Level Control Adjustment, Troubleshooting

TRS 1/4” phone plug or the XLR plug will provide superior interference rejection and performance. Sometimes, with difficult interference problems, it will be helpful to lift the shield ground on a balanced cable at the PV®215D end. Check any input changes carefully, always turning the volume control down before plugging and unplugging cables or making grounding changes.

Use of high quality, premium cables is recommended for the PV®215D, as these usually have better shielding and materials and will provide greater long-term reliability. It is usually a good idea to leave some slack at the input to the PV®215D and also to tape the cables down or run them under a cable guard to avoid anyone tripping over them or pulling the PV®215D over.

Level Control Adjustment

The PV®215D is equipped with a level control (5) to facilitate use in many different applications. With the level control adjusted fully clockwise, gain is at maximum and the input sensitivity is 0.650 V RMS for full-rated output. When driving the PV®215D from a mixer, it may be advantageous to reduce the input sensitivity by turning the level control to the halfway point or even less. The PV®215D will now more closely match the sensitivity of a typical power amp.

If the mixing board indicates clipping of its output signals, then all of the PV®215D power capability is not being utilized cleanly. Clipping the signal before it gets to the PV®215D is not optimal. Reduce the mixer output level and turn up the level control on the PV®215D.

The amplifier in the PV®215D is equipped with DDT™ and an LED indicator to show that DDT™ has engaged. If the sound seems heavily compressed, check this indicator; if it is blinking RED more than occasionally, then the drive level from the mixer (or the level control on the PV®215D) needs to be reduced.

When first turning on the sound system, switch on all upstream electronics first, then the PV®215D with its level control fully counterclockwise (all the way down). Begin checking levels with the mixer output level controls all the way down, and bring them up slowly with the PV®215D level control set to the desired setting (one-third of the way up is recommended as a starting point).

Use of the PV®215D with a powered Subwoofer

Powered subwoofers often have a built-in electronic crossover to allow a high-pass filtered signal (lows rolled-off) to be sent to the upper range speaker. The PV®118D Sub is such a subwoofer. When using the PV®215D with this type of powered subwoofer, first run the signal from the mixer or signal source to the powered sub input, then come out of the combo jack labeled “THRU/HPF” and send that signal to the PV®215D input jack. On the PV®118D Sub, the button to the far left labeled THRU/HPF should be pushed in to engage the high-pass filter (HPF). On other powered subwoofers, if they have a similar high-pass filter function, send the signal in and out of the subwoofer according to the Manufacturer’s instructions, which should be similar to the instructions as outlined above.

TROUBLESHOOTING

No Output at All

First, make sure the unit has AC power and is turned ON. Make sure the Power/Clip LED (8) is illuminated Green. If not, make certain the ON/OFF switch (3) is in the ON position and check the IEC power cord connection (2) by ensuring it is fully engaged and seated. Make certain the AC line cord is plugged into a working AC outlet. Finally, check the fuse (2a). (See the Rear Panel: Fuse section for safety instructions.)

Once assured your unit is getting AC power, check that the PV®215D is getting a signal. Temporarily disconnect the cable running to its inputs and connect it to some other device capable of reproducing the signal (i.e., a power amp and speaker). If this produces a signal, make sure that all Volume controls being used have been turned up to a satisfactory level (one-third to halfway).

If the PV®215D has been subjected to direct sunlight or excessive heat, the built-in thermal protection may have been triggered. The power/clip LED will be illuminated RED if this is the case. If so, turn off the PV®215D and let it cool for a sufficient amount of time.

If there is still no output, contact your authorized Peavey® dealer or the Peavey® International Service Center.

Hum or Buzz

If the PV®215D is producing a hum or buzz, this can be AC outlet related. Try plugging the PV®215D into a different AC outlet. Sometimes, if a different AC power circuit (breaker) is used for the mixer and the PV®215D, it can cause hum problems.

PV215D specifications

The Peavey PV215D is a powerful and versatile dual 15-inch loudspeaker system designed to deliver exceptional sound quality for live performances, events, and installations. Renowned for its robust construction and advanced technologies, the PV215D appeals to musicians, sound engineers, and venue owners seeking reliability and performance in one package.

One of the standout features of the PV215D is its dual 15-inch heavy-duty woofer configuration, which is engineered to produce deep, resonant bass and clear mids. This design allows the speaker to handle a wide frequency range, ensuring that every note is delivered with precision and clarity. The inclusion of a high-frequency compression driver ensures the production of crisp highs, further enhancing the speaker's versatility in various sound applications.

At the heart of the PV215D is Peavey's proprietary technology that improves sound dispersion. The speaker features a unique horn design that optimally distributes sound throughout the venue, significantly minimizing dead spots and providing a more uniform listening experience. This technology makes the PV215D ideal for larger spaces, whether in outdoor festivals or indoor concert halls.

Durability is a key consideration for any professional audio gear, and the PV215D does not disappoint. Built with a rugged, plywood enclosure, the speaker is designed to withstand the rigors of touring and frequent transport. Its protective grille ensures that the drivers are shielded from damage without compromising sound quality. Additionally, the speaker’s flight-ready design offers options for mounting and rigging, making it a versatile tool for any audio setup.

Peavey has also equipped the PV215D with built-in power amplification, offering a powerful output to drive the speaker effectively without the need for an external amp. This self-powered feature simplifies setup and reduces the amount of equipment needed for performances.

In terms of connectivity, the PV215D provides multiple input options, allowing for easy integration into a variety of audio systems. It also includes a built-in equalizer, enabling users to tailor the sound to their specific needs and preferences.

Overall, the Peavey PV215D is a comprehensive solution for high-quality sound reinforcement. Offering impressive power, durability, and sonic versatility, it stands out in the competitive market of professional audio equipment. Whether for live music, DJ events, or public speaking engagements, the PV215D is designed to meet the demands of both performers and audiences, ensuring an unforgettable auditory experience.