Murray 387002x92D IMPORTANT! Before YOU Start Mowing, HOW to Prepare the Engine, Check the Tires

Page 13

ASSEMBLY

IMPORTANT! BEFORE YOU START MOWING

-Check the engine oil.

-Fill the fuel tank with gasoline.

-Check the air pressure of the tires.

-Check the level of the mower housing.

-Make sure the battery cables are attached.

-Make sure the wire is attached to the spark plug.

WARNING: Before doing any assembly or mainte- nance to the mower, remove the wire from the spark plug.

NOTE: In this instruction book, left and right describe the location of a part with the operator on the seat.

HOW TO PREPARE THE ENGINE

NOTE: The engine was shipped from the factory filled with oil. Check the level of the oil. Add oil as needed.

NOTE: The operation of a new engine will sometimes result in a slight amount of smoke. This smoke is caused by paint or oil on or around the muffler. This is normal and only expected during initial operation.

A separate engine manual is also included with the unit. See this engine manual for the manufacturer’s instructions for the type of gasoline and oil to use. Before you use the unit, read the information on safety, operation, maintenance, and storage.

WARNING: Follow the engine manufacturer’s instructions for the type of gasoline and oil to use. Always use a safety gasoline container. Do not smoke when adding gasoline to the engine. When inside an enclosure, do not fill with gasoline. Before you add gasoline, stop the engine. Let the engine cool for several minutes.

IMPORTANT: This unit is equipped with an internal combustion engine and must not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it must be maintained in effective working order by the operator.

In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. See an Authorized Service Center for a spark arrester for the muffler.

In some areas, local law requires the use of a resistor spark plug to control the ignition signals. See an Authorized Service Center for a resistor spark plug for the engine.

NOTE: Actual sustained horsepower will likely be lower due to operating limitations and environmental factors.

CHECK THE TIRES

NOTE: The tires were over inflated for shipment. The correct air pressure is shown on the side of the tire.

Check the air pressure in the tires. Tires with too much air pressure will cause the unit to ride rough. Also, the wrong air pressure will keep the mower housing from cutting level. The correct air pressure is shown on the side of the tire.

CHECK THE LEVEL OF THE MOWER HOUSING

Make sure the level of cut is still correct. After you mow a short distance, look at the area that was cut. If the mower housing does not cut level, see the instructions on “How To Level The Mower Housing” in the Maintenance section of this instruction book.

F-050717L

13

Image 13
Contents Model Table of Contents Environmental Awareness OWNER’S InformationII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowInternational Pictorials Safety Warning PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Charge the Maintenance Free Battery Maintenance Free BatteryHOW to Assemble the Steering Wheel HOW to Install the SeatCheck the Level of the Mower Housing HOW to Prepare the EngineIMPORTANT! Before YOU Start Mowing Check the TiresLocation of Controls OperationLift Lever HOW to Operate the Ignition KEY Switch Electrical Safety SystemHOW to USE the Throttle Control AttachmentsHOW to USE the Shift Lever HOW to USE Blade Rotation ControlSee the Instruction Book for the Attachment HOW to Change the Cutting Height HOW to SET the Parking BrakeHOW to Stop the Unit HOW to Transport the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingBefore Starting the Engine HOW to Start the EngineCarburetor Mowing and Bagging Tips Operating TipsMaintenance Chart MaintenanceHOW to Check the Muffler General RecommendationsHOW to Sharpen the Blade HOW to Remove and Install the BladeInspect Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Clutch HOW to Check and Adjust the Drive BrakeHOW to Clean the Battery HOW to Check the Fuel Filter Where to LubricateHOW to Install the Mower Housing HOW to Remove the Mower HousingAttach the spark plug wire to the spark plug HOW to Level the Mower HousingRemoval HOW to Replace the Motion Drive BeltHOW to Replace the Mower Drive Belt Front Wheel HOW to Install the WheelsHOW to Replace the Light Bulb HOW to Replace the FuseHOW to Clean the Mower Housing BatteryTrouble Shooting Chart MURRAY, INC. Lawn Mower Central Parts Distributors 050717L Chassis & Hood Repair PartsKey Description Repair Parts Motion Drive Motion Drive Steering Key Part Description Mower Housing Suspension Repair Parts Mower Housing Key Description Repair Parts Engine Mount Repair Parts Wiring Harness for Electrical System 050717L Index Model No Bushel Capacity Model No

387002x92D specifications

Murray 387002x92D is an innovative and versatile machine designed for various industrial applications. This model has gained recognition for its robust build, cutting-edge technologies, and user-friendly features that enhance efficiency and productivity in a multitude of environments.

One of the standout characteristics of the Murray 387002x92D is its powerful engine, which provides significant torque and performance. This engine supports a variety of operations, from heavy lifting to complex machinery tasks. The durability of the engine ensures long-lasting performance, making it suitable for demanding industrial settings.

The machine is equipped with advanced hydraulic systems that facilitate smooth operation and precise control. These hydraulic features not only improve functionality but also enhance safety measures, allowing operators to perform tasks with greater confidence. The design ensures that hydraulic components are easily accessible for maintenance, thereby reducing downtime and extending the machine's lifespan.

Murray 387002x92D emphasizes user comfort and safety. The operator’s cabin is ergonomically designed, providing ample space and visibility. It includes intuitive controls that minimize the learning curve for new operators. Safety features, such as emergency stop systems and reinforced frames, ensure that both the operator and surrounding personnel are protected during operation.

In terms of technology, the model incorporates smart sensors that monitor performance and provide real-time feedback. This innovation allows for predictive maintenance, helping to identify potential issues before they lead to significant problems. Furthermore, the integration of digital dashboards provides operators with vital information at their fingertips, aiding in decision-making and operational efficiency.

Another notable feature of the Murray 387002x92D is its adaptability. With interchangeable attachments and modular components, this machine can be customized for specific tasks, making it an excellent investment for businesses looking to optimize their operations.

Moreover, the fuel efficiency of the Murray 387002x92D is commendable, aligning with modern sustainability goals. Lower fuel consumption not only reduces operational costs but also minimizes the environmental impact, making it an eco-friendly choice for conscientious businesses.

Overall, the Murray 387002x92D stands out as a reliable, efficient, and adaptable solution for various industrial applications. Its blend of power, technology, and user-centered design makes it an invaluable asset for enhancing productivity and ensuring safety in the workplace.