Murray 387002x92D manual Trouble Shooting Chart

Page 33

TROUBLE SHOOTING CHART

PROBLEM: The engine will not start.

1.Follow the steps, “How To Start The Engine” in this book.

2.Electric-Start Models: Clean the battery terminals. Tighten the cables.

3.Drain the fuel tank. Clean the fuel line. Replace the fuel filter.

4.Remove the spark plug(s). Move the throttle to the SLOW posi- tion. Turn the ignition key to the ON position. Try to start the en- gine several times. Install the spark plug.

5.Replace the spark plug.

6.Adjust the carburetor.

PROBLEM: The engine will not turn over.

1.Follow the steps, “How To Start The Engine” in this book.

2.Electric-Start Models: Check the level of the acid in the battery. If needed, add water. Charge the battery.

3.Replace the fuse.

4.Check the wiring harness for damage or a loose connection. Repair the damaged wire.

5.Electric-Start Models: replace the solenoid. Recoil-Start Mod-

els: replace the module.

PROBLEM: The engine is difficult to start.

1.Adjust the carburetor.

2.Replace the spark plug.

3.Replace the fuel filter.

PROBLEM: The engine does not run smooth or has a loss of power.

1.Check the oil.

2.Clean the air filter.

3.Clean the air screen.

4.Replace the spark plug.

5.The engine is working too hard. Use a lower gear.

6.Adjust the carburetor.

7.Replace the fuel filter.

PROBLEM: The engine does not run smooth at fast speed.

1.Replace the spark plug.

2.Adjust the throttle control.

3.Clean the air filter.

4.Replace the fuel filter.

PROBLEM: The engine stops when the blades are engaged.

1.Check the wiring harness for damage or a loose connection. Repair the damaged wire.

2.Transmission is in reverse. Before operating in reverse, move the blade rotation control to the DISENGAGED position.

PROBLEM: On slopes, the engine stops.

1.Mow up and down slopes. Never mow across a slope.

2.To activate the seat sensor, always sit in the middle of the seat.

PROBLEM: The engine will not idle.

1.Replace the spark plug.

2.Clean the air filter.

3.Adjust the carburetor.

4.Adjust the throttle control.

5.Drain the fuel tank. Clean the fuel line. Replace the fuel filter.

PROBLEM: A hot engine causes a decrease in power.

1.Clean the air screen.

2.Check the oil.

3.Adjust the carburetor.

4.Replace the fuel filter.

PROBLEM: Excessive vibration.

1.Replace the blade.

2.Check for loose engine bolts.

3.Decrease the air pressure in the tires.

4.Adjust the carburetor.

5.Check for a damaged belt or damaged pulley. Replace the damaged parts.

PROBLEM: The grass does not discharge correctly.

1.Stop the engine. Clean the mower housing.

2.Raise the height of cut.

3.Replace or sharpen the blade(s).

4.Move the shift lever to a slower speed.

5.Move the throttle control to the FAST position.

6.Replace the spring for the blade idler.

PROBLEM: The mower housing does not cut level.

1.Check the air pressure in the tires.

2.Adjust the level of the mower housing.

3.Check the front axle. If the front axle does not freely pivot, loos- en the axle bolt(s).

PROBLEM: The mower blades will not rotate.

1.Check the mower drive belt. Make sure the belt is installed cor- rectly.

2.Replace the mower drive belt.

PROBLEM: The unit will not move when the clutch is engaged.

1.Check the motion drive belt. Make sure the belt is installed correctly.

2.Adjust the clutch.

3.Replace the motion drive belt.

PROBLEM: The unit moves slower or stops when the clutch is engaged.

1.Adjust the clutch.

2.Replace the motion drive belt.

PROBLEM: When the clutch/brake pedal is released, belt noise can be heard.

1.Temporary belt noise does not change the operation of the unit. If belt noise is continuous, check the routing of the belt. Make sure the belt is inside all belt guides.

2.If the noise is continuous, adjust the clutch.

PROBLEM: The rear wheels spin over uneven terrain.

1.Check the front axle. If the front axle does not freely pivot, loos- en the axle bolt(s).

PROBLEM: The engine stops when the operator leaves the seat.

1.This is normal. The operator presence system is designed to allow operation only if the operator is in the seat.

PROBLEM: The engine stops when selecting reverse travel.

1.Before selecting reverse travel, move the blade rotation control to the DISENGAGE position. See the Operation section for de- tails.

PROBLEM: The transaxle is difficult to shift between gears with the engine running and the clutch depressed.

1.Check the clutch adjustment to make sure the belt stops when the clutch pedal is depressed with the transaxle in (N) neutral.

2.Check the belt guides around the transaxle drive pulley. Make sure the belt guides do not touch the pulley.

F-050717L

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Model Table of Contents Environmental Awareness OWNER’S InformationII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowInternational Pictorials Safety Warning PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Charge the Maintenance Free Battery Maintenance Free BatteryHOW to Assemble the Steering Wheel HOW to Install the SeatCheck the Level of the Mower Housing HOW to Prepare the EngineIMPORTANT! Before YOU Start Mowing Check the TiresOperation Location of ControlsLift Lever HOW to Operate the Ignition KEY Switch Electrical Safety SystemHOW to USE the Throttle Control AttachmentsHOW to USE Blade Rotation Control HOW to USE the Shift LeverSee the Instruction Book for the Attachment HOW to Change the Cutting Height HOW to SET the Parking BrakeHOW to Stop the Unit HOW to Transport the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingHOW to Start the Engine Before Starting the EngineCarburetor Mowing and Bagging Tips Operating TipsMaintenance Chart MaintenanceHOW to Check the Muffler General RecommendationsHOW to Remove and Install the Blade HOW to Sharpen the BladeInspect Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Clutch HOW to Check and Adjust the Drive BrakeHOW to Clean the Battery HOW to Check the Fuel Filter Where to LubricateHOW to Install the Mower Housing HOW to Remove the Mower HousingAttach the spark plug wire to the spark plug HOW to Level the Mower HousingRemoval HOW to Replace the Motion Drive BeltHOW to Replace the Mower Drive Belt Front Wheel HOW to Install the WheelsHOW to Replace the Light Bulb HOW to Replace the FuseHOW to Clean the Mower Housing BatteryTrouble Shooting Chart MURRAY, INC. Lawn Mower Central Parts Distributors 050717L Chassis & Hood Repair PartsKey Description Repair Parts Motion Drive Motion Drive Steering Key Part Description Mower Housing Suspension Repair Parts Mower Housing Key Description Repair Parts Engine Mount Repair Parts Wiring Harness for Electrical System 050717L Index Model No Bushel Capacity Model No

387002x92D specifications

Murray 387002x92D is an innovative and versatile machine designed for various industrial applications. This model has gained recognition for its robust build, cutting-edge technologies, and user-friendly features that enhance efficiency and productivity in a multitude of environments.

One of the standout characteristics of the Murray 387002x92D is its powerful engine, which provides significant torque and performance. This engine supports a variety of operations, from heavy lifting to complex machinery tasks. The durability of the engine ensures long-lasting performance, making it suitable for demanding industrial settings.

The machine is equipped with advanced hydraulic systems that facilitate smooth operation and precise control. These hydraulic features not only improve functionality but also enhance safety measures, allowing operators to perform tasks with greater confidence. The design ensures that hydraulic components are easily accessible for maintenance, thereby reducing downtime and extending the machine's lifespan.

Murray 387002x92D emphasizes user comfort and safety. The operator’s cabin is ergonomically designed, providing ample space and visibility. It includes intuitive controls that minimize the learning curve for new operators. Safety features, such as emergency stop systems and reinforced frames, ensure that both the operator and surrounding personnel are protected during operation.

In terms of technology, the model incorporates smart sensors that monitor performance and provide real-time feedback. This innovation allows for predictive maintenance, helping to identify potential issues before they lead to significant problems. Furthermore, the integration of digital dashboards provides operators with vital information at their fingertips, aiding in decision-making and operational efficiency.

Another notable feature of the Murray 387002x92D is its adaptability. With interchangeable attachments and modular components, this machine can be customized for specific tasks, making it an excellent investment for businesses looking to optimize their operations.

Moreover, the fuel efficiency of the Murray 387002x92D is commendable, aligning with modern sustainability goals. Lower fuel consumption not only reduces operational costs but also minimizes the environmental impact, making it an eco-friendly choice for conscientious businesses.

Overall, the Murray 387002x92D stands out as a reliable, efficient, and adaptable solution for various industrial applications. Its blend of power, technology, and user-centered design makes it an invaluable asset for enhancing productivity and ensuring safety in the workplace.
Top Page Image Contents