Kenmore 795.6827, 795.7900, 795.6900, 795.7827, 795.7809, 795.76200 manual Pin

Page 14

•Remove Washer and set aside.

•Using a 1/4 socket wrench, loosen and remove Hinge Pin from the Middle Hinge Bracket.

Pin

•Use a 10mm or 13/32 inch socket wrench to remove the 2 bolts in Middle Hinge Bracket. Remove 2

screws. Set Middle Hinge Bracket and other parts aside.

•With a fiat-head screwdriver, carefully pry off and remove the cover over the screw holes on the left side

of refrigerator housing.

Fig. 33

•Remove the 2 outer screws from cabinet frame as shown.

You will need these holes for the Middle Hinge Bracket.

F34

•Place screws into outer holes on right side of cabinet. Attach cover on the right side. Cover is force-fitted.

Fig. 35

,_J_

[_ I

•Flip the middle hinge bracket and position on left side of refrigerator and re-attach with two bolts and a 2 phillips screws.

Fig. 36

ge

Bracket

•Attach Middle Hinge Pin and replace washer.

•Put refrigerator door down over the Hinge Pin on the Middle Hinge Pin Bracket.

Middle Hinge Bracket

•Line up Top Hinge with holes in top of refrigerator. Use the 3 bolts to replace the Hinge.

Fig. 38

Top Hinge

Top Hinge

•Tighten Bolts. Force-fit Top Hinge Cover over top Hinge.

Fig. 39

14

Image 14

Contents = color number English Version Spanish French One Year Limited Warranty Disclaimer of implied warranties limitation of remediesMaster Protection Agreements Page USE of Extension Cords Before YOU Throw Away Your OLD Refrigerator Or FreezerRecommended Grounding Method Electrical Shock HazardFreezer Drawer Model ODurabaseFreezer Swing Door Model Unpacking Your Refrigerator InstallationTo Install Base Grille Base Grille InstructionsFor Freezer Drawer Models HOW to Remove Refrigerator DoorHOW to Remove Pull OUT Drawer Ta es Top Replacing Refrigerator DoorHOW to Install Pull OUT Drawer Ipprts Lower door into final position and tighten the screwsFlat-head screwdriver for prying REMOVING,REVERSING and ReplacingRefrigerator Doors For Freezer Drawer Models Pin HOW to Reverse Door Handle HOW to Replace Refrigerator Freezer Doors For Freezer Swing ModelsNo Phillips head screwdriver 4inch socket wrench Refrigerator Doors For Freezer Swing Models10mm or 13/32-inch socket wrench Pin Insert Bracket After Door Alignment After Completing the JOBLeveling and Door Closing Instructions below to align the doorsEnsuring Proper AIR Circulation Identify your control typeAdjusting Control Settings RefrigeratorFood Storage Guide Storing Frozen FoodTo remove a sliding shelf from its metal frame Refrigerator ShelvesSliding Out Shelves optional on some models Convenience Shelves optional on some modelsOn some models Refrigerator FeaturesPantry Crisper Humidity Control on some modelsTo remove the glass Crisper Cover with Lattice on InnerSurface on some models To remove the crisper coverDoor Racks Door BinsDurabase on some models Dairy BINEGG BOX on some models Durabase Divider on some modelsGLIDE-OUT Drawer Basket on some models Wire Durabase on some modelsHow to use Tilting Door on some modelsOutside General Cleaning TipsLight Bulb Replacement Door Liners and GasketsIf you choose to leave the refrigerator on while you Power InterruptionsTo change the freezer light Normal Sounds YOU MAY Hear When YOU should SET the Icemaker Power Switch to O OFFIcemaker Preparing for VacationPower drill Before YOU BeginFasten the Shut OFF Valve Installation Instructions Choose the Valve LocationDrill the Hole for the Valve Tighten the Pipe ClampPlug in the Refrigerator Connect the Tubing to the RefrigeratorTurn the Water on AT the Shut OFF Valve Start the IcemakerCheck if Refrigerator does not OperateVibration or Rattling Noise ThenFrost or ICE Crystals on Frozen Food Compressor Motor Seems to RUN TOO MuchDoors will not Close Completely Check if ThenDoors are Difficult to Open Refrigerator Seems to Make TOO Much NoiseCubes Produced by Icemaker are TOO Small Automatic Icemaker does not Work Lights do not WorkIiiiiiiiiiiiiiiiiiiiiiii