Craftsman 917.27268 manual To Attach Jumper Cables, Interlocks and Relays, To Replace Fuse

Page 26

TO START ENGINE WITH A WEAK

BATTERY

,_WARNING: Lead-acidbatteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from bat-

teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BAT- TERY" in the MAINTENANCE section of this manual).

If "jumper cables" are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -

1.Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

2.Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

3.Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER

1.BLACK cable first from chassis and then from the fully charged battery.

2.RED cable last from both batteries.

I

Weak or Dead Fully Charged

BatteryBattery

_wPLACING BATTERY ARNING: Do not short battery

terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands,

rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

1.Lift seat pan to raised position.

2.Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

3.Install new battery with terminals in same position as old battery.

4.First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal

5.Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely.

Terminal_//Keps

_-_ Nut Hex

Bolt

Positive

Negative (Black)

(Red) Cable

Cable

TO REPLACE HEADLIGHT BULB

1.Raise hood.

2.Pull bulb holder out of the hole in the backside of the grill.

3.Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

4.Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause

your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring

diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type

plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY

1.Raise hood.

2.Unsnap headlight wire connector.

3.Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

4.When replacing hood, be sure to re- connect the headlight wire connector.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents IC..FTSMeWl Limited Warranty on Craftsman Riding Equipment Limited Warranty on BatteryGeneral Operation II. Slope OperationIII. Children IV. ServiceDo not Across Agreements Sears Installation ServiceCustomer Responsibilities Steering Install Seat Howto SET UP Your TractorTools Required for Assembly To Remove Tractor fromCheck Battery Discharging Install Mulcher PlateCheck Deck Levelness Check for Proper Position of ALL BeltsH L I.,I Light Switch Know Your TractorHowto USE Your Tractor To Transport Before Starting the EngineTo Operate on Hills Towing Carts and Other ATTACH- MentsTo Start Engine Automatic Transmission Warm UPMowing Tips Purge TransmissionMulching Mowing Tips General Recommendations Before Each USEBlade Care BatteryOperator Presence System To Sharpen BladeLubrication EngineTransaxle Pump Fluid Engine Cooling Fins Clean AIR ScreenAIR Filter MufflerCleaning To Remove MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentBelt Installation To Adjust BrakeTo Check and Adjust Brake Belt RemovalFront Wheel TOE-IN/CAMBER Transmission Removal ReplacementAlignment To Remove Wheel for RepairsInterlocks and Relays To Remove Hood and Grill AssemblyTo Attach Jumper Cables To Replace FuseTo Adjust Carburetor To Adjust Throttle Control CablePreliminary Setting Acceleration Test Fuel System BatteryTractor Engine OILCause Troubleshooting ChartProblem Clean Cause CorrectionProblem Cause Correction Trash underTractor - Model Number Schematic OEo ÷IIIG OLAoKTractor - Model Number Electrical KEY Part Description Tractor - Model Number Chassis and Enclosures Tractor - Model Number Chassis and Enclosures Tractor - Model Number Ground Drive 200 Tractor - Model Number 917.272680 Steering Assembly Tractor - Model Number 917.272680 Steering Assembly Tractor - Model Engine Tractor - Model Number Engine Tractor - Model Number 917.272680 Seat Assembly KEY Part DescriptionX20 Tractor - Model Number DecalsTractor - Model Number Lift Assembly Tractor - Model Number Lift Assembly Tractor - Model Number Mower Deck 136420 =o= 032 434 O511 7o9 947 513 544Ao3,, 3,oi 106 690577 Seat-Inlet Wrench-Spark Plug Page Suggested Guide for Sighting Slopes for Safe Operation SE/AR

917.27268 specifications

The Craftsman 917.27268 is a standout model in the realm of riding mowers, designed to offer powerful performance combined with ease of use for both residential and commercial lawn care. This versatile riding mower is equipped with a host of features that make it a valuable asset for maintaining lush and healthy lawns.

One of the most notable aspects of the Craftsman 917.27268 is its robust engine. Powered by a reliable 19 horsepower Briggs & Stratton engine, this mower provides ample power to tackle tough terrains and thick grass. The engine is paired with an automatic transmission that allows for smooth and effortless speed adjustments, ensuring that operators can easily navigate through their lawns without any hassle.

The mower's cutting deck is another standout feature. With a 42-inch cutting width, it allows for efficient mowing, reducing the number of passes needed to cover large areas. The deck also has a three-blade system, which ensures a clean and even cut every time. Additionally, the cutting height can be easily adjusted to meet the specific needs of your lawn, offering six different height settings for an optimal finish.

Ergonomic design is a key characteristic of the Craftsman 917.27268. It features a comfortable seat with a high backrest that provides ample support during extended mowing sessions. The steering wheel is positioned for enhanced control, allowing users to maneuver the mower with confidence. The mower also includes a foot-operated deck lift for straightforward height adjustments, making it user-friendly for individuals of all skill levels.

When it comes to technology, the Craftsman 917.27268 incorporates various features designed to enhance functionality. For instance, it boasts an integrated mulching capability, allowing clippings to be finely chopped and returned to the lawn as natural fertilizer. This not only saves time but also promotes healthier grass growth. Additionally, the mower is equipped with a sturdy frame and durable wheels that ensure stability and longevity, reinforcing its position as a reliable choice for lawn maintenance.

In conclusion, the Craftsman 917.27268 delivers power, versatility, and user-friendly features, making it an ideal choice for anyone looking to maintain their lawn effectively. Its combination of a capable engine, efficient cutting system, ergonomic design, and thoughtful technologies creates an appealing package for homeowners and lawn care enthusiasts alike.
Top Page Image Contents