Craftsman C944.511591 instruction manual Er oe ino

Page 5

CARTONCONTENTS

5. Before using

the unit, tighten the

Checkcartoncontentsagainstthefol-

knob securely

by turning clock-

lowinglist.

wise.

 

Model0944.511591

 

 

• Brushcutterattachment

Coupler

Pnmary Hole

• Handlebar

"\

/ Guide Recess

 

• Handlebarmountingbracketfor1"

 

 

(2.5cm)shaft

 

 

• Handlebarmountingbracketfor7/8"

!er oe ino

(2.2cm)shaft

• Bracketcover(2)

SP_ff

RBe_ttase AttL°_erent

• Shoulderstrap

 

 

• Uppershoulderstrapclamp

,ram,WARNING:

Make sure the lock-

• Lowershoulderstrapclamp(with

 

£k

 

spacertabs)

• Handlebarbracketscrews(4) ing/release button is locked in the pri-

Shoulderstrapclampscrews(2) mary hole and the knob is securely

AttachmentHangertightened before operating the unit.

HexWrenchASSEMBLYHANDLEBAR

ExaminepartsfordamageDonotuse.

_lJ DANGER:

RISK OF CUT. To avoid

damagedparts.

 

 

 

 

 

 

 

NOTE:Ifyouneedassistanceorfind

serious injury, the barrier portion

of the

thatpartsaremissingordamaged,con-

handlebar

must

be

installed

as shown

tactyourSearsServiceCentre.

on the upper shaft

of the powerbead to

ASSEMBLY

 

provide a barrier between operator and

 

the spinning blade. Attach

handlebar

 

 

 

 

 

mounting bracket above arrow on

 

WARNING:Ifreceivedassembled,

 

 

 

 

 

repeatallstepstoensureyourunitis

safety warning decal on the upper

shaft (powerhead

end of unit).

 

properlyassembledandallfasteners

Ensure handlebar

is positioned

on

aresecure.

 

 

mounting

bracket

at the end of the ar-

• Ahexwrench(provided)isrequiredrow on the handlebar decal.

 

forassembly.

 

NOTE: Two mounting brackets are in-

INSTALLINGBRUSHCUTTER

AT-

cluded with this

attachment.

Both brack-

TACHMENT

 

 

 

ets are provided to adapt this attach-

CAUTION:

When removing

or instal-

ment for use with powerheads that have

ling attachments, place the unit on a

either a 1"

(2.5

cm) diameter or

a 7/8"

flat

surface

for

stability.

 

 

(2.2 cm) diameter upper shaft. The cor-

1.

Loosen

the

coupler by turning the

rect bracket must be used to ensure that

 

knob counterclockwise=

 

the handlebar is mounted securely to

 

 

 

 

 

 

 

 

 

 

the upper shaft before use.

 

 

 

Coupler

 

 

 

 

 

 

 

 

 

 

 

_OOSEN

Handlebar

_

_

Screw

 

 

 

 

 

 

 

 

 

TIGHTEN

Knob

ou2tito

 

 

2. Remove the shaft

cap from the

J

brushcutter attachment (if present).

 

3.Position locking/release button of attachment into guide recess of coupler.

4.Push the attachment into the cou-

pler until the locking/release button snaps into the primary hole.

Place the mounting bracket over the upper shaft above the arrow on the safety label. Be sure to use the correct mounting bracket for either the 1" (2.5 cm) or 7/8" (2.2 cm) diameter upper shaft.

Image 5
Contents Craftsmani Sears Canada, inc., Toronto, Ontario MSB 2B8 Commercial or Rental USEEyeProtection Thrown Operator SafetyUNIT/MAINTENANCE Safety Fuel Safety BeforeusingtheunitCutting Safety Transporting and StorageEr oe ino CoverscrewholesInserttwo Shoulder Strap AssemblyScrewsintothescrewholes WrenchBlade Know Your Brushcutter AttachmentOperating the Coupler Blade ShieldWhat Causes Blade Thrust Blade Thrust can occur when spin Installing AttachmentOperating Position Always Wear HangerRecommended Cutting Position When Blade Thrust Occurs Blade Thrust can occur withoutBlade Replacement Maintenance Schedule Care and Maintenance TaskBlade Maintenance Seasonal Storage