Agilent Technologies 5988-7401EN manual Clock Sources, Measure Function Clock Source

Page 73

Combining Parameters for Signal Generation

Using the Agilent 81133A/81134A Pulse Generator

Clock Sources

The selected clock source defines the time base from which all other

timing parameters are derived. You can select between:

Internal

The clock is derived from the internal YIG oscillator.

External

external 10 MHz reference (clock source); clock sources:external 10 MHz reference

Enable the external clock input (Clock In) to accept an external clock signal that forms the time base. The frequency is measured once by selecting the Measure function from the user interface or as a remote SCPI command (:MEASure:FREQuency?).

Measure Function

Clock Source

This value is then used to calculate frequency-dependent values, like the pulse width or the phase (available at the Channel page).

For more information about the Measure function, please refer to the Online Help.

External 10 MHz Reference

ext. direct (clock source); clock sources:ext. direct

Enables the external clock input (Clock In) to apply a 10 MHz reference clock. This clock is used as a reference for all timing parameters.

Int. Direct/Ext. Direct

The direct modes allow changes of frequency without dropouts in the range of 1:2. They are used for applications (precise clock source) where dropouts would make a measurement impossible, for example, PLL frequency sweeps and microprocessor clock sweeps.

Agilent 81133A/81134A Pulse Generator User’s Guide, January 2005

73

Image 73
Contents Agilent 81133A/81134A Pulse Generator Revision Important NoticeContents Setting Up the 81134A by Using the Graphical User Interface Setting Up Generic and Advanced SignalsUpdating the Firmware Troubleshooting Index Contents Environmental Conditions Safety SummarySafety Requirements Before Applying PowerGround the Instrument Do not Operate in an Explosive AtmosphereInitial Inspection Initial InspectionPerformance Requirements Power RequirementsVentilation Requirements Cleaning Recommendation Cleaning RecommendationDeclaration of Conformity Declaration of ConformityIntroduction to the Agilent 81133A/81134A Pulse Generator Introduction to the Agilent 81133A/81134A Pulse Generator Benefits and Key FeaturesFront Panel Overview Front Panel OverviewGraphical User Softkeys Numeric Interface Keys Tab Keys to navigateGlobal Inputs Outputs Channel Inputs Input and OutputsDescription Rear Panel Overview Operating the Agilent 81133A/81134A Pulse Generator Operating the Agilent 81133A/81134A Pulse Generator Navigation through the PagesMain ChannelHow to Navigate through the Parameters at one How to Select a Parameter from a Selection ListPress the navigation knob to open the selection list How to Change a Number Field How to Change a Number FieldPress Modify Values Fine-TuningChanging Single Digits Operating the Agilent 81133A/81134A Pulse Generator Setting Up Generic and Advanced Signals Setting Up Generic and Advanced Signals Setting Up a Clock SignalSetting Up a Clock Signal Using the Graphical User InterfaceNormal Out Channel Set the Freq. Divider to Frequency Divider Indicator Setting Up Generic and Advanced Signals Following code performs the same task Using the Remote Programming InterfacesSetting Up a Pulse Signal Pattern Mode Width Levels Setting Up a Pulse SignalTrigger Mode Generate the Signals //reconnect channels Setting Up a Data Pattern Prbs Polynome Signal Mode Pattern Mode Setting Up a Data PatternECL Levels Switch to the Numeric Edit Mode Pulse Type NRZ Pattern Mode Data ECL LevelsData pattern for channel Numeric Edit Mode Trigger Mode Set up the trigger Set trigger mode to data OUTP0SOUR Bits Delay = 50 ps Period = 500 ps Setting Up a Burst SignalArming Source Width = 100 psInstrument Setting Up a Burst SignalMode Timing Parameter Data pattern for channel Graphic Edit ModeTrigger Output Aux page now looks as follows Following code performs the same tasks Burst Length = 4 x Data Length Setting Up a Repetitive Burst SignalInstrument Burst Repetition Specifies Mode Setting Up a Repetitive Burst SignalData Settings for the Pattern Signal To set the data pattern Setting Up a Repetitive Burst Signal Setting Up Generic and Advanced Signals Prepare the trigger Set trigger mode to Data OUTP0SOUR Bits Setting Up Signals for a Stressed Eye Diagram Measurement Setting Up Signals for a Stressed Eye Diagram Measurement Connecting the Instruments86100 DCA 50 % Setting Up the 81134A by Using Graphical User InterfaceChannel page now looks as follows Enable the trigger output Viewing the Eye Diagram on the 86100 DCA Setting Up the 33250A Waveform GeneratorChannel panel Play with the SettingsUsing the Agilent 81133A/81134A Pulse Generator Pages of the User Interface Using the Agilent 81133A/81134A Pulse GeneratorInstrument Panel Channel Pages of the User Interface Instrument Modes Combining Parameters for Signal GenerationCombining Parameters for Signal Generation Pattern Modes NRZ Signal ModesVariable Crossover Measure Function Clock Source Clock SourcesUsing the Agilent 81133A/81134A Pulse Generator Trigger Out Start ModeTiming of Generated Signals Clock Timing of Generated SignalsDuty Cycle = 50 % Output Trigger OutChannel Freq. Divider = PulsesOutput Trigger Out Data PatternData Pattern of 32 bits Prbs Data Pattern Burst Started BurstRepetitive Burst Jitter Modulation Saving and Recalling SettingsJitter Modulation Saving and Recalling Settings Updating the Firmware Updating the Firmware Troubleshooting Instrument does not Respond TroubleshootingIndex IndexTrigger output levels Index 5988-7401EN

5988-7401EN specifications

Agilent Technologies, a leader in life sciences, diagnostics, and applied chemical markets, offers an array of sophisticated tools aimed at enhancing analytical and diagnostic capabilities. One such product is the Agilent 5988-7401EN, a high-performance mass spectrometer that exemplifies cutting-edge technology in the field of analytical chemistry.

The Agilent 5988-7401EN is part of a series of mass spectrometers designed to deliver exceptional sensitivity and resolution for a variety of applications. This advanced instrument is particularly well-known for its versatility in mass spectrometry, enabling researchers to perform complex analyses with ease. Its flexibility makes it suitable for various industries, including pharmaceuticals, environmental testing, and food safety.

One of the standout features of the 5988-7401EN is its groundbreaking technology in ion detection. This mass spectrometer utilizes a unique technology that significantly enhances ion transmission and improves signal-to-noise ratios, resulting in more reliable and reproducible data. This capability is critical for trace analysis, where detecting low-abundance compounds is essential.

Moreover, the 5988-7401EN offers a wide mass range and fast scan speeds, making it suitable for both small molecule identification and larger biomolecules. This instrument can analyze complex mixtures with high accuracy, which is vital for researchers needing to understand intricate chemical compositions.

Additionally, the user-friendly interface of Agilent's mass spectrometer enhances productivity. With streamlined software that allows for easy operation and data analysis, researchers can efficiently set up experiments and interpret results, saving time and reducing the likelihood of human error.

Another important characteristic is its robustness and reliability. Built to withstand the demands of routine laboratory use, the 5988-7401EN ensures consistent performance over time, which is crucial for laboratories with high workloads.

In summary, the Agilent 5988-7401EN represents a significant advancement in mass spectrometry technology. With its impressive features, including exceptional sensitivity, a wide mass range, rapid scan speeds, and user-friendly software, it is an invaluable tool for researchers across various scientific disciplines. Whether it's for pharmaceutical development, environmental analysis, or food safety testing, the 5988-7401EN is designed to meet and exceed the analytical needs of modern laboratories.