Saeco Coffee Makers HD8966 manual Troubleshooting, Machine actions Causes

Page 88

86ENGLISH

TROUBLESHOOTING

This chapter summarizes the most common problems you could encoun- ter with your machine.

If you are unable to solve the problem with the information below, visit www.philips.com/support for a list of frequently asked questions or contact the Philips Saeco hotline in your country.

The contact details can be found in the warranty booklet by-packed sepa- rately or on www.philips.com/support.

Machine actions

Causes

Solutions

The machine does not

The machine is not connected to the

switch on.

electric network.

Connect the machine to the electric network.

The power button is on position "0". Check that the power button is set to "I".

The drip tray gets filled al- though no water is drained.

Sometimes water is drained auto- matically by the machine into the drip tray to manage the rinsing of the circuits and ensure optimum machine performance.

This is seen as normal machine behaviour.

Coffee is not hot enough.

The cups/mugs are cold.

Preheat the cups/mugs with hot water or

 

 

use the hot water dispensing spout.

 

 

 

 

The beverage temperature in the

Make sure that the temperature in the

 

programming menu is set on Low.

programming menu is set on Normal or

 

 

High.

 

 

 

 

You added cold milk to the coffee.

Cold milk lowers the temperature of the

 

 

final product. Preheat the milk before

 

 

adding it to the beverage.

 

 

 

No hot water is dispensed.

The hot water/steam dispensing

Clean the hot water dispensing spout.

 

spout is clogged or dirty.

Inspect the steam spout to check that the

 

 

dispensing spout is not clogged. Make

 

 

a hole in the limescale using a pin or a

 

 

needle.

 

 

 

The machine does not fill the cup/mug.

The machine has not been pro- grammed.

Enter the beverage programming menu and adjust the coffee length setting ac- cording to your personal taste for each type of beverage.

Coffee does not have

The blend is unsuitable, coffee is not

Change coffee blend or adjust the grind

enough crema (see note).

freshly roasted or the grind is too

as explained in the “Adjusting the Ceramic

 

coarse.

Coffee Grinder” chapter.

 

 

 

 

The coffee beans or the pre-ground

Make sure that you use fresh coffee beans

 

coffee are too old.

or pre-ground coffee.

 

 

 

Image 88
Contents 02 EN Important Safeguards Instructions for the Power Supply Cord Contents English Safety Instructions English Always put the machine on a fl at and stable surface Compliance with Standards Installation 1c 2 1bGeneral Description Preparing for USE Machine InstallationMachine Packaging Put the lid back on the coffee bean hopper Using the Machine for the First Time Language SelectionAutomatic Rinse/Cleaning Cycle Manual Rinse Cycle Press the buttonInsert Preground Coffee Press OK English Measuring and Programming Water Hardness Coffee Profiles Maintenance Settings Statistics INTENZA+Water Filter Installation Activate FILTER? Place a container under the hot water dispensing spout Replacing the INTENZA+Water Filter Changing Coffee Beans Removing the Coffee Bean HopperInserting the Coffee Bean Hopper English Coffee Emptying Cycle Machine performs a grinding cycle without brewing coffee Profile Selection Coffee Profile AdjustmentsEnabling a New Profile Disabling a User Profile Arabica User Enable Profile Disable Profile Adjusting the Ceramic Coffee Grinder Saeco Adapting SystemAdjusting the Aroma Coffee Strength Adjusting the Dispensing Spout Adjusting the Coffee Quantity Coffee Brewing Using Coffee Beans Brewing CoffeeCoffee Brewing Using Pre-Ground Coffee Press the button to enter the aroma selection menuInsert Preground Coffe Press OK Milk Carafe Filling the Milk CarafeInserting the Milk Carafe Removing the Milk CarafeEmptying the Milk Carafe Brewing MILK-BASED Beverages Cappuccino Insert the Carafe With the Spout Open Cappuccino Adjusting the Milk-Based Product Length English Special Beverages Hot WaterEnglish Adjusting the Hot Water Dispensing Special Beverages Menu for Brewing Other Beverages HOT Water Ristretto Espresso Mild Espresso Intense Memo Beverage Programming Aroma TemperatureCoffee Quantity Taste Milk QuantityHOT Water Programming Water QuantityRestoring Beverage Parameters To confirmMachine Programming ButtonLanguage Settings Stand-by SettingsFactory Settings StatisticsBrew Group Cleaning Cycle MaintenanceDescaling Cleaning of the Carafe Coffee Circuit CleaningCleaning and Maintenance Daily Cleaning of the MachineEnglish Daily Cleaning of the Water Tank Daily Cleaning of the Milk CarafeEnglish Frothed Milk Insert the Carafe With the Spout Open Weekly Cleaning of the Machine Weekly Cleaning of the Milk CarafeEnglish Weekly Cleaning of the Brew Group Do not use detergent or soap to clean the brew group English Monthly Cleaning of the Milk Carafe Start Carafe WASHING? Never drink the solution dispensed during this step Fill Carafe With Fresh Water Monthly Lubrication of the Brew Group Monthly Cleaning of the Brew Group with Coffee Oil Remover Press the button to select Maintenance Press to confirm Place a Container Under Dispensing Spout English Descaling Empty the drip tray internal / external Press the button Pause English Displayed message Meaning of the message Display MessagesSpout open Troubleshooting Machine actions CausesMachine actions Causes Solutions Been shifted Energy Saving Stand-byDisposal Technical Specifications Warranty and ServiceWarranty ServiceOrdering Maintenance Products Machine Accessories 02 IT
Related manuals
Manual 96 pages 1.6 Kb