Cleaning, Inspection and Repair

5.Remove change over pawl (22), spring shaft (23) and change over spring (24) from lever handle assembly (25).

6.Carefully pry change hand wheel (28) from change over gear (20).

7.Remove screw (64), washers (65) and prevailing torque type nut (60) from threaded spacers (94). Remove brake cover assembly (19).

8.Secure drive shaft (3) to prevent rotation and unscrew disk hub (15).

9.Remove friction disk (17), ratchet disk (18) and free spring (16).

10.Remove snap ring (63) from posts on side plate assembly B (12). Remove pawls (14) and pawl spring (13).

Accessing Gear End

1.Remove four prevailing torque type nuts (60) from side plate threaded spacers (94).

2.Remove gear case assembly (1).

3.Remove driver shaft assembly (2).

4.Remove snap ring (62) from load sheave assembly (7) if complete hoist is to be disassembled.

Accessing Load Sheave

Follow steps 1 through 10 in ‘Accessing Brake End’ and steps 1 through 4 in ‘Accessing Gear End’.

1.Slide out Drive shaft (3) from gear end.

2.Carefully remove side plate assembly B (brake side) (12).

3.Remove chain leaders (9) and (11), stripper (10), guide ring B (8) and top hook (45) with top pin (48).

4.Remove splined gear (4) from load sheave assembly (7). Remove load sheave from side plate assembly A (gear side)

(5).

5.Only if necessary, tap side plate threaded spacers (94) from side plate assembly A (gear side) (5).

Bottom Hook Disassembly

1.On single fall hoists remove prevailing torque type nut (77) and capscrew (52). Separate load chain from hook.

2.On 6 ton double fall hoists remove retainer rings (95).

3.Carefully slide idler sheave shaft (96) from hook block (57). Remove idler sheave (56) and remove rollers (97) from idler sheave (56).

4.Slide out idler sheave shaft (96) and remove bottom hook (51).

Use the following procedures to clean and inspect the components of hoist.

Cleaning

Clean all hoist component parts in solvent (except for brake disks). Use of a stiff bristle brush will facilitate removal of accumulated dirt and sediments on gears, shafts and housings. Dry each part using low pressure, filtered compressed air. If brake disks are oil-soaked, they must be replaced.

Inspection

All disassembled parts should be inspected to determine their fitness for continued use. Pay particular attention to the following:

1.Inspect all gears for worn, cracked, or broken teeth.

2.Inspect shafts for ridges caused by wear. If ridges caused by wear are apparent on shafts, replace shaft.

3.Inspect all threaded items and replace those having damaged threads.

4.Inspect brake disks for oil. If brake disks are oil-soaked, replace brake disks.

5.Measure thickness of brake disks. New brake disk thickness is 3 mm. Discard brake disks if thickness is 2 mm or less.

Repair

Actual repairs are limited to removal of small burrs and other minor surface imperfections. Use a fine stone or emery cloth for this work.

1.Worn or damaged parts must be replaced. Refer to applicable parts listing for specific replacement parts information.

2.Inspect all remaining parts for evidence of damage. Replace or repair any part which is in questionable condition. The cost of the part is often minor in comparison with the cost of redoing the job.

3.Smooth out all minor nicks, burrs, or galled spots on shafts, bores, pins or spacers.

4.Polish edges of all shaft shoulders to remove small nicks which may have been caused during handling.

5.Remove all nicks and burrs caused by lockwashers.

Hoist Assembly

Refer to Dwg. MHP0773 on page 12.

Load Sheave Assembly

1.Install side plate threaded spacers (94) in side plate assembly A (gear side) (5).

2.Install load sheave (7) in side plate assembly A (5).

3.Apply grease to Bearing A (91) located on end of load sheave (7).

4.Install chain leaders (9) and (11), stripper (10), guide ring B

(8) and top hook (45) on top pin (48) in side plate assembly A (5).

5.Carefully install side plate assembly B (brake end) (12) to engage locating diameters of parts installed in step 4.

6.Push side plates together to ensure all parts are located and secure.

Gear End Assembly

Follow steps 1 through 6 described in ‘Load Sheave Assembly’.

1.Install splined gear (4) on load sheave (7). Install snap ring

(62)on load sheave (7) to secure splined gear (4).

2.Install drive shaft (3) through center of load sheave (7).

3.Install driver shaft gears (2) so gear teeth are correctly timed and spigots locate in bearing sleeves in side plate assembly A (5). Refer to ‘Gear Timing’ section.

4.Apply a thick coat of grease as recommended in “LUBRICATION” section to all gear teeth. Install gear case

(1)over driver shaft (2) to locate and engage gear spigots.

5.Secure gear cover with prevailing torque type nut (60).

10	MHD56109 - Edition 9

SLB150, SLB300, SLB1200, SLB600, SLB200 specifications

The Ingersoll-Rand SLB series of portable and stationary air compressors comprises several models, including the SLB200, SLB600, SLB1200, SLB150, and SLB300. These compressors are renowned for their reliability, performance, and innovative technologies, making them ideal for a wide range of industrial applications.

The SLB200 model comes equipped with a robust design that emphasizes mobility and efficiency. It features a compact footprint while delivering up to 200 CFM, making it suitable for smaller job sites or where space is limited. The SLB200 integrates advanced control systems that optimize airflow and pressure management, ensuring consistent performance under varying load conditions.

Next in the lineup is the SLB600, a powerhouse that delivers significantly higher capacity, reaching up to 600 CFM. This model offers advanced noise reduction technologies, which help minimize operational noise, making it an excellent choice for urban work sites. With its high-efficiency airend technology, the SLB600 also significantly improves fuel consumption, enabling cost-effective operation over the long term.

For those requiring even more power and versatility, the SLB1200 stands out, providing up to 1200 CFM. This model is engineered for heavy-duty applications, featuring durable construction that withstands rugged use. The SLB1200 comes equipped with advanced diagnostics and monitoring systems, allowing operators to track performance metrics in real-time. This feature enhances maintainability and helps prevent unexpected downtime.

The SLB150, while smaller, does not compromise on performance. Delivering 150 CFM, it is particularly valued in industries where portability is crucial. The SLB150 operates efficiently in both stationary and mobile applications, making it a favorite among contractors and repair professionals. Its lightweight design and integrated wheels ensure easy transport without sacrificing power.

Finally, the SLB300 model fills the gap for those needing a mid-range option with superior efficiency. Operating at up to 300 CFM, it strikes a balance between power and practicality. This model is equipped with enhanced filtration systems to ensure the highest air quality, which is essential for applications sensitive to contamination.

Overall, the Ingersoll-Rand SLB series is characterized by its commitment to innovation, reliability, and efficiency, catering to the diverse needs of modern industries while ensuring optimal performance and durability across all models.