Craftsman 917.27631 Interlocks and Relays, To Replace Fuse, To Remove Hood and Grill AS- Sembly

Page 25

4.Install new batterywith terminalsin same positionas old battery.

5.Reinstallterminalguard.

6.First connect RED batterycableto positive(+) batteryterminalwith hex bolt and keps nutas shown.Tighten securely.

7.ConnectBLACKgroundingcableto negative(-) batteryterminalwith re- maininghex bolt and keps nut.Tighten securely

8.Closeterminalaccess doors.

9. Closehood.

Keps,,Nut __

Headlight Wire Connector

Terrain

ex Bolt

AccessDoor(Red)

;_.._,_r _._ _ Cable

TerminaF"_h _ _-

Guard _'._ "Negative (Black)

_"_ _ Cable

TO REPLACE HEADLIGHT BULB

1.Raise hood.

2.Pull bulb holder out of the hole in the backside of the grill.

3.Replace bulb in holder and push bulb holder securely back into the hole in

the backside of the grill.

4.Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause

your tractor to run poorly, stop running, or prevent it from starting.

• Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 30 amp automotive-type

plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL AS- SEMBLY

1.Raise hood.

2.Unsnap headlight wire connector.

3.Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

4.When replacing hood, be sure to re- connect the headlight wire connector.

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers ex- pense, may be performed by any non-roadengine repair establishment or individual. Warranty repairs must be performed by an

authorized engine manufacturer's service outlet.

TO ADJUSTTHROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be nec- essary. Check adjustment as described below before loosening cable. If adjust- ment is necessary, proceed as follows:

1.With engine not running, move throttle control lever to fast position.

2.Check that swivel is against stop. If it is not, loosen cable clamp screw and pull cable back until swivel is against stop.

Tighten cable clamp screw securely.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and adjustment should not be nec- essary. Check adjustment as described below before loosening cable. If adjust- ment is necessary, proceed as follows:

1.With engine not running, move choke control (located on dash panel) to full choke position.

2.Loosen knob and remove cover as- sembly from air cleaner.

3.Choke should be closed. If it is not, loosen casing clamp screw and move choke cable until choke is completely closed. Tighten casing clamp screw securely.

4.Replace air cleaner cover assembly and tighten knob.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents ICHFT=MeN Limited Warranty on Battery Limited Warranty on Craftsman Riding EquipmentGeneral Operation II. Slope Operation Service Safe Handling of GasolineII1. Children IV. TowingGeneral Service Sears Installation Service Product SpecificationsCustomer Responsibilities Repair Protection AgreementsAdjust Seat Check BatteryTo Remove Tractor from Carton Unpack CartonTo Drive Tractor OFF Skid ChecklistChecktire Pressure Check Deck Levelness===m Lever Know YOU R TractorLift Lever LightHowto Useyourtractor To Adjust Mower Cutting HeightStopping To SET Parking BrakeUsing the Reverse Operation System To Adjust Gauge WheelsTo Operate Mower Reverse Operation System ROSTo Transport Before Starting the EngineCheck Engine OIL Level Mowing Tips General Recommendations ChartBefore Each USE Check engine oil level Check brake operationBrake Operation TractorTires Operator Presence SystemEngine BatteryTransaxle Cooling Check Transaxle OIL LevelAIR Filter Clean AIR ScreenMuffler Vice or Adjustments CleaningFlanged Pins TractorTo Level Mower Housing To Install MowerSIDE-TO-SIDE Adjustment FRONT-TO-BACK AdjustmentTo Replace Mower Drive Belt Both Front Plate Links Must be Equal in LengthMower Drive Belt Removal To Replace Mower Blade SEC Ondary Drive Belt To Check and Adjust Brake To Adjust Attachment ClutchLocknut With parking brake EngagedReplacing Battery To Adjust Steering Wheel ALIGN- MentTo Start Engine with Aweak BAT- Tery To Remove Wheel for Repairs Front WheelTo Adjust Choke Control To Adjustthrottle Control CableInterlocks and Relays To Replace FuseTo Adjust Carburetor Fuel System Fully charge the battery for storageEngine OIL CylindersProblem Troubleshooting ChartHard to start Engine will not turn over Cause3ORRECTION Problem CauseMower blades will When turning engine OFFNot rotate CorrectionTRACTOR- Model Number SchematicElectrical Tractor - Model NumberKEY Part Description Tractor - Model Number Chassis and Enclosures TRACTOR- Model Number Chassis and Enclosures Tractor - Model Number Ground Drive 7563R TRACTOR- Model Number Ground DriveTractor - Model Number Steering Assembly KEY Part NO. no TRACTOR- Model Number Steering Assembly21 J KEY Part Tractor - Model Number Seat AssemblyDescription Wheels Decals121006X Red Asm,, Lever Lift AssemblyTractor - Model Number Mower Deck Relief TRACTOR- Model Number Mower DeckTransaxle 174731 Transaxle265 48m 3o3 Briggs & Stratton ENGINE-MODEL Tractor Model NumberNumber 446677-0470-E1 Page Page Suggested Guide for Sighting Slopes for Safe Operation 11-800-469-4663 Your Home

917.27631 specifications

The Craftsman 917.27631 is a robust lawn mower designed for homeowners who seek a reliable, efficient, and durable machine for maintaining their lawns. This mower features a powerful 21-inch cutting deck, making it capable of handling medium to large-sized yards with ease. One of its standout features is the 163cc gas engine, which provides ample power for tackling tough grass and uneven terrain while ensuring reliable starts and consistent performance.

The Craftsman 917.27631 is equipped with a self-propelled drive system, which allows users to navigate effortlessly through their lawns without the need for excessive physical strain. The variable speed control gives users the option to adjust the speed according to their preference and the terrain, ensuring optimal maneuverability. This feature is particularly beneficial for navigating around garden beds, trees, and other obstacles.

Another impressive aspect of the Craftsman 917.27631 is its 3-in-1 cutting capability. This versatile mower allows users to choose between mulching, bagging, or side discharge, providing flexibility based on preferences and conditions. The mulching capability promotes healthy lawn growth by returning finely chopped grass back to the soil, while the rear bagging option allows for easy collection of clippings for disposal or composting.

The mower also boasts an adjustable cutting height, which can be easily altered to ensure the perfect grass length for various seasons and grass types. Users can choose from multiple height settings, ensuring compatibility with different mowing needs. Moreover, the durable and lightweight construction of the Craftsman 917.27631 enhances its maneuverability and makes it easier to transport and store.

Safety features are paramount in the design of the Craftsman 917.27631. The engine will stop immediately when the operator releases the handle, preventing accidental injuries and promoting safe operation. Additionally, the ergonomic handle design adds comfort, reducing fatigue during prolonged use.

In summary, the Craftsman 917.27631 is a versatile, powerful, and easy-to-use lawn mower that caters to a wide array of lawn maintenance needs. With its self-propelling capabilities, adjustable cutting height, and efficient 3-in-1 cutting options, it represents a solid choice for any homeowner looking to maintain a pristine lawn with minimal effort.
Top Page Image Contents