Murray 387002x92D manual Before Starting the Engine, Carburetor, HOW to Start the Engine

Page 19

OPERATION

BEFORE STARTING THE ENGINE

CHECK THE OIL

NOTE: The engine was shipped from the factory filled with oil. Check the level of the oil. Add oil as needed. See the engine manufacturer’s instructions for the type of gasoline and oil to use.

1.Make sure the unit is level.

NOTE: Do not check the level of the oil while the engine runs.

2.Check the oil. Follow the procedure in the engine manufactur- er’s instructions.

3.If necessary, add oil until the oil reaches the FULL mark on the dipstick. The quantity of oil needed from ADD to FULL is shown on the dipstick. Do not add too much oil.

CAUTION: A mixture of alcohol (ethanol or methanol) and gasoline (called gasohol), will attract moisture and cause acid deposits during storage. While the unit is in storage, the acids in the fuel can damage the fuel system.

To prevent engine problems with the fuel system, empty the fuel system before storage of 30 days or longer as follows.

1.Drain the fuel tank.

2.Start the engine. Let the engine run until the fuel lines and the carburetor are empty.

3.After storage, make sure you use fresh fuel. See the storage instructions for additional information.

4.Never use engine cleaner or carburetor cleaner in the fuel tank or permanent damage can occur.

ADD GASOLINE

WARNING: Always use a safety gasoline container. Do not smoke when adding gasoline to the fuel tank. Do not add gasoline when you are inside an enclo- sure. Before you add gasoline, stop the engine and let the engine cool for several minutes.

Fill the

fuel tank with regular

Fuel Tank

unleaded gasoline. Do not use

Full

premium

unleaded gasoline.

Make sure the gasoline is fresh

 

and clean. Leaded gasoline will

 

increase

deposits and shorten

 

the life of the valves.

CARBURETOR

The factory settings for the carburetor are for most conditions. If the engine is operated under the following conditions, you can adjust the carburetor mixture. To adjust the carburetor, see the engine manufacturer’s instructions.

1.The engine has a loss of power or does not run smooth.

2.A change from summer to winter operation.

3.A 40 degree change in the operation temperature. The carbure- tor was adjusted at 80 degrees at the factory.

4.The engine is operated above 4,000 feet.

HOW TO START THE ENGINE

WARNING: The electrical system has two primary components, an operator presence system and a Se- lect Reverset system. The operator presence sys- tem determines if the operator is sitting on the seat. This system will stop the engine when the operator leaves the seat. The Select Reverset system gives the operator the ability to temporarily mow in reverse if he decides such operation is absolutely necessary and safe operating precautions are taken. For your protection, always make sure these systems operate correctly.

NOTE: The engine will not start unless you depress the clutch/brake pedal or engage the parking brake and move the blade rotation control to the DISENGAGE position.

1.Make sure the spark plug wire is connected to the spark plug.

2.Push the clutch/brake pedal completely forward. Keep your foot on the pedal.

3.Move the shift lever to the neutral (N) position.

4.Make sure the blade rotation control is in the DISENGAGE position. If the blade rotation control is not in the DISENGAGE position, the engine will not start.

5.Move the throttle control completely forward to the CHOKE or FAST position. Some models have a separate choke knob. Pull the choke knob to the full CHOKE position.

6.Turn the ignition key to the START position. Release the key when the engine starts. The ignition key switch will auto- matically default to the recommended RUN-MOW position for normal mowing. See “How To Operate The Ignition Key Switch” in the Operation Section.

NOTE: If the engine does not start after four or five tries, see the TROUBLE SHOOTING CHART.

7.Slowly move the throttle control to the SLOW position.

8.Let a cold engine run for several minutes. Begin work when the engine is warm. To start a hot engine, move the throttle control to a position between FAST and SLOW.

F-050717L

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model Table of Contents Environmental Awareness OWNER’S InformationII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowControl And Operating Pictorials Safety Warning PictorialsInternational Pictorials International PictorialsAssembly AssemblyHOW to Charge the Maintenance Free Battery Maintenance Free BatteryHOW to Assemble the Steering Wheel HOW to Install the SeatCheck the Tires HOW to Prepare the EngineCheck the Level of the Mower Housing IMPORTANT! Before YOU Start MowingLocation of Controls OperationLift Lever Attachments Electrical Safety SystemHOW to Operate the Ignition KEY Switch HOW to USE the Throttle ControlHOW to USE the Shift Lever HOW to USE Blade Rotation ControlSee the Instruction Book for the Attachment HOW to Transport the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Stop the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingBefore Starting the Engine HOW to Start the EngineCarburetor Mowing and Bagging Tips Operating TipsGeneral Recommendations MaintenanceMaintenance Chart HOW to Check the MufflerHOW to Sharpen the Blade HOW to Remove and Install the BladeInspect Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Clutch HOW to Check and Adjust the Drive BrakeHOW to Clean the Battery HOW to Check the Fuel Filter Where to LubricateHOW to Install the Mower Housing HOW to Remove the Mower HousingAttach the spark plug wire to the spark plug HOW to Level the Mower HousingRemoval HOW to Replace the Motion Drive BeltHOW to Replace the Mower Drive Belt Front Wheel HOW to Install the WheelsBattery HOW to Replace the FuseHOW to Replace the Light Bulb HOW to Clean the Mower HousingTrouble Shooting Chart MURRAY, INC. Lawn Mower Central Parts Distributors 050717L Chassis & Hood Repair PartsKey Description Repair Parts Motion Drive Motion Drive Steering Key Part Description Mower Housing Suspension Repair Parts Mower Housing Key Description Repair Parts Engine Mount Repair Parts Wiring Harness for Electrical System 050717L Index Model No Bushel Capacity Model No

387002x92D specifications

Murray 387002x92D is an innovative and versatile machine designed for various industrial applications. This model has gained recognition for its robust build, cutting-edge technologies, and user-friendly features that enhance efficiency and productivity in a multitude of environments.

One of the standout characteristics of the Murray 387002x92D is its powerful engine, which provides significant torque and performance. This engine supports a variety of operations, from heavy lifting to complex machinery tasks. The durability of the engine ensures long-lasting performance, making it suitable for demanding industrial settings.

The machine is equipped with advanced hydraulic systems that facilitate smooth operation and precise control. These hydraulic features not only improve functionality but also enhance safety measures, allowing operators to perform tasks with greater confidence. The design ensures that hydraulic components are easily accessible for maintenance, thereby reducing downtime and extending the machine's lifespan.

Murray 387002x92D emphasizes user comfort and safety. The operator’s cabin is ergonomically designed, providing ample space and visibility. It includes intuitive controls that minimize the learning curve for new operators. Safety features, such as emergency stop systems and reinforced frames, ensure that both the operator and surrounding personnel are protected during operation.

In terms of technology, the model incorporates smart sensors that monitor performance and provide real-time feedback. This innovation allows for predictive maintenance, helping to identify potential issues before they lead to significant problems. Furthermore, the integration of digital dashboards provides operators with vital information at their fingertips, aiding in decision-making and operational efficiency.

Another notable feature of the Murray 387002x92D is its adaptability. With interchangeable attachments and modular components, this machine can be customized for specific tasks, making it an excellent investment for businesses looking to optimize their operations.

Moreover, the fuel efficiency of the Murray 387002x92D is commendable, aligning with modern sustainability goals. Lower fuel consumption not only reduces operational costs but also minimizes the environmental impact, making it an eco-friendly choice for conscientious businesses.

Overall, the Murray 387002x92D stands out as a reliable, efficient, and adaptable solution for various industrial applications. Its blend of power, technology, and user-centered design makes it an invaluable asset for enhancing productivity and ensuring safety in the workplace.
Top Page Image Contents