Murray 387002x92D manual HOW to Charge the Maintenance Free Battery

Page 11

ASSEMBLY

MAINTENANCE FREE BATTERY

IMPORTANT: Before you attach the battery cables to the battery, check the battery date. The battery date tells if the battery must be charged.

1.Check the top and the side of the battery for the location of the battery date (Figure 2).

2.If the battery is put into service before the battery date, the battery cables can be attached without charging the battery. See “How To Install The Battery Cables”.

3.If the battery is put into service after the battery date, the battery must be charged. See “How To Charge The Maintenance Free Battery”.

HOW TO CHARGE THE MAINTENANCE FREE BATTERY

WARNING: When you charge the battery, do not smoke. Keep the battery away from any sparks. The fumes from the battery acid can cause an explosion.

1.Remove the battery. See “How To Remove The Battery”.

2.Remove the protective cap from the battery terminal.

3.Use a 12 volt battery charger to charge the battery. Charge at a rate of 6 amperes for one hour. If you do not have a battery charger, have an authorized service center charge the battery.

4.Install the battery. See “How To Install The Battery”.

HOW TO REMOVE THE BATTERY

1.Rotate the battery clamp to the DOWN position (Figure 1 and Figure 2).

2.To remove the battery, tilt the battery forward and then lift the battery.

CAUTION: Do not tilt the battery more than 45 degrees. If the battery tilts more than 45 degrees, battery acid can leak from the battery.

UP - Operating Position

SIDE

Battery Clamp

 

VIEW

 

 

DOWN - Removal Position

 

Figure 1

HOW TO INSTALL THE BATTERY

1.Install the battery tray (Figure 3). Make sure the drain on the bottom of the battery tray goes through the hole in the frame as shown in Figure 3.

2.Turn the battery so that the positive (+) terminal is on the right side of the unit. Set the battery in the battery tray.

IMPORTANT: Make sure the battery fits under the tabs at the back of the unit.

3.Rotate the battery clamp to the UP position (Figure 1 and Figure 3).

HOW TO INSTALL THE BATTERY CABLES

WARNING: To prevent sparks, fasten the red cable to the positive (+) terminal before you connect the black cable.

NOTE: Before you attach the battery cables, make sure the battery is fully charged. This will extend the life of the battery and provide the necessary power to start the engine.

2.If equipped, slide the terminal cover onto the red cable (Figure 3). Fasten the red cable to the positive (+) terminal with the fasteners as shown. Push the terminal cover onto the battery terminal.

3.Fasten the black cable to the negative (-) terminal with the fas- teners as shown.

Battery Date Code

Battery

 

Battery Clamp

 

DOWN position

 

Figure 2

 

Black Cable

Tabs

A

 

 

B

A

B

 

Battery Clamp

Battery

UP Position

 

Red Cable

Terminal

Use the fasteners shown below to install the battery cables. The fasteners are shown at full size.

Positive (+)

Terminal

Cover

(A)

(B)

2x82

14x79

1.Remove the protective caps from the battery terminals.

Battery Tray

Drain

Figure 3

F-050717L

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model Table of Contents Environmental Awareness OWNER’S InformationII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowControl And Operating Pictorials Safety Warning PictorialsInternational Pictorials International PictorialsAssembly AssemblyHOW to Charge the Maintenance Free Battery Maintenance Free BatteryHOW to Assemble the Steering Wheel HOW to Install the SeatCheck the Tires HOW to Prepare the EngineCheck the Level of the Mower Housing IMPORTANT! Before YOU Start MowingLift Lever OperationLocation of Controls Attachments Electrical Safety SystemHOW to Operate the Ignition KEY Switch HOW to USE the Throttle ControlSee the Instruction Book for the Attachment HOW to USE Blade Rotation ControlHOW to USE the Shift Lever HOW to Transport the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Stop the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingCarburetor HOW to Start the EngineBefore Starting the Engine Mowing and Bagging Tips Operating TipsGeneral Recommendations MaintenanceMaintenance Chart HOW to Check the MufflerInspect Blade HOW to Remove and Install the BladeHOW to Sharpen the Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Clutch HOW to Check and Adjust the Drive BrakeHOW to Clean the Battery HOW to Check the Fuel Filter Where to LubricateHOW to Install the Mower Housing HOW to Remove the Mower HousingAttach the spark plug wire to the spark plug HOW to Level the Mower HousingRemoval HOW to Replace the Motion Drive BeltHOW to Replace the Mower Drive Belt Front Wheel HOW to Install the WheelsBattery HOW to Replace the FuseHOW to Replace the Light Bulb HOW to Clean the Mower HousingTrouble Shooting Chart MURRAY, INC. Lawn Mower Central Parts Distributors 050717L Chassis & Hood Repair PartsKey Description Repair Parts Motion Drive Motion Drive Steering Key Part Description Mower Housing Suspension Repair Parts Mower Housing Key Description Repair Parts Engine Mount Repair Parts Wiring Harness for Electrical System 050717L Index Model No Bushel Capacity Model No

387002x92D specifications

Murray 387002x92D is an innovative and versatile machine designed for various industrial applications. This model has gained recognition for its robust build, cutting-edge technologies, and user-friendly features that enhance efficiency and productivity in a multitude of environments.

One of the standout characteristics of the Murray 387002x92D is its powerful engine, which provides significant torque and performance. This engine supports a variety of operations, from heavy lifting to complex machinery tasks. The durability of the engine ensures long-lasting performance, making it suitable for demanding industrial settings.

The machine is equipped with advanced hydraulic systems that facilitate smooth operation and precise control. These hydraulic features not only improve functionality but also enhance safety measures, allowing operators to perform tasks with greater confidence. The design ensures that hydraulic components are easily accessible for maintenance, thereby reducing downtime and extending the machine's lifespan.

Murray 387002x92D emphasizes user comfort and safety. The operator’s cabin is ergonomically designed, providing ample space and visibility. It includes intuitive controls that minimize the learning curve for new operators. Safety features, such as emergency stop systems and reinforced frames, ensure that both the operator and surrounding personnel are protected during operation.

In terms of technology, the model incorporates smart sensors that monitor performance and provide real-time feedback. This innovation allows for predictive maintenance, helping to identify potential issues before they lead to significant problems. Furthermore, the integration of digital dashboards provides operators with vital information at their fingertips, aiding in decision-making and operational efficiency.

Another notable feature of the Murray 387002x92D is its adaptability. With interchangeable attachments and modular components, this machine can be customized for specific tasks, making it an excellent investment for businesses looking to optimize their operations.

Moreover, the fuel efficiency of the Murray 387002x92D is commendable, aligning with modern sustainability goals. Lower fuel consumption not only reduces operational costs but also minimizes the environmental impact, making it an eco-friendly choice for conscientious businesses.

Overall, the Murray 387002x92D stands out as a reliable, efficient, and adaptable solution for various industrial applications. Its blend of power, technology, and user-centered design makes it an invaluable asset for enhancing productivity and ensuring safety in the workplace.
Top Page Image Contents