Ingersoll-Rand SLB300, SLB200, SLB600, SLB1200, SLB150 Lubrication, Troubleshooting, General, Gear

Page 8

LUBRICATION

General

Thread lubricant or an anti-seize compound use is recommended for threaded shafts, capscrews and nuts. Unless otherwise stated, remove old lubricant, clean part with an acid free solvent and apply a new coating of lubricant to part before assembly.

Gear

Remove prevailing torque type nut (60) on side of hoist opposite hand lever and remove gear case assembly (1). Remove old grease and replace with new. For temperatures -29° to 10° C use EP 1 grease or equivalent. For temperatures -1° to 49° C use EP 2 grease or equivalent.

Load Chain

WARNING

•Failure to maintain clean and well lubricated load chain may result in chain failure causing injury, death or substantial property damage.

1.Lubricate each link of chain weekly. Apply new lubricant over existing layer.

2.In severe applications or corrosive environments, lubricate more frequently than normal.

3.Lubricate hook and hook latch pivot points with same lubricant used on load chain.

4.To remove rust or abrasive dust buildup, clean chain with an acid free solvent. After cleaning, lubricate chain.

5.Use Ingersoll Rand LUBRI-LINK-GREEN® or a SAE 50 to 90W EP oil.

TROUBLESHOOTING

This section provides basic troubleshooting information. Specific causes to problems are best identified by thorough inspections performed by personnel instructed in safety, operation and maintenance of this equipment. The chart below provides a brief guide to common hoist symptoms, probable causes and remedies.

.

SYMPTOM

CAUSE

REMEDY

Hoist will not hold

Brake may be slipping.

Inspect and adjust or repair as described in “INSPECTION” and “MAINTE-

rated load.

 

NANCE” sections.

Hoist will not lift

Excess slack in load chain.

Pull down on load chain while ratcheting until slack is removed and hoist

load.

 

begins lifting load. Refer to “OPERATION” section.

 

Hoist is overloaded.

Reduce load to within rated capacity.

 

Hoist is in NEUTRAL (N) mode.

Ensure selector lever is in UP position. Refer to “OPERATION” section.

Load chain binds.

Damaged load chain, pinion shaft, gears

Disassemble and inspect components as described in “MAINTENANCE”

 

or sheaves.

and “INSPECTION sections.

 

Load chain not installed properly

Inspect and adjust or repair as described in “INSPECTION” and “MAINTE-

 

(twisted, kinked or “capsized”).

NANCE” sections.

Load hook latch

Latch broken.

Replace hook latch.

does not work.

Load hook bent or twisted.

Inspect load hook as described in “INSPECTION” section. Replace if

 

 

necessary.

Hoist will not free

Brake is set.

Rotate free chain knob counterclockwise. Refer to “OPERATION” section.

chain.

 

 

8

MHD56109 - Edition 9

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Lever Chain Hoist Models Safety Information Safety SummarySpecifications Safe Operating InstructionsGeneral Model Code ExplanationInstallation OperationEnsure load is properly seated in saddle of bottom hook Lowering Load Down Position PayoutInspection Records and ReportsFrequent Inspection Load Chain ReportsPeriodic Inspection Semiannually QuarterlyModel Chain Size Normal Discard Length mmTroubleshooting LubricationGeneral GearMaintenance General DisassemblyHoist Disassembly Installing New Load ChainCleaning, Inspection and Repair Hoist AssemblyLoad Test Brake End AssemblyGear Timing Hoist Assembly Parts Drawing Hoist Assembly Parts List Description 75tLCCF015 Return Goods Policy AccessoriesParts Ordering Information Declaration Of Conformity MHD56109 Edition MHD56109 Edition Warranty Visible Loss or DamageConcealed Loss or Damage Damage ClaimsIngersoll-Rand

SLB150, SLB300, SLB1200, SLB600, SLB200 specifications

The Ingersoll-Rand SLB series of portable and stationary air compressors comprises several models, including the SLB200, SLB600, SLB1200, SLB150, and SLB300. These compressors are renowned for their reliability, performance, and innovative technologies, making them ideal for a wide range of industrial applications.

The SLB200 model comes equipped with a robust design that emphasizes mobility and efficiency. It features a compact footprint while delivering up to 200 CFM, making it suitable for smaller job sites or where space is limited. The SLB200 integrates advanced control systems that optimize airflow and pressure management, ensuring consistent performance under varying load conditions.

Next in the lineup is the SLB600, a powerhouse that delivers significantly higher capacity, reaching up to 600 CFM. This model offers advanced noise reduction technologies, which help minimize operational noise, making it an excellent choice for urban work sites. With its high-efficiency airend technology, the SLB600 also significantly improves fuel consumption, enabling cost-effective operation over the long term.

For those requiring even more power and versatility, the SLB1200 stands out, providing up to 1200 CFM. This model is engineered for heavy-duty applications, featuring durable construction that withstands rugged use. The SLB1200 comes equipped with advanced diagnostics and monitoring systems, allowing operators to track performance metrics in real-time. This feature enhances maintainability and helps prevent unexpected downtime.

The SLB150, while smaller, does not compromise on performance. Delivering 150 CFM, it is particularly valued in industries where portability is crucial. The SLB150 operates efficiently in both stationary and mobile applications, making it a favorite among contractors and repair professionals. Its lightweight design and integrated wheels ensure easy transport without sacrificing power.

Finally, the SLB300 model fills the gap for those needing a mid-range option with superior efficiency. Operating at up to 300 CFM, it strikes a balance between power and practicality. This model is equipped with enhanced filtration systems to ensure the highest air quality, which is essential for applications sensitive to contamination.

Overall, the Ingersoll-Rand SLB series is characterized by its commitment to innovation, reliability, and efficiency, catering to the diverse needs of modern industries while ensuring optimal performance and durability across all models.
Top Page Image Contents