Murray 425604x18A manual HOW to Remove the Mower Housing, HOW to Install the Mower Housing

Page 27

MAINTENANCE

HOW TO REMOVE THE MOWER HOUSING

1.Move the blade rotation control to the DISENGAGE position.

2.If equipped, remove the gauge wheels.

3.Move the lift lever to the level

adjustment position(Figure 24).

WARNING: The lift lever is spring loaded. Make sure the lift lever is locked in the LEVEL ADJUST- MENT position.

4. Remove the hair pins and the

 

 

washers from the adjuster

 

 

arms (Figure 25). See illustra-

Level Adjustment

 

tions “C” and “D”.

 

Position

Figure 24

 

5.Remove the hair pins and washers from the suspension links. See illustrations “A” and “B”.

6.Disconnect the extension spring from the blade control rod. See illustration “E”.

7.Disconnect the front hanger from the axle support. See illustration “F”.

8.Remove the mower drive belt from the stack pulley.

9.Pull the mower housing away from the right side of the unit.

10.To operate without the mower housing, move the lift lever to the TOP position.

HOW TO INSTALL THE MOWER HOUSING

1.Push the mower housing under the right side of the unit.

2.Put the mower drive belt around the stack pulley. Make sure the “V” side of the mower drive belt is against the stack pulley. Also, make sure the mower drive belt is not twisted.

3.Attach the front hanger to the axle support with the hanger rod. Fasten with the fasteners as shown. See illustration “F”.

4.Make sure the mower drive belt is between the stack pulley and the two belt guides. See illustration “G”.

5.Attach the suspension links to the lifter assembly. Fasten with the washers and hair pins. See illustrations “A” and “B”.

6.Attach the right and the left adjuster arms to the suspension brackets. Fasten with the washers and hair pins. See illustra- tions “C” and “D”.

7.Attach the extension spring to the blade control rod. See illustration “E”.

8.Move the blade rotation control to the ENGAGE position. Make sure the mower drive belt is inside all the belt guides.

9.Make sure the mower housing is level. See the instructions on “How To Level The Mower Housing”.

10.If equipped, install the gauge wheels.

11.Check the operation of the blade rotation control. See the in- structions on “How To Adjust The Blade Rotation Control”.

A

 

Lift Lever

 

 

 

 

 

Suspension

Stack Pulley

 

 

Link

Blade Rotation

 

 

 

 

 

 

Control

 

B

 

Belt

Belt

 

 

 

 

Guide

 

 

Guide

 

 

 

 

 

Mower Drive Belt

Suspension

A

 

 

Link

Lifter

 

Adjuster

 

 

Arm

 

Assembly

 

 

 

 

 

B

 

A

 

 

 

 

 

 

B

 

 

 

Blade

 

Adjuster

 

Control Rod

 

Arm

Hanger Rod

 

 

 

 

 

 

Extension

 

 

 

Spring

 

A

 

 

 

B

 

 

 

 

 

Front Hanger

 

 

Gauge Wheel

Mower Drive Belt

Figure 25

 

 

F–030753L

 

27

 

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Model Table of Contents OWNER’S Information Environmental AwarenessSafe Operation Practices for Ride-on Mowers II. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowControl And Operating Pictorials Safety Warning PictorialsInternational Pictorials International PictorialsAssembly AssemblyHOW to Install the Seat HOW to Assemble the Steering WheelHOW to Assemble the Gauge Wheels Remove the battery and battery tray Maintenance Free BatteryHOW to Charge Maintenance Free Battery HOW to Install the Battery CablesCheck the Tires HOW to Prepare the EngineCheck the Level of the Mower Housing IMPORTANT! Before YOU Start MowingLocation of Controls OperationAttachments HOW to USE the Throttle ControlTo 2/3 HOW to USE the Speed Control PedalHOW to Disconnect the Transmission To 1/2HOW to Transport the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Stop the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingHOW to Start the Engine Before Starting the EngineCarburetor Mowing and Bagging Tips Operating TipsGeneral Recommendations MaintenanceFrequency Maintenance Required Comments HOW to Check the MufflerMount the blade and blade adapter on the mandrel HOW to Remove and Install the BladeHOW to Sharpen the Blade Inspect BladeHOW to Adjust the Blade Rotation Control Remove the 1/4 inch 6 mm pin or bolt Figure HOW to Check and Adjust the Motion Drive BeltDisconnect the red cable from the positive + terminal HOW to Check and Adjust the Drive BrakeHOW to Check the Fuel Filter Where to LubricateHOW to Remove the Mower Housing HOW to Install the Mower HousingRemove the mower drive belt from the stack pulley HOW to Adjust the Gauge Wheels Lift Lever Hole No Position No5,6 HOW to Level the Mower Housing HOW to Replace the Motion Drive Belt Install the mid-idler pulleyRemove the mid-idler pulley HOW to Replace the Mower Drive Belt Fasten the rear wheel with washer and e-ring HOW to Install the WheelsBattery HOW to Replace the FuseHOW to Replace the Light Bulb HOW to Clean the Mower HousingTrouble Shooting Chart USA 030753LChassis & Hood Repair PartsKey Description Drive Assembly Drive Assembly Steering Steering Repair Parts Mower Housing Suspension Mower Housing Suspension Mower Housing 7601032 Repair Parts Engine Mount Assembly Engine Mount Assembly Repair Parts Electrical System Key Part Description Electrical System030753L Index Model No Bushel Capacity Model No

425604x18A specifications

The Murray 425604x18A is a powerful and versatile lawn mower engineered to meet the needs of both residential and commercial users. With its robust design and advanced features, this mower stands out in the market, ensuring efficient lawn maintenance for a variety of grass types and terrains.

One of the key features of the Murray 425604x18A is its reliable engine. Powered by a high-performance motor, it delivers consistent power for cutting through tough grass and uneven landscapes. The engine boasts a low-emission system, making it an environmentally friendly option while still maintaining optimal performance. This balance of power and eco-friendliness is particularly appealing to those who are conscious of their carbon footprint.

In terms of cutting capabilities, the Murray 425604x18A offers a cutting width of 18 inches, allowing for easy maneuverability in tighter spaces. It is equipped with multiple cutting height adjustments, enabling users to achieve their desired lawn finish, whether they prefer a closely cropped look or a longer grass finish. The precision cutting technology ensures that each pass leaves a uniform and clean cut, promoting a healthier lawn.

Comfort and ease of use are also highlights of this mower. The ergonomic design includes an adjustable handle, ensuring that operators of all heights can find a comfortable grip. The lightweight construction enhances maneuverability, reducing fatigue during prolonged use. The mower’s large wheels provide excellent traction, making it suitable for various terrains, from hilly landscapes to flat gardens.

Another notable characteristic is the mower's ease of maintenance. The durable blade system is designed for simple sharpening and replacement, allowing users to keep their mower in top condition with minimal hassle. Additionally, the easy-to-access engine compartment simplifies routine checks and servicing.

The Murray 425604x18A is also designed with safety in mind. Features such as a safety switch ensure that the mower cannot be started accidentally, protecting users and bystanders alike.

Overall, the Murray 425604x18A combines power, efficiency, and ease of use, making it an outstanding choice for anyone looking to maintain their lawn effectively. With its thoughtful design and reliable performance, this mower stands ready to tackle the challenges of lawn care with confidence.
Top Page Image Contents