Kenmore 795.7900 GLIDE-OUT Drawer Basket on some models, Tilting Door on some models, How to use

Page 30

GLIDE-OUT DRAWER BASKET (on some models)

1.To remove, lift basket up and pull out straight out.

2.To Install, pull both rails out to full extension.

Hook the basket supports into the rail tabs and push to

	the back of compartment.	[] WARNING:To avoid hand injury, keep your hands away
	the back of compartment.	from tilting device when drawer is open.
		from tilting device when drawer is open.

TILTING DOOR (on some models)

The tilting door provides easy access to stored foods.

How to use:

Tilt the door down and pull it out.

[] WARNING: Be careful when you open tilting door so that you do not injure your foot!

WIRE DURABASE (on some models)

1.To remove wire Durabase, pull it out to full extension.

Tilt up the front of the wire Durabase and pull it straight out.

2.To install, insert the wire Durabase into frame rails and push back into place.

\\\\\\\\\\\\\\

FREEZER SHELF (on some models)

To remove shelf, grasp it at the front and pull it towards you.

To replace the shelf, simply push it back into place.

Image 30

Contents = color number English Version Spanish French One Year Limited Warranty Disclaimer of implied warranties limitation of remediesMaster Protection Agreements Page USE of Extension Cords Before YOU Throw Away Your OLD Refrigerator Or FreezerRecommended Grounding Method Electrical Shock HazardFreezer Drawer Model ODurabaseFreezer Swing Door Model Unpacking Your Refrigerator InstallationTo Install Base Grille Base Grille InstructionsHOW to Remove Refrigerator Door HOW to Remove Pull OUT DrawerFor Freezer Drawer Models Ta es Top Replacing Refrigerator DoorHOW to Install Pull OUT Drawer Ipprts Lower door into final position and tighten the screwsREMOVING,REVERSING and Replacing Refrigerator Doors For Freezer Drawer ModelsFlat-head screwdriver for prying Pin HOW to Reverse Door Handle HOW to Replace Refrigerator Freezer Doors For Freezer Swing ModelsRefrigerator Doors For Freezer Swing Models 10mm or 13/32-inch socket wrenchNo Phillips head screwdriver 4inch socket wrench Pin Insert Bracket After Door Alignment After Completing the JOBLeveling and Door Closing Instructions below to align the doorsEnsuring Proper AIR Circulation Identify your control typeAdjusting Control Settings RefrigeratorFood Storage Guide Storing Frozen FoodTo remove a sliding shelf from its metal frame Refrigerator ShelvesSliding Out Shelves optional on some models Convenience Shelves optional on some modelsOn some models Refrigerator FeaturesPantry Crisper Humidity Control on some modelsTo remove the glass Crisper Cover with Lattice on InnerSurface on some models To remove the crisper coverDoor Racks Door BinsDurabase on some models Dairy BINEGG BOX on some models Durabase Divider on some modelsGLIDE-OUT Drawer Basket on some models Wire Durabase on some modelsHow to use Tilting Door on some modelsOutside General Cleaning TipsLight Bulb Replacement Door Liners and GasketsPower Interruptions To change the freezer lightIf you choose to leave the refrigerator on while you Normal Sounds YOU MAY Hear When YOU should SET the Icemaker Power Switch to O OFFIcemaker Preparing for VacationPower drill Before YOU BeginFasten the Shut OFF Valve Installation Instructions Choose the Valve LocationDrill the Hole for the Valve Tighten the Pipe ClampPlug in the Refrigerator Connect the Tubing to the RefrigeratorTurn the Water on AT the Shut OFF Valve Start the IcemakerCheck if Refrigerator does not OperateVibration or Rattling Noise ThenFrost or ICE Crystals on Frozen Food Compressor Motor Seems to RUN TOO MuchDoors will not Close Completely Check if ThenRefrigerator Seems to Make TOO Much Noise Cubes Produced by Icemaker are TOO SmallDoors are Difficult to Open Automatic Icemaker does not Work Lights do not WorkIiiiiiiiiiiiiiiiiiiiiiii