as indicated by step 6 and grind until contact is make throughout entire length of reel.

15.If the results of step 14 are satisfactory, engage and start traverse.

Engaging Traverse

5100 Series—Traverse engage lever is located on the left side of the carriage plate. Move it to the cen- ter position.

Ratchet Wheel

Figure 3-12

The amount of “in-feed” per traverse cycle is set by adjusting the screw on the center limit stop. One, two or three teeth can be indexed, infeeding the grinding wheel 0.001, 0.002 or 0.003 inch per traverse cycle respectively.

IMPORTANT

For reels, only 0.001 inch per traverse cycle is recommended by the manufacturer.

NOTE

The distance of travel will vary slightly with the speed of travel. The carriage will “overrun” the return stop if the speed is in- creased without readjusting the screw.

16

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Page Page Page Page Reel and Bedknife Sharpener Introduction Serial NumberSafety Notations SafetyImportant Safety Information Safety RulesMaintenance Safety DecalsPersonal Safety Equipment Child Labor Under 16 Years Old This Act SeeksLocating The Grinder Assembly Instructions and SET-UPUncrating the Sharpener Securing the SharpenerPage Wiring The 5100 Sharpener Electrical Wiring Source To Front Panel Models -220 VoltsCoolant Changing Wheel heads Spin Grinding Refer to -2Micro Switch Turned to the Left Micro Switch Turned to the RightRefer to -6 Wobble Extensions Spin Motor BracketsShaft Being Reversed Ratchet Wheel RPM SettingIndexing The Ratchet Wheel Engaging TraverseManual Relief Grinding Ratchet PawlFinger Guide Thumb Bolt GuardGrinding Relief Angles on Reels Grinding the AnglesBrackets Grinding Angle Adjustment Found with Angle FinderSharpening Bedknives Bedknife Secured with L BracketsPage Grinding Relief Angles on Bedknives Bedknife/Reel Relief AngleGrinding Angle Adjustment Refer to -29Maintenance & Lubrication Clean-UpServicing the Stones Dressing the StoneBelt Tension Troubleshooting Problem Possible Cause SolutionWhy is there a variable speed drive? Why does the sharpener have safety shields?Why does the sharpener have the water/coolant mix? Why is the sharpener built so heavy?Safety Decals Hazardous VoltageAmerican MetricLocke Turf

RS-5100 specifications

The Locke RS-5100 is an innovative security solution designed for both commercial and residential applications, blending advanced technology with user-friendly features. With a sleek design, the RS-5100 is not only aesthetically pleasing but also highly functional, making it a popular choice among property owners looking to enhance their security measures.

One of the standout features of the RS-5100 is its integration of biometric technology. The device supports fingerprint recognition, allowing for quick and secure access. This feature eliminates the need for traditional keys, which can be lost or stolen, providing an added layer of security. Additionally, it can store multiple fingerprints, making it suitable for families or businesses where multiple users require access.

The Locke RS-5100 also incorporates a robust keypad with backlighting for ease of use in low-light conditions. Users can set custom PIN codes, offering an alternative access method. The keypad can be programmed for temporary codes, ideal for contractors or guests needing short-term access without compromising security.

Connectivity is another advantage of the RS-5100. Equipped with Bluetooth technology, users can control and monitor the lock via a smartphone app. This functionality enables remote locking and unlocking, real-time notifications, and activity tracking directly from a mobile device. Such connectivity is particularly useful for property managers overseeing multiple locations.

In terms of build quality, the RS-5100 features a durable construction designed to withstand harsh weather conditions. Its weather-resistant design ensures reliability and longevity, making it an excellent choice for external doors. The lock also boasts a tamper alert system, providing users with instant notifications if any unauthorized attempts are made to access the lock.

Battery life is crucial for any electronic locking system, and the Locke RS-5100 excels in this aspect as well. With an energy-efficient design, the lock can last for months on a single set of batteries, and it features a low-battery alert system to ensure users are never caught off-guard.

Overall, the Locke RS-5100 is a comprehensive security solution that harmonizes advanced technologies such as biometrics, Bluetooth connectivity, and robust construction. Its intuitive features make it a leader in securing entry points while providing convenience and peace of mind for users. Whether it's protecting a family home or a commercial property, the RS-5100 stands out as a versatile choice for modern security needs.
Top Page Image Contents