Murray 425604x18A manual HOW to Replace the Fuse, HOW to Replace the Light Bulb, Engine, Battery

Page 33

MAINTENANCE

HOW TO REPLACE THE FUSE

If the fuse is blown, the engine will not start. The location of the fuse is next to the battery. Remove the fuse and replace with a automotive fuse (Figure 38).

Automotive Fuse

Figure 38

HOW TO REPLACE THE LIGHT BULB

1.Raise the tractor hood.

2.Turn the light socket until the tabs on the socket align with the notches in the bezel (Figure 39). Remove the light socket. Turn the light bulb and remove the bulb.

3.Install a new light bulb. Align the light socket with the notches in the bezel and turn the light socket to lock in position.

Bezel

Light Bulb

Light Socket

Figure 39

HOW TO CLEAN THE MOWER HOUSING

WARNING: Before you clean the mower housing, stop the engine and disconnect the wire to the spark plug.

Grass and other debris on top of the mower housing can keep the belt from working correctly. For safety and correct operation, frequently clean the top of the mower housing. Remove grass and debris from around the pulleys and other moving parts.

1.Move the lever for the blade rotation control to the ENGAGE position.

2.Clean the top of the mower housing.

3.Move the lever for the blade rotation control to the DISENGAGE position.

4.Again clean the top of the mower housing.

5.After you cut the grass, clean the bottom of the mower housing.

STORAGE (over 30 days)

At the end of each year, prepare the unit for storage as follows.

THE ENGINE

For storage information, see the the engine manufacturer’s instructions.

THE BATTERY

1.Remove the battery.

2.Clean the battery terminals of any deposits.

3.Charge the battery. See the instructions on “How To Prepare And Charge The Battery”.

4.Store the battery in a cool, dry place.

NOTE: After a long time in storage, charge the battery.

1.Start the engine.

2.Run the engine until the fuel tank and the carburetor are out of fuel and the engine stops.

3.Do not leave fuel in the fuel tank or the carburetor. The fuel can damage the function of the fuel system. Some models have a fuel drain (Figure 40). Hold a cloth under the fuel drain. Push the fuel drain until the carburetor is empty.

4.After storage, make sure you use fresh fuel.

Fuel Drain

Figure 40

THE FUEL SYSTEM

WARNING: Do not drain the gasoline inside a build- ing or near a fire. Do not smoke because the fumes from the fuel can cause an explosion.

CLEAN THE UNIT

1.Clean the dirt and grass from the engine.

2.Clean the mower housing.

LUBRICATE THE UNIT

See the “Lubrication” instructions in this book.

F–030753L

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Model Table of Contents OWNER’S Information Environmental AwarenessSafe Operation Practices for Ride-on Mowers II. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowInternational Pictorials Safety Warning PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Install the Seat HOW to Assemble the Steering WheelHOW to Assemble the Gauge Wheels HOW to Charge Maintenance Free Battery Maintenance Free BatteryHOW to Install the Battery Cables Remove the battery and battery trayCheck the Level of the Mower Housing HOW to Prepare the EngineIMPORTANT! Before YOU Start Mowing Check the TiresLocation of Controls OperationAttachments HOW to USE the Throttle ControlHOW to Disconnect the Transmission HOW to USE the Speed Control PedalTo 1/2 To 2/3HOW to Change the Cutting Height HOW to SET the Parking BrakeHOW to Stop the Unit HOW to Transport the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingHOW to Start the Engine Before Starting the EngineCarburetor Mowing and Bagging Tips Operating TipsFrequency Maintenance Required Comments MaintenanceHOW to Check the Muffler General RecommendationsHOW to Sharpen the Blade HOW to Remove and Install the BladeInspect Blade Mount the blade and blade adapter on the mandrelHOW to Adjust the Blade Rotation Control Remove the 1/4 inch 6 mm pin or bolt Figure HOW to Check and Adjust the Motion Drive BeltDisconnect the red cable from the positive + terminal HOW to Check and Adjust the Drive BrakeHOW to Check the Fuel Filter Where to LubricateHOW to Remove the Mower Housing HOW to Install the Mower HousingRemove the mower drive belt from the stack pulley HOW to Adjust the Gauge Wheels Lift Lever Hole No Position No5,6 HOW to Level the Mower Housing HOW to Replace the Motion Drive Belt Install the mid-idler pulleyRemove the mid-idler pulley HOW to Replace the Mower Drive Belt Fasten the rear wheel with washer and e-ring HOW to Install the WheelsHOW to Replace the Light Bulb HOW to Replace the FuseHOW to Clean the Mower Housing BatteryTrouble Shooting Chart USA 030753LChassis & Hood Repair PartsKey Description Drive Assembly Drive Assembly Steering Steering Repair Parts Mower Housing Suspension Mower Housing Suspension Mower Housing 7601032 Repair Parts Engine Mount Assembly Engine Mount Assembly Repair Parts Electrical System Key Part Description Electrical System030753L Index Model No Bushel Capacity Model No

425604x18A specifications

The Murray 425604x18A is a powerful and versatile lawn mower engineered to meet the needs of both residential and commercial users. With its robust design and advanced features, this mower stands out in the market, ensuring efficient lawn maintenance for a variety of grass types and terrains.

One of the key features of the Murray 425604x18A is its reliable engine. Powered by a high-performance motor, it delivers consistent power for cutting through tough grass and uneven landscapes. The engine boasts a low-emission system, making it an environmentally friendly option while still maintaining optimal performance. This balance of power and eco-friendliness is particularly appealing to those who are conscious of their carbon footprint.

In terms of cutting capabilities, the Murray 425604x18A offers a cutting width of 18 inches, allowing for easy maneuverability in tighter spaces. It is equipped with multiple cutting height adjustments, enabling users to achieve their desired lawn finish, whether they prefer a closely cropped look or a longer grass finish. The precision cutting technology ensures that each pass leaves a uniform and clean cut, promoting a healthier lawn.

Comfort and ease of use are also highlights of this mower. The ergonomic design includes an adjustable handle, ensuring that operators of all heights can find a comfortable grip. The lightweight construction enhances maneuverability, reducing fatigue during prolonged use. The mower’s large wheels provide excellent traction, making it suitable for various terrains, from hilly landscapes to flat gardens.

Another notable characteristic is the mower's ease of maintenance. The durable blade system is designed for simple sharpening and replacement, allowing users to keep their mower in top condition with minimal hassle. Additionally, the easy-to-access engine compartment simplifies routine checks and servicing.

The Murray 425604x18A is also designed with safety in mind. Features such as a safety switch ensure that the mower cannot be started accidentally, protecting users and bystanders alike.

Overall, the Murray 425604x18A combines power, efficiency, and ease of use, making it an outstanding choice for anyone looking to maintain their lawn effectively. With its thoughtful design and reliable performance, this mower stands ready to tackle the challenges of lawn care with confidence.
Top Page Image Contents