Craftsman 917.27066 Brake Operation, Tires, Operator Presence System, Blade Care, Blade Removal

Page 19

"rRACTOR

Always observe safety rules when

performing any maintenance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be ad- justed. (See 'q-OADJUST BRAKE" in the

Service and Adjustments section of this manual).

TIRES

Maintain proper air pressure in all tires (See "PRODUCT SPECIFICATIONS" section of this manual).

Keep tires free of gasoline, oil, or insect control chemicals which can harm

rubber.

Avoid stumps, stones, deep ruts, sharp objects and other hazards that may

cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts

dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure that operator presence and interlock systems are working properly. If your tractor does not function as de- scribed below, repair the problem immediately.

The engine should not start unless the

clutch/brake pedal is fully depressed and attachment clutch control is in the

disengaged position.

When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

The attachment clutch should never

operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be

kept sharp. Replace bent or damaged blades.

BLADE REMOVAL

Raise mower to highest position to allow access to blades.

Remove hex bolt, lock washer and flat washer securing blade.

Install new or resharpened blade with

trailing edge up towards deck as shown.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

Reassemble hex bolt, lock washer and flat washer in exact order as shown.

Tighten bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: Blade bolt is Grade 8 heat

treated.

 

Mandrel

Trailing \

Blade

Assembly

Edge Up_

Hole

_._"_

Center

_'_

Lock

_

tar

Flat Washer,,_,_ _

 

_"_'Hex Bolt (Grade 8)*

*A Grade 8 heat treated bolt can be

identified by six lines on the bolt head.

TO SHARPEN BLADE

NOTE: We do not recommend sharpening

blade, but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and eventual

damage to mower and engine.

The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while it is on the mower.

To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone bal-

ancer, follow the instructions supplied with balancer).

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

Slide blade onto an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

Center Hole

Blade

5/8" Bolt or Pin

19

Image 19
Contents Sears Craftsman Help Line 5 am 5 pro, Mon- Sat CraftsmanGeneral Operation Limited TWO Year Warranty on Craftsman Riding EquipmentRrnnvA kmw hAfnr limnltnfinn Do not ServiceSerious injury Slope OperationPeople before mowing. Stop machine if anyone enters the area Mntenanceagreement Product SpecificationsCustomer Responsibiuties Parts BAG Contents Shown Full Size Steering Mulcher Separately in cartonSteering WheelBefore Rolung Tractor OFF Skid Attach Steering Wheel To Remove Tractor from CartonCheck Deck Levelness Install SeatTo Drive Tractor OFF Skid Check Tire PressureDischarging ChecklistInstall Mulcher Plate To Convert to Bagging orH L Know Your Tractor Mower Blades HOW to USE Your TractorStopping To SET Parking BrakeTo Transport Towing Carts and Other AttachmentsTo Operate Mower To Operate on HillsTo Start Engine ADD GasouneAutomatic Transmission Warm UP Mowing Tips Purge TransmissionImportant For best performance, keep Mulching Mowing TipsCustomer General Recommendations Lubrication ChartBefore Each USE Blade Care Brake OperationTires Operator Presence SystemEngine IN-UNE Fuel Filter Clean AIR ScreenMuffler Spark PlugsSuspension Arms Rod Retainer Spring Anti-Swaybar CleaningTo Install Mower To Remove MowerTo Replace Mower Blade Drive Belt Raise mower to its highest positionNut F Front LinksNut To Adjust BrakePulley Center/departmentTransmission REMOVAL/REPLACE- Ment Transaxle Motion Control LE- VER AdjustmentTo Adjust Steering Wheel ALIGN- Ment To Start Engine That has a Weak BatteryTo Replace Fuse Replacing BatteryTo Replace Headlight Bulb Interlocks and RelaysGovernor To Adjust THROI-rLE Control CableTo Adjust Carburetor EngineThrottle Acceleration TestIdle Speed Engine OIL BatteryTo Clean Batteryand Termi Fuel SystemProblem Troubleshooting HartCause Problem Troubleshooting ChartCorrection Troubleshooting Chart Tractor Model Number SchematicTractor - Model Number ElectricalElectrical Tractor - Model NumberNO. NO.DESCRIPTION Tractor - Model Number Chassis and Enclosures KEY Part NO. NO.DESCRIPTION Tractor - Model Number Ground Drive KEY Part Description Tractor - Model Number Steering Assembly Washer 13/32 x 1-1/4 x 12 Ga Bolt Hex Nylon 3/8-16 x 3/4 KEY Part NO. no66 1544O4 ScrewOPTIONALSpark ArresterEQUIPMENT Tractor - Model Number Engine17720410 162157165291 155925 Pan Pnt Seat blk 127018 BoltShoulder5/16-18X 166369 Tractor --MODEL Number Seat AssemblyKEY KEY Part156811 167179 1632oo Wheels & Tires133644 166887 163204 Tractor - Model Number Lift Assembly 163552 12721873540600 Lo3- \/i Mower Deck14,18 Washer, Hardened 164961 MowerHousing STD533107 Bolt 138017Front 138440 RetainerSpdngTractor - Model Number Hydro Transaxle - Model Number X 1.5 x 16 x 7/8 x135 144608 Pin, Cotter 142951 Oil Filter Element 139 150775 614 2301026 127 138 106 987 95 117 634 634A Carburetor Gasket SET Gasket SET783 728 201544 474494385 Cover,Air Cleaner Counterweight AssemblyPin, Counterweight 356 497708 Wire Assembly Haust 358 495993 Gasket Set 872Page Only Ride UP and Down Hill Not Across Hill Suggested Guide for Sighting Slopes for Safe OperationHome CentralsM

917.27066 specifications

The Craftsman 917.27066 is a powerful and reliable riding lawn mower designed to make lawn maintenance a hassle-free task. This model combines a strong build quality with modern technology, catering to homeowners who value efficiency and performance in yard care.

One of the standout features of the Craftsman 917.27066 is its robust engine. Equipped with a 19 horsepower Briggs & Stratton engine, it delivers ample power that allows it to tackle various terrains with ease. This engine is designed for durability and efficiency, ensuring that users can cover more ground without frequent refueling.

The mower includes a 42-inch cutting deck, which provides a well-balanced cutting width perfect for medium-sized lawns. The size of the deck facilitates a clean and precise cut, ensuring that users can achieve a professional-looking finish in minimal time. The adjustable cutting height feature, with multiple settings, allows users to customize the grass length to meet their specific lawn care needs.

In terms of technology, the Craftsman 917.27066 features an electric start for convenient operation. This means no more pulling on a starter cord repeatedly; simply turn the key, and you're ready to mow. The adjustable seat adds to the comfort, making it suitable for extended use during those long mowing sessions.

The ergonomically designed steering wheel and intuitive control layout enhance the user experience by making the mower easy to maneuver. The tight turning radius enables users to navigate around flowerbeds, trees, and other obstacles, ensuring a thorough cut without leaving unkempt patches.

Another notable characteristic is the transmission system. The Craftsman 917.27066 features a hydrostatic drive system, which provides seamless speed adjustments and enhances overall ease of use. This is particularly beneficial for beginners who may find traditional gear transmissions challenging.

Moreover, the mower is designed with durability in mind. Its reinforced frame and heavy-duty materials ensure it can withstand the wear and tear of regular use. The incorporation of safety features, such as a safety switch that stops the engine when the operator leaves the seat, adds an extra layer of protection for users.

Overall, the Craftsman 917.27066 is a versatile and powerful riding lawn mower that combines ease of use, comfort, and efficiency, making it an excellent choice for homeowners who want to maintain their lawns effortlessly. Whether tackling flat surfaces or uneven terrain, this mower provides a dependable solution for all your lawn care needs.