Murray 425604x18A manual HOW to Adjust the Blade Rotation Control

Page 23

MAINTENANCE

HOW TO ADJUST THE BLADE ROTATION CONTROL

WARNING: To prevent an injury, the blade rotation control must operate correctly.

In normal usage, the blade rotation control will not require an adjustment. However, if the cutting performance decreases or the quality of cut is poor, make the following changes.

1.When you mow, make sure the throttle control in in the FAST position.

2.Move the blade rotation control to the DISENGAGE position (Figure 15).

3.Stop the engine. Disconnect the wire from the spark plug.

Disengage

Position

Blade Rotation Control

Engage Position

Figure 15

4.Check the blade(s). Keep a sharp edge on the blade(s). A blade that is not sharp will cause the tips of the grass to become brown.

5.Disconnect the blade drive spring from the blade control rod. Move the blade drive spring to the middle hole (Figure 16). This will increase the tension on the mower drive belt.

DISENGAGE POSITION

Blade

 

Top Hole (New Belt)

 

 

Control Rod

 

Middle Hole

 

 

Bottom Hole

 

Blade Drive Spring

Figure 16

 

 

6.Attach the wire to the spark plug. Mow for a short distance and again check the quality of cut. If necessary, move the blade drive spring to the bottom hole.

7.Again check the quality of cut. If the quality of cut has not im- proved, replace the mower drive belt. See “How To Replace The Mower Drive Belt”. If replacing the belt does not correct the problem, take the unit to an authorized service center.

8.Move the blade rotation control to the DISENGAGE posi- tion. Stop the engine. Disconnect the wire from the spark plug. Check the operation of the blade brake. Rotate the pulleys with your hand. Make sure the brake pads are pressed tightly against the pulleys (Figure 17).

WARNING: If the brake pads do not press tightly against the pulleys, take the unit to an authorized service center.

Blade Brake

Brake Pad

Against Pulley

Figure 17

9.Move the blade rotation control to the ENGAGE position. Check the pads for the blade brake. If the pads are excessively worn or damaged, replace the brake pad assemblies. Correct replacement parts and assistance are available from an autho- rized service center.

10.Attach the wire to the spark plug. Mow for a short distance and again check the operation of the blade rotation control.

11.When you move the blade rotation control to the DISENGAGE position, all movement will stop within five se- conds. If there is movement of the belt or the blades continue to rotate, engage and disengage the blade rotation control five times to remove any excess rubber from a new mower drive belt. If you need assistance, take the unit to an autho- rized service center.

12.If you replace the mower drive belt, move the blade drive spring to the top hole (Figure 16).

F–030753L

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model Table of Contents Safe Operation Practices for Ride-on Mowers OWNER’S InformationEnvironmental Awareness II. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowControl And Operating Pictorials Safety Warning PictorialsInternational Pictorials International PictorialsAssembly AssemblyHOW to Assemble the Gauge Wheels HOW to Install the SeatHOW to Assemble the Steering Wheel Remove the battery and battery tray Maintenance Free BatteryHOW to Charge Maintenance Free Battery HOW to Install the Battery CablesCheck the Tires HOW to Prepare the EngineCheck the Level of the Mower Housing IMPORTANT! Before YOU Start MowingLocation of Controls OperationAttachments HOW to USE the Throttle ControlTo 2/3 HOW to USE the Speed Control PedalHOW to Disconnect the Transmission To 1/2HOW to Transport the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Stop the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingCarburetor HOW to Start the EngineBefore Starting the Engine Mowing and Bagging Tips Operating TipsGeneral Recommendations MaintenanceFrequency Maintenance Required Comments HOW to Check the MufflerMount the blade and blade adapter on the mandrel HOW to Remove and Install the BladeHOW to Sharpen the Blade Inspect BladeHOW to Adjust the Blade Rotation Control Remove the 1/4 inch 6 mm pin or bolt Figure HOW to Check and Adjust the Motion Drive BeltDisconnect the red cable from the positive + terminal HOW to Check and Adjust the Drive BrakeHOW to Check the Fuel Filter Where to LubricateRemove the mower drive belt from the stack pulley HOW to Remove the Mower HousingHOW to Install the Mower Housing 5,6 HOW to Adjust the Gauge WheelsLift Lever Hole No Position No HOW to Level the Mower Housing Remove the mid-idler pulley HOW to Replace the Motion Drive BeltInstall the mid-idler pulley HOW to Replace the Mower Drive Belt Fasten the rear wheel with washer and e-ring HOW to Install the WheelsBattery HOW to Replace the FuseHOW to Replace the Light Bulb HOW to Clean the Mower HousingTrouble Shooting Chart USA 030753LChassis & Hood Repair PartsKey Description Drive Assembly Drive Assembly Steering Steering Repair Parts Mower Housing Suspension Mower Housing Suspension Mower Housing 7601032 Repair Parts Engine Mount Assembly Engine Mount Assembly Repair Parts Electrical System Key Part Description Electrical System030753L Index Model No Bushel Capacity Model No

425604x18A specifications

The Murray 425604x18A is a powerful and versatile lawn mower engineered to meet the needs of both residential and commercial users. With its robust design and advanced features, this mower stands out in the market, ensuring efficient lawn maintenance for a variety of grass types and terrains.

One of the key features of the Murray 425604x18A is its reliable engine. Powered by a high-performance motor, it delivers consistent power for cutting through tough grass and uneven landscapes. The engine boasts a low-emission system, making it an environmentally friendly option while still maintaining optimal performance. This balance of power and eco-friendliness is particularly appealing to those who are conscious of their carbon footprint.

In terms of cutting capabilities, the Murray 425604x18A offers a cutting width of 18 inches, allowing for easy maneuverability in tighter spaces. It is equipped with multiple cutting height adjustments, enabling users to achieve their desired lawn finish, whether they prefer a closely cropped look or a longer grass finish. The precision cutting technology ensures that each pass leaves a uniform and clean cut, promoting a healthier lawn.

Comfort and ease of use are also highlights of this mower. The ergonomic design includes an adjustable handle, ensuring that operators of all heights can find a comfortable grip. The lightweight construction enhances maneuverability, reducing fatigue during prolonged use. The mower’s large wheels provide excellent traction, making it suitable for various terrains, from hilly landscapes to flat gardens.

Another notable characteristic is the mower's ease of maintenance. The durable blade system is designed for simple sharpening and replacement, allowing users to keep their mower in top condition with minimal hassle. Additionally, the easy-to-access engine compartment simplifies routine checks and servicing.

The Murray 425604x18A is also designed with safety in mind. Features such as a safety switch ensure that the mower cannot be started accidentally, protecting users and bystanders alike.

Overall, the Murray 425604x18A combines power, efficiency, and ease of use, making it an outstanding choice for anyone looking to maintain their lawn effectively. With its thoughtful design and reliable performance, this mower stands ready to tackle the challenges of lawn care with confidence.
Top Page Image Contents