Murray 425604x18A manual HOW to Install the Seat, HOW to Assemble the Steering Wheel

Page 11

ASSEMBLY

HOW TO INSTALL THE SEAT

Use the fasteners shown below to install the seat. The fasteners are shown at full size.

1.Carefully remove the plastic bag from the seat.

2.Align the holes in the seat

hinge to the holes in the

(A)

seat

(Figure 1). Fasten

1001054

the seat to the seat hinge

 

with

the fasteners as

 

 

shown.

 

3.Check the operating posi- tion of the seat. If the seat needs to be adjusted,

loosen the two wing

 

bolts. Slide the seat for-

 

ward or backward along

(B)

the seat adjusting holes

17x47

as shown. Tighten the

 

wing bolts (A).

 

Seat

 

Seat Hinge

Seat

 

Adjusting

Hole

B

A

 

Figure 1

HOW TO ASSEMBLE THE STEERING WHEEL

Use the fasteners shown below to install the steering wheel. The fasteners are shown at full size.

(A)

(C)

25x3

17x146

1.Make sure the front wheels point forward.

2.Slide the cover, if equipped, over the steering post (Figure 2).

NOTE: The cover is an optional accessory and is not re- quired on all models.

3.Slide the steering wheel onto the steering post.

4.Apply firm pressure to center of the steering wheel with the palm of your hand until you hear a clicking noise. To check for proper locking of the steering wheel to the steering post, pull upward on steering wheel.

5.Use the fasteners shown above to secure the steering wheel. The fasteners are shown at full size. Tighten the screw. DO NOT over tighten.

6.Remove adhesive backing from hub cover (found in parts bag) and place hub cover over hub.

Hub Cover

A

C

Steering Wheel

Cover

Steering Post

Figure 2

 

HOW TO ASSEMBLE THE GAUGE WHEELS

Use the fasteners shown below to install the gauge wheels.

(B)

(A)17x91 31x11

1.Attach the gauge wheels to the axle bolts with the fasteners.

NOTE: The axle bolt is mounted in the LOW position. To change the position to a higher cutting position, see “How To Adjust The Gauge Wheels” in the Maintenance section.

Axle Bolt

B

A

Gauge Wheel

Figure 3

F–030753L

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model Table of Contents Safe Operation Practices for Ride-on Mowers OWNER’S InformationEnvironmental Awareness II. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowControl And Operating Pictorials Safety Warning PictorialsInternational Pictorials International PictorialsAssembly AssemblyHOW to Assemble the Gauge Wheels HOW to Install the SeatHOW to Assemble the Steering Wheel Remove the battery and battery tray Maintenance Free BatteryHOW to Charge Maintenance Free Battery HOW to Install the Battery CablesCheck the Tires HOW to Prepare the EngineCheck the Level of the Mower Housing IMPORTANT! Before YOU Start MowingLocation of Controls OperationAttachments HOW to USE the Throttle ControlTo 2/3 HOW to USE the Speed Control PedalHOW to Disconnect the Transmission To 1/2HOW to Transport the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Stop the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingCarburetor HOW to Start the EngineBefore Starting the Engine Mowing and Bagging Tips Operating TipsGeneral Recommendations MaintenanceFrequency Maintenance Required Comments HOW to Check the MufflerMount the blade and blade adapter on the mandrel HOW to Remove and Install the BladeHOW to Sharpen the Blade Inspect BladeHOW to Adjust the Blade Rotation Control Remove the 1/4 inch 6 mm pin or bolt Figure HOW to Check and Adjust the Motion Drive BeltDisconnect the red cable from the positive + terminal HOW to Check and Adjust the Drive BrakeHOW to Check the Fuel Filter Where to LubricateRemove the mower drive belt from the stack pulley HOW to Remove the Mower HousingHOW to Install the Mower Housing 5,6 HOW to Adjust the Gauge WheelsLift Lever Hole No Position No HOW to Level the Mower Housing Remove the mid-idler pulley HOW to Replace the Motion Drive BeltInstall the mid-idler pulley HOW to Replace the Mower Drive Belt Fasten the rear wheel with washer and e-ring HOW to Install the WheelsBattery HOW to Replace the FuseHOW to Replace the Light Bulb HOW to Clean the Mower HousingTrouble Shooting Chart USA 030753LChassis & Hood Repair PartsKey Description Drive Assembly Drive Assembly Steering Steering Repair Parts Mower Housing Suspension Mower Housing Suspension Mower Housing 7601032 Repair Parts Engine Mount Assembly Engine Mount Assembly Repair Parts Electrical System Key Part Description Electrical System030753L Index Model No Bushel Capacity Model No

425604x18A specifications

The Murray 425604x18A is a powerful and versatile lawn mower engineered to meet the needs of both residential and commercial users. With its robust design and advanced features, this mower stands out in the market, ensuring efficient lawn maintenance for a variety of grass types and terrains.

One of the key features of the Murray 425604x18A is its reliable engine. Powered by a high-performance motor, it delivers consistent power for cutting through tough grass and uneven landscapes. The engine boasts a low-emission system, making it an environmentally friendly option while still maintaining optimal performance. This balance of power and eco-friendliness is particularly appealing to those who are conscious of their carbon footprint.

In terms of cutting capabilities, the Murray 425604x18A offers a cutting width of 18 inches, allowing for easy maneuverability in tighter spaces. It is equipped with multiple cutting height adjustments, enabling users to achieve their desired lawn finish, whether they prefer a closely cropped look or a longer grass finish. The precision cutting technology ensures that each pass leaves a uniform and clean cut, promoting a healthier lawn.

Comfort and ease of use are also highlights of this mower. The ergonomic design includes an adjustable handle, ensuring that operators of all heights can find a comfortable grip. The lightweight construction enhances maneuverability, reducing fatigue during prolonged use. The mower’s large wheels provide excellent traction, making it suitable for various terrains, from hilly landscapes to flat gardens.

Another notable characteristic is the mower's ease of maintenance. The durable blade system is designed for simple sharpening and replacement, allowing users to keep their mower in top condition with minimal hassle. Additionally, the easy-to-access engine compartment simplifies routine checks and servicing.

The Murray 425604x18A is also designed with safety in mind. Features such as a safety switch ensure that the mower cannot be started accidentally, protecting users and bystanders alike.

Overall, the Murray 425604x18A combines power, efficiency, and ease of use, making it an outstanding choice for anyone looking to maintain their lawn effectively. With its thoughtful design and reliable performance, this mower stands ready to tackle the challenges of lawn care with confidence.
Top Page Image Contents