Agilent Technologies 5988-7401EN manual Setting Up a Data Pattern, ECL Levels

Page 41

Setting Up a Data Pattern

Setting Up Generic and Advanced Signals

6Enable the Channel 1 normal Output:

By pressing the respective softkey in the user interface:

– OR –

By pressing the normal Out softkey for channel 1 next to the Output port.

The Channel page now looks as follows:

PRBS Polynome

Signal Mode

Pattern Mode

PRBS

ECL Levels

Channel Settings for the

To set the channel parameters for channel 2:

 

Pattern Signal

 

 

 

 

 

1

Switch to Channel 2 by pressing the Ch2 softkey

.

 

2

Switch to the Channel page.

 

 

3

Select the pattern mode Data.

 

 

4

Select the signal mode NRZ.

 

 

5

In the Levels panel, select the predefined level format ECL.

 

 

This automatically sets:

 

 

 

– the Amplitude to 800 mV

 

 

 

–

the Offset to –1.350 V

 

 

 

–

the Term. Voltage to –2.0 V

 

Agilent 81133A/81134A Pulse Generator User’s Guide, January 2005

41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Agilent 81133A/81134A Pulse Generator Revision Important NoticeContents Setting Up the 81134A by Using the Graphical User Interface Setting Up Generic and Advanced SignalsUpdating the Firmware Troubleshooting Index Contents Environmental Conditions Safety SummarySafety Requirements Before Applying PowerGround the Instrument Do not Operate in an Explosive AtmosphereInitial Inspection Initial InspectionVentilation Requirements Power RequirementsPerformance Requirements Cleaning Recommendation Cleaning RecommendationDeclaration of Conformity Declaration of ConformityIntroduction to the Agilent 81133A/81134A Pulse Generator Introduction to the Agilent 81133A/81134A Pulse Generator Benefits and Key FeaturesFront Panel Overview Front Panel OverviewGraphical User Softkeys Numeric Interface Keys Tab Keys to navigateGlobal Inputs Outputs Channel Inputs Input and OutputsDescription Rear Panel Overview Operating the Agilent 81133A/81134A Pulse Generator Operating the Agilent 81133A/81134A Pulse Generator Navigation through the PagesMain ChannelHow to Navigate through the Parameters at one How to Select a Parameter from a Selection ListPress the navigation knob to open the selection list How to Change a Number Field How to Change a Number FieldPress Modify Values Fine-TuningChanging Single Digits Operating the Agilent 81133A/81134A Pulse Generator Setting Up Generic and Advanced Signals Setting Up Generic and Advanced Signals Setting Up a Clock SignalSetting Up a Clock Signal Using the Graphical User InterfaceNormal Out Channel Set the Freq. Divider to Frequency Divider Indicator Setting Up Generic and Advanced Signals Following code performs the same task Using the Remote Programming InterfacesSetting Up a Pulse Signal Pattern Mode Width Levels Setting Up a Pulse Signal Trigger Mode Generate the Signals //reconnect channels Setting Up a Data Pattern ECL Levels Setting Up a Data PatternPrbs Polynome Signal Mode Pattern Mode Switch to the Numeric Edit Mode Pulse Type NRZ Pattern Mode Data ECL LevelsData pattern for channel Numeric Edit Mode Trigger Mode Set up the trigger Set trigger mode to data OUTP0SOUR Bits Delay = 50 ps Period = 500 ps Setting Up a Burst SignalArming Source Width = 100 psMode Setting Up a Burst SignalInstrument Timing Parameter Data pattern for channel Graphic Edit ModeTrigger Output Aux page now looks as follows Following code performs the same tasks Burst Length = 4 x Data Length Setting Up a Repetitive Burst SignalInstrument Burst Repetition Specifies Mode Setting Up a Repetitive Burst SignalData Settings for the Pattern Signal To set the data pattern Setting Up a Repetitive Burst Signal Setting Up Generic and Advanced Signals Prepare the trigger Set trigger mode to Data OUTP0SOUR Bits Setting Up Signals for a Stressed Eye Diagram Measurement 86100 DCA Connecting the InstrumentsSetting Up Signals for a Stressed Eye Diagram Measurement 50 % Setting Up the 81134A by Using Graphical User InterfaceChannel page now looks as follows Enable the trigger output Viewing the Eye Diagram on the 86100 DCA Setting Up the 33250A Waveform GeneratorChannel panel Play with the SettingsUsing the Agilent 81133A/81134A Pulse Generator Instrument Panel Channel Using the Agilent 81133A/81134A Pulse GeneratorPages of the User Interface Pages of the User Interface Instrument Modes Combining Parameters for Signal GenerationCombining Parameters for Signal Generation Pattern Modes NRZ Signal ModesVariable Crossover Measure Function Clock Source Clock SourcesUsing the Agilent 81133A/81134A Pulse Generator Trigger Out Start ModeTiming of Generated Signals Clock Timing of Generated SignalsDuty Cycle = 50 % Output Trigger OutChannel Freq. Divider = PulsesData Pattern of 32 bits Data PatternOutput Trigger Out Prbs Data Pattern Burst Started BurstRepetitive Burst Jitter Modulation Saving and Recalling SettingsJitter Modulation Saving and Recalling Settings Updating the Firmware Updating the Firmware Troubleshooting Instrument does not Respond TroubleshootingIndex IndexTrigger output levels Index 5988-7401EN
Top Page Image Contents