Craftsman 917.27268 manual Check Battery

Page 9

4.Pushdownon seatto engageshoulder

bolt in slot and pull seattowards rear of tractor.

5.Pivotseat and panforwardand as- sembleadjustmentknob and flat washerloosely.Do not tighten.

6.Lowerseat into operatingposition and sit in seat.

7.Slide seat untila comfortableposition is reachedwhichallows you to press clutch/brakepedalall the way down.

8.Get off seat without movingits ad- justed position.

9.Raiseseat and tighten adjustment knobsecurely.

Seat

Shoulder

Bolt

Adji Knob

CHECK BATTERY

1.Lift seat pan to raised position. NOTE: If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instruc- tions).

Seat

_rminat

NOTE: You may now roll or drive your

tractor off the skid. Follow the appropriate instruction below to remove the tractor

from the skid.

TO ROLLTRACTOR OFF SKID (See

Operation section for location and function of controls)

1.Press lift lever plunger and raise

attachment lift lever to its highest po- sition.

2.Release parking brake by depressing clutch/brake pedal.

3.Place freewheel control in "trans-

mission disengaged" position (See "TO TRANSPORT' in the Operation section

of this manual).

4.Roll tractor forward off skid.

5.Remove banding holding deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Operation section for location and function of controls)

,_IIWARNING: Before starting, read, un- derstand and follow all instructions in the

Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure

the area in front of tractor is clear of other people and objects.

1.Be sure all the above assembly steps have been completed.

2.Check engine oil level and fill fuel tank with gasoline.

3.Place freewheel control in "trans- mission engaged" position. (See "TO TRANSPORT' in the Operation section of this manual).

4.Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

5.Place motion control lever in neutral

(N)position.

6.Press lift lever plunger and raise

attachment lift lever to its highest posi- tion.

7.Start the engine. After engine has started, move throttle control to idle position.

8.Release parking brake.

9.Slowly move the motion control lever

forward and slowly drive tractor off skid.

10.Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

11.Turn ignition key to "STOP" position. Continue with the instructions that follow.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents IC..FTSMeWl Limited Warranty on Battery Limited Warranty on Craftsman Riding EquipmentII. Slope Operation General OperationIV. Service Do notIII. Children Across Sears Installation Service Customer ResponsibilitiesAgreements Steering Tools Required for Assembly Howto SET UP Your TractorInstall Seat To Remove Tractor fromCheck Battery Check Deck Levelness Install Mulcher PlateDischarging Check for Proper Position of ALL BeltsH L I.,I Know Your Tractor Light SwitchHowto USE Your Tractor To Operate on Hills Before Starting the EngineTo Transport Towing Carts and Other ATTACH- MentsAutomatic Transmission Warm UP To Start EnginePurge Transmission Mowing TipsMulching Mowing Tips Before Each USE General RecommendationsOperator Presence System BatteryBlade Care To Sharpen BladeEngine Transaxle Pump FluidLubrication AIR Filter Clean AIR ScreenEngine Cooling Fins MufflerTo Remove Mower CleaningSIDE-TO-SIDE Adjustment To Level Mower HousingTo Check and Adjust Brake To Adjust BrakeBelt Installation Belt RemovalAlignment Transmission Removal ReplacementFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsTo Attach Jumper Cables To Remove Hood and Grill AssemblyInterlocks and Relays To Replace FuseTo Adjust Throttle Control Cable Preliminary SettingTo Adjust Carburetor Acceleration Test Tractor BatteryFuel System Engine OILTroubleshooting Chart ProblemCause Cause Correction CleanTrash under Problem Cause CorrectionOEo ÷IIIG OLAoK Tractor - Model Number SchematicTractor - Model Number Electrical KEY Part Description Tractor - Model Number Chassis and Enclosures Tractor - Model Number Chassis and Enclosures Tractor - Model Number Ground Drive 200 Tractor - Model Number 917.272680 Steering Assembly Tractor - Model Number 917.272680 Steering Assembly Tractor - Model Engine Tractor - Model Number Engine KEY Part Description Tractor - Model Number 917.272680 Seat AssemblyTractor - Model Number Decals X20Tractor - Model Number Lift Assembly Tractor - Model Number Lift Assembly Tractor - Model Number Mower Deck 136420 =o= 032 434 O511 7o9 947 513 544Ao3,, 3,oi 106 690577 Seat-Inlet Wrench-Spark Plug Page Suggested Guide for Sighting Slopes for Safe Operation SE/AR

917.27268 specifications

The Craftsman 917.27268 is a standout model in the realm of riding mowers, designed to offer powerful performance combined with ease of use for both residential and commercial lawn care. This versatile riding mower is equipped with a host of features that make it a valuable asset for maintaining lush and healthy lawns.

One of the most notable aspects of the Craftsman 917.27268 is its robust engine. Powered by a reliable 19 horsepower Briggs & Stratton engine, this mower provides ample power to tackle tough terrains and thick grass. The engine is paired with an automatic transmission that allows for smooth and effortless speed adjustments, ensuring that operators can easily navigate through their lawns without any hassle.

The mower's cutting deck is another standout feature. With a 42-inch cutting width, it allows for efficient mowing, reducing the number of passes needed to cover large areas. The deck also has a three-blade system, which ensures a clean and even cut every time. Additionally, the cutting height can be easily adjusted to meet the specific needs of your lawn, offering six different height settings for an optimal finish.

Ergonomic design is a key characteristic of the Craftsman 917.27268. It features a comfortable seat with a high backrest that provides ample support during extended mowing sessions. The steering wheel is positioned for enhanced control, allowing users to maneuver the mower with confidence. The mower also includes a foot-operated deck lift for straightforward height adjustments, making it user-friendly for individuals of all skill levels.

When it comes to technology, the Craftsman 917.27268 incorporates various features designed to enhance functionality. For instance, it boasts an integrated mulching capability, allowing clippings to be finely chopped and returned to the lawn as natural fertilizer. This not only saves time but also promotes healthier grass growth. Additionally, the mower is equipped with a sturdy frame and durable wheels that ensure stability and longevity, reinforcing its position as a reliable choice for lawn maintenance.

In conclusion, the Craftsman 917.27268 delivers power, versatility, and user-friendly features, making it an ideal choice for anyone looking to maintain their lawn effectively. Its combination of a capable engine, efficient cutting system, ergonomic design, and thoughtful technologies creates an appealing package for homeowners and lawn care enthusiasts alike.
Top Page Image Contents