Agilent Technologies 5988-7401EN manual Setting Up a Clock Signal

Page 28

Setting Up Generic and Advanced Signals

Setting Up a Clock Signal

Setting Up a Clock Signal

Task Set up two clock signals with 100 MHz and 200 MHz frequencies, a

duty cycle of 50%, a high level of 1.0 V and a low level of 0 V.

Duty Cycle = 50%

1.0V

0.0V

f = 200 MHz	Duty Cycle = 50%

1.0 V

0.0 V

f = 100 MHz

Use Cases Generating clock signals can be used for:

•Boards evaluation

•Microprocessors

•A/D Converters

•PCI/PCI-X validation

•Digital ASIC design for high-speed HDD

28	Agilent 81133A/81134A Pulse Generator User’s Guide, January 2005

Image 28

Contents Agilent 81133A/81134A Pulse Generator Important Notice RevisionContents Setting Up Generic and Advanced Signals Setting Up the 81134A by Using the Graphical User InterfaceUpdating the Firmware Troubleshooting Index Contents Safety Summary Environmental ConditionsBefore Applying Power Safety RequirementsGround the Instrument Do not Operate in an Explosive AtmosphereInitial Inspection Initial InspectionPerformance Requirements Power RequirementsVentilation Requirements Cleaning Recommendation Cleaning RecommendationDeclaration of Conformity Declaration of ConformityIntroduction to the Agilent 81133A/81134A Pulse Generator Benefits and Key Features Introduction to the Agilent 81133A/81134A Pulse GeneratorFront Panel Overview Front Panel OverviewGraphical User Softkeys Numeric Interface Keys Tab Keys to navigateInput and Outputs Global Inputs Outputs Channel InputsDescription Rear Panel Overview Operating the Agilent 81133A/81134A Pulse Generator Navigation through the Pages Operating the Agilent 81133A/81134A Pulse GeneratorMain ChannelHow to Select a Parameter from a Selection List How to Navigate through the Parameters at onePress the navigation knob to open the selection list How to Change a Number Field How to Change a Number FieldModify Values Fine-Tuning Press Changing Single Digits Operating the Agilent 81133A/81134A Pulse Generator Setting Up Generic and Advanced Signals Setting Up a Clock Signal Setting Up Generic and Advanced SignalsUsing the Graphical User Interface Setting Up a Clock SignalNormal Out Channel Set the Freq. Divider to Frequency Divider Indicator Setting Up Generic and Advanced Signals Using the Remote Programming Interfaces Following code performs the same taskSetting Up a Pulse Signal Setting Up a Pulse Signal Pattern Mode Width LevelsTrigger Mode Generate the Signals //reconnect channels Setting Up a Data Pattern Prbs Polynome Signal Mode Pattern Mode Setting Up a Data PatternECL Levels Pulse Type NRZ Pattern Mode Data ECL Levels Switch to the Numeric Edit ModeData pattern for channel Numeric Edit Mode Trigger Mode Set up the trigger Set trigger mode to data OUTP0SOUR Bits Setting Up a Burst Signal Delay = 50 ps Period = 500 psArming Source Width = 100 psInstrument Setting Up a Burst SignalMode Data pattern for channel Graphic Edit Mode Timing ParameterTrigger Output Aux page now looks as follows Following code performs the same tasks Setting Up a Repetitive Burst Signal Burst Length = 4 x Data LengthSetting Up a Repetitive Burst Signal Instrument Burst Repetition Specifies ModeData Settings for the Pattern Signal To set the data pattern Setting Up a Repetitive Burst Signal Setting Up Generic and Advanced Signals Prepare the trigger Set trigger mode to Data OUTP0SOUR Bits Setting Up Signals for a Stressed Eye Diagram Measurement Setting Up Signals for a Stressed Eye Diagram Measurement Connecting the Instruments86100 DCA Setting Up the 81134A by Using Graphical User Interface 50 %Channel page now looks as follows Enable the trigger output Setting Up the 33250A Waveform Generator Viewing the Eye Diagram on the 86100 DCAPlay with the Settings Channel panelUsing the Agilent 81133A/81134A Pulse Generator Pages of the User Interface Using the Agilent 81133A/81134A Pulse GeneratorInstrument Panel Channel Pages of the User Interface Combining Parameters for Signal Generation Instrument ModesCombining Parameters for Signal Generation Pattern Modes Signal Modes NRZVariable Crossover Clock Sources Measure Function Clock SourceUsing the Agilent 81133A/81134A Pulse Generator Start Mode Trigger OutTiming of Generated Signals Timing of Generated Signals ClockDuty Cycle = 50 % Output Trigger OutPulses Channel Freq. Divider =Output Trigger Out Data PatternData Pattern of 32 bits Prbs Started Burst Data Pattern BurstRepetitive Burst Jitter Modulation Saving and Recalling SettingsJitter Modulation Saving and Recalling Settings Updating the Firmware Updating the Firmware Troubleshooting Troubleshooting Instrument does not RespondIndex IndexTrigger output levels Index 5988-7401EN