Craftsman 917.27066 Transmission REMOVAL/REPLACE- Ment, To Adjust Steering Wheel ALIGN- Ment

Page 25

TRANSMISSION REMOVAL/REPLACE- MENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See "PURGE

TRANSMISSION" in the Operation section of this manual.

TRANSAXLE MOTION CONTROL LE- VER ADJUSTMENT

The motion control lever has been preset at the factory and adjustment should not be necessary.

If for any reason the motion control lever will not hold its position while at a selected speed, it may be adjusted as follows:

Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

Start engine and move motion control lever until tractor does not move forward or backward.

Hold motion control lever in that position and turn engine off.

While holding motion control lever in place, loosen the adjustment bolt.

Move motion control lever to the neutral

(N)(lock gate) position.

Tighten adjustment bolt securely.

NOTE: If additonal clearance is needed to

get to adjustment bolt, move mower aeck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

Loosen the adjustment bolt.

Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

Tighten adjustment bolt securely.

Start engine and test.

If tractor still creeps, repeat above steps until satisfied.

Motion Control Lever

Neutral

 

 

Gate

 

 

,Adjustment

/

.--_-. 1

Bolt

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steering wheel and reassemble per

instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not

adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or

camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS

Block up axle securely.

Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

Repair tire and reassemble.

On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

Replace washers and snap retaining ring securely in axle groove.

Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts

dealer. 13re sealant also prevents tire dry rot and corrosion.

Washers

Retaining

Rin ___,

Axle Cover "_ Square Key

(Rear Wheel Only)

TO START ENGINE THAT HAS A WEAK BATTERY

_CAUTION: Lead-acid batteries gener- ate explosive gases. Keep sparks, flame and smoking materials away from batter-

ies. Always wear eye protection when around batteries.

If your battery is too weak to start the en-

gine, it should be recharged. (See "BAT-

TERY" in the MAINTENANCE section of this manual).

If "jumper cables" are used for emergency starting, follow this procedure:

IMPORTANT: Your tractor Is equiped with a 12 volt negative grounded system. The other vehical must also be a 12 volt nega- tive grounded system. Do not use your tractor battery to start other vehicals.

25

Image 25
Contents Sears Craftsman Help Line 5 am 5 pro, Mon- Sat CraftsmanGeneral Operation Limited TWO Year Warranty on Craftsman Riding EquipmentRrnnvA kmw hAfnr limnltnfinn Serious injury ServiceSlope Operation Do notPeople before mowing. Stop machine if anyone enters the area Mntenanceagreement Product SpecificationsCustomer Responsibiuties Parts BAG Contents Shown Full Size Steering Separately in cartonWheel Steering MulcherBefore Rolung Tractor OFF Skid Attach Steering Wheel To Remove Tractor from CartonTo Drive Tractor OFF Skid Install SeatCheck Tire Pressure Check Deck LevelnessInstall Mulcher Plate ChecklistTo Convert to Bagging or DischargingH L Know Your Tractor Stopping HOW to USE Your TractorTo SET Parking Brake Mower BladesTo Operate Mower Towing Carts and Other AttachmentsTo Operate on Hills To TransportTo Start Engine ADD GasouneAutomatic Transmission Warm UP Mowing Tips Purge TransmissionImportant For best performance, keep Mulching Mowing TipsCustomer General Recommendations Lubrication ChartBefore Each USE Tires Brake OperationOperator Presence System Blade CareEngine Muffler Clean AIR ScreenSpark Plugs IN-UNE Fuel FilterTo Install Mower CleaningTo Remove Mower Suspension Arms Rod Retainer Spring Anti-SwaybarNut F Raise mower to its highest positionFront Links To Replace Mower Blade Drive BeltPulley To Adjust BrakeCenter/department NutTo Adjust Steering Wheel ALIGN- Ment Transaxle Motion Control LE- VER AdjustmentTo Start Engine That has a Weak Battery Transmission REMOVAL/REPLACE- MentTo Replace Headlight Bulb Replacing BatteryInterlocks and Relays To Replace FuseTo Adjust Carburetor To Adjust THROI-rLE Control CableEngine GovernorThrottle Acceleration TestIdle Speed To Clean Batteryand Termi BatteryFuel System Engine OILProblem Troubleshooting HartCause Problem Troubleshooting ChartCorrection Troubleshooting Chart Tractor Model Number SchematicTractor - Model Number ElectricalElectrical Tractor - Model NumberNO. NO.DESCRIPTION Tractor - Model Number Chassis and Enclosures KEY Part NO. NO.DESCRIPTION Tractor - Model Number Ground Drive KEY Part Description Tractor - Model Number Steering Assembly 66 1544O4 KEY Part NO. noScrew Washer 13/32 x 1-1/4 x 12 Ga Bolt Hex Nylon 3/8-16 x 3/4OPTIONALSpark ArresterEQUIPMENT Tractor - Model Number Engine17720410 162157165291 KEY Tractor --MODEL Number Seat AssemblyKEY Part 155925 Pan Pnt Seat blk 127018 BoltShoulder5/16-18X 166369156811 167179 1632oo Wheels & Tires133644 166887 163204 Tractor - Model Number Lift Assembly 163552 12721873540600 Lo3- \/i Mower Deck14,18 Front 138440 164961 MowerHousing STD533107 Bolt 138017RetainerSpdng Washer, HardenedTractor - Model Number Hydro Transaxle - Model Number X 1.5 x 16 x 7/8 x135 144608 Pin, Cotter 142951 Oil Filter Element 139 150775 614 2301026 127 138 106 987 95 117 634 634A Carburetor Gasket SET Gasket SET544 201474 783 728494385 Pin, Counterweight Counterweight Assembly356 497708 Wire Assembly Haust 358 495993 Gasket Set 872 Cover,Air CleanerPage Only Ride UP and Down Hill Not Across Hill Suggested Guide for Sighting Slopes for Safe OperationHome CentralsM

917.27066 specifications

The Craftsman 917.27066 is a powerful and reliable riding lawn mower designed to make lawn maintenance a hassle-free task. This model combines a strong build quality with modern technology, catering to homeowners who value efficiency and performance in yard care.

One of the standout features of the Craftsman 917.27066 is its robust engine. Equipped with a 19 horsepower Briggs & Stratton engine, it delivers ample power that allows it to tackle various terrains with ease. This engine is designed for durability and efficiency, ensuring that users can cover more ground without frequent refueling.

The mower includes a 42-inch cutting deck, which provides a well-balanced cutting width perfect for medium-sized lawns. The size of the deck facilitates a clean and precise cut, ensuring that users can achieve a professional-looking finish in minimal time. The adjustable cutting height feature, with multiple settings, allows users to customize the grass length to meet their specific lawn care needs.

In terms of technology, the Craftsman 917.27066 features an electric start for convenient operation. This means no more pulling on a starter cord repeatedly; simply turn the key, and you're ready to mow. The adjustable seat adds to the comfort, making it suitable for extended use during those long mowing sessions.

The ergonomically designed steering wheel and intuitive control layout enhance the user experience by making the mower easy to maneuver. The tight turning radius enables users to navigate around flowerbeds, trees, and other obstacles, ensuring a thorough cut without leaving unkempt patches.

Another notable characteristic is the transmission system. The Craftsman 917.27066 features a hydrostatic drive system, which provides seamless speed adjustments and enhances overall ease of use. This is particularly beneficial for beginners who may find traditional gear transmissions challenging.

Moreover, the mower is designed with durability in mind. Its reinforced frame and heavy-duty materials ensure it can withstand the wear and tear of regular use. The incorporation of safety features, such as a safety switch that stops the engine when the operator leaves the seat, adds an extra layer of protection for users.

Overall, the Craftsman 917.27066 is a versatile and powerful riding lawn mower that combines ease of use, comfort, and efficiency, making it an excellent choice for homeowners who want to maintain their lawns effortlessly. Whether tackling flat surfaces or uneven terrain, this mower provides a dependable solution for all your lawn care needs.